Asymmetric Structure Research Articles

Enhanced response over wavelength range of 7–12 µm for quantum wells in asymmetric micro-pillars

Efficient coupling in broad wavelength range is desirable for wide-spectrum infrared light detection, yet this is a challenge for intersubband transition in semiconductor quantum wells (QWs). High-Q cavities mostly intensify the absorption at peak wavelengths but with shrinking bandwidth. Here, we propose a novel approach to expand the operating spectral range of the Quantum Well Infrared Photodetectors (QWIPs). By processing the QWs into asymmetric micro-pillar array structure, the device demonstrates a substantial enhancement in spectral response across the wavelength from 7.1 µm to 12.3 µm with guided mode resonance (GMR) effects. The blackbody responsivity is then increased by 3 times compared to that of the 45° polished edge-coupled counterpart. Meanwhile, the dark current density remains unchanged after the deep etching process, which will benefit the electrical performance of the detector with reduced volume duty ratio. In contrast to the symmetric micro-pillar array that contains simple resonance mode, the detectivity of QWIP in asymmetric pillar structure is found to be improved by 2-4 times within the range of 9.5 µm to 15 µm.

Preparation and properties of asymmetric inverse opal-like microfiltration membranes

Most types of commercially available MF membranes suffer limited separation performances due to huge deviations in pore size and low porosity. In view of this, a new and facile assembly strategy was proposed to prepare an asymmetric inverse opal (IO) like microfiltration (MF) membrane with ordered pore structure, high porosity and large water flux, which is a composite of a disordered layer with three-dimensional pore structures made by dissolved N, N-dimethylformamide (DMF) and an ordered layer with uniform pore size by using a sacrificial template method. The effects of SiO2 microsphere size and DMF treatment on the structure and properties have been investigated. Different DMF treatment times can significantly change the asymmetric structure distribution of MF membrane and further affect the permeability. The water flux of the asymmetric membrane increases with the DMF infiltration time. Based on the SiO2 microsphere template size of 494 nm and the DMF treatment time of 90 s, the porosity and pure water flux can reach 78 % and 1810 L/m2h, respectively. The membrane retains the IO-like structure layer with uniform pore size, and features excellent retention (almost 100 %) for SiO2 microspheres, indicating the great potential of asymmetric IO-like MF membranes for membrane separation applications.

Symmetry‐breaking of Dibenzo[b,d]thiophene Sulfone Enhancing Polaron Generation for Boosted Photocatalytic Hydrogen Evolution

The current bottleneck in the development of efficient photocatalysts for hydrogen evolution is the limited availability of high‐performance acceptor units. Over the past nine years, dibenzo[b,d]thiophene sulfone (DBS) has been the preferred choice for the acceptor unit. Despite extensive exploration of alternative structures as potential replacements for DBS, a superior substitute remains elusive. In this study, a symmetry‐breaking strategy was employed on DBS to develop a novel acceptor unit, BBTT‐1SO. The asymmetric structure of BBTT‐1SO proved beneficial for increasing multiple moment and polarizability. BBTT‐1SO‐containing polymers showed higher efficiencies for hydrogen evolution than their DBS‐containing counterparts by up to 166%. PBBTT‐1SO exhibited an excellent hydrogen evolution rate (HER) of 222.03 mmol g−1 h−1 and an apparent quantum yield of 27.5% at 500 nm. Transient spectroscopic studies indicated that the BBTT‐1SO‐based polymers facilitated electron polaron formation, which explains their superior HERs. PBBTT‐1SO also showed 14% higher HER in natural seawater splitting than that in deionized water splitting. Molecular dynamics simulations highlighted the enhanced water‐PBBTT‐1SO polymer interactions in salt‐containing solutions. This study presents a pioneering example of a substitute acceptor unit for DBS in the construction of high‐performance photocatalysts for hydrogen evolution.

Asymmetries During Eyewall Replacement Cycles of Hurricane Ivan (2004)

Abstract The physical processes that govern eyewall replacement cycles (ERCs) in tropical cyclones (TCs) are not yet fully understood. In particular, asymmetric structures within the TC inner core have an uncertain role in ERC dynamics. This study analyzes the kinematic and precipitation asymmetric structures during successive ERCs in Hurricane Ivan (2004) using airborne Doppler radar observations. The azimuthal locations of these asymmetries are analyzed relative to the deep-layer (850-200 hPa) environmental wind shear vector. Two ERCs were analyzed at different stages of their evolution. During the concentric eyewall stage of the first ERC, the outer eyewall updrafts were strongest in the left-of-shear half, which also coincided with mesoscale descending inflow (MDI) just radially outward. Enhanced low-level convergence, updrafts, and MDI were collocated in an zone spiraling inward towards the strongest outer eyewall updrafts, suggesting that the vertical velocity asymmetry in the outer eyewall was possibly forced by a stratiform-induced cold pool similar to MDI impacts seen in past TC studies. During the final stage of the second ERC, the outer eyewall (now the singular primary eyewall) experienced an upwind shift in the precipitation and vertical velocity asymmetries. The updraft maximum shifted from the downshear-left quadrant to the downshear-right quadrant, and the precipitation maximum (downwind of the updraft maximum) shifted from left-of-shear to the downshear direction. This shift corroborates previous studies, which hypothesize that at the end of an ERC, the forcing mechanism that drives the eyewall vertical velocity asymmetry transitions from MDI/cold-pool processes to direct interaction with the environmental wind shear.

Azimuthal rotation-controlled nanoinscribing for continuous patterning of period- and shape-tunable asymmetric nanogratings

We present an azimuthal-rotation-controlled dynamic nanoinscribing (ARC-DNI) process for continuous and scalable fabrication of asymmetric nanograting structures with tunable periods and shape profiles. A sliced edge of a nanograting mold, which typically has a rectangular grating profile, slides over a polymeric substrate to induce its burr-free plastic deformation into a linear nanopattern. During this continuous nanoinscribing process, the “azimuthal angle,” that is, the angle between the moving direction of the polymeric substrate and the mold’s grating line orientation, can be controlled to tailor the period, geometrical shape, and profile of the inscribed nanopatterns. By modulating the azimuthal angle, along with other important ARC-DNI parameters such as temperature, force, and inscribing speed, we demonstrate that the mold-opening profile and temperature- and time-dependent viscoelastic polymer reflow can be controlled to fabricate asymmetric, blazed, and slanted nanogratings that have diverse geometrical profiles such as trapezoidal, triangular, and parallelogrammatic. Finally, period- and profile-tunable ARC-DNI can be utilized for the practical fabrication of diverse optical devices, as is exemplified by asymmetric diffractive optical elements in this study.

Miniaturized leaky-wave antenna with backward-to-forward beam scanning and suppressed open stop-band based on substrate-integrated plasmonic waveguide

This work presents a theoretical design and experimental demonstration of a novel miniaturized leaky-wave antenna (LWA) using composite waveguide based on substrate-integrated plasmonic waveguide (SIPW). The SIPW is designed by embedding hybrid dual spoof surface plasmon polariton (SSPP) structure into a three-layer substrate integrated waveguide (SIW). Due to the slow-wave effect of SIPW, the proposed miniaturized composite waveguide forms slowed phase velocity and decreased lower cutoff frequency. To excite backward-to-forward beam scanning mode and suppress the open stop-band, an asymmetric sinusoidal modulated structure is introduced to the surface of the composite waveguide. The experimental results indicate that the proposed SIPW-based LWA can achieve continuous beam scanning from the backward to the forward direction within the bandwidth of 10.6-13.7 GHz, passing through the broadside at 11.6 GHz.

Asymmetric nanofiber photothermal interactive electronic skin with triboelectric autonomous thermal perceptivity

Thermal-perceptive electronic skins (e-skin) represent an important functional interface in wearables and soft robots. Realizing an all-in-one structured nanofiber interactive e-skin with autonomous thermal perceptivity remains challenging. We demonstrated a polyurethane/(polyvinyl pyrrolidone/MXene) (PPM) bilayer nanofiber film with asymmetric structure compactness by continuous and controllable electrospinning, that achieves asymmetric optical transmittance (visible light transparency of 20∼97%, infrared transparency of 5.5∼34.1%) and photothermal actuation response, with a response rate of 0.8 mm−1 s−1 and bending curvature of 2.2 cm−1, as well as additional excellent triboelectric outputs of ∼320 V and ∼5.4 µA. We proposed a “contact-actuation-perception” strategy for instantaneous object temperature sensing based on the PPM, which can actuate under photothermal stimulation to change its contact area with the target objects at different temperatures, producing temperature-dependent distinguishable triboelectric signals for autonomous thermal perception, with sensitivity up to ∼99.6%. This work could inspire a facile strategy to realize asymmetric features in fiber materials, in which the asymmetric optical-thermal-mechanical-electrical coupling mechanism for active perception is expected to promote the development of autonomous interactive e-skins.

NIR-II Absorbed Dithienopyrrole-Benzobisthiadiazole Based Nanosystems for Autophagy Inhibition and Calcium Overload Enhanced Photothermal Therapy.

Although the current cancer photothermal therapy (PTT) can produce a powerful therapeutic effect, tumor cells have been proved a protective mechanism through autophagy. In this study, a novel hybrid theranostic nanoparticle (CaCO3@CQ@pDB NPs, CCD NPs) is designed and prepared by integrating a second near-infrared (NIR-II) absorbed conjugated polymer DTP-BBT (pDB), CaCO3, and autophagy inhibitor (chloroquine, CQ) into one nanosystem. The conjugated polymer pDB with asymmetric donor-acceptor structure shows strong NIR-II absorbing capacity, of which the optical properties and photothermal generation mechanism of pDB are systematically analyzed via molecular theoretical calculation. Under NIR-II laser irradiation, pDB-mediated PTT can produce powerful killing ability to tumor cells. At the same time, heat stimulates a large amount of Ca2+ inflow, causing calcium overload induced mitochondrial damage and enhancing the apoptosis of tumor cells. Besides, the released CQ blocks the self-protection mechanism of tumor cells and greatly enhances the attack of PTT and calcium overload therapy. Both in vitro and in vivo experiments confirm that CCD NPs possess excellent NIR-II theranostic capacity, which provides a new nanoplatform for anti-tumor therapy and builds great potential for future clinical research.

On the structure dynamic response induced by the dam-break surge impact using multivariate copulas

In this study, the dam-break induced surge impact pressure data on a vertical wall are used to investigate the corresponding structure dynamic response. Both the hydrodynamic and structure parameters are confirmed to be crucial in assessing the structure dynamic responses. The surge peak pressure pk, the pressure rise time Tr, the surge impact duration Td, and the structure natural period Tn are considered to establish the statistical model. The present study determines the dependencies among these parameters which describe the structure dynamic response due to the complexity of dam breaking. Accordingly, two multivariate copulas, i.e., the Gaussian copula and the Vine copula, are used to simulate the statistical properties of the maximum dynamic amplification factor ψm, allowing a better understanding of the dependencies and correlations among different parameters. The tail dependence of variable pairs (pk, Tr) and (pk, ψm) are not significant, while the variable pairs (Tr, ψm) and (Td/Tn, ψm) show lower and upper tail dependence. With respect to the experiment data, simulation using the Gaussian copula shows good results regarding variable pairs of symmetric dependence structures, whereas the Vine copula is more suitable for variable pairs of asymmetric dependence structures.

High-sensitivity strain sensor based on an asymmetric tapered air microbubble Fabry-Pérot interferometer with an ultrathin wall

A Fabry-Pérot interferometer (FPI) with an asymmetric tapered structure and air microbubble with an ultrathin wall is designed for high-sensitivity strain measurement. The sensor contains an air microbubble formed by two single-mode fibers (SMF) prepared by fusion splicer arc discharge, and a taper is applied to one side of the air microbubble with a wall thickness of 3.6 µm. In this unique asymmetric structure, the microbubble is more easily deformed under stress, and the strain sensitivity of the sensor is up to 15.89 pm/µɛ as evidenced by experiments.The temperature sensitivity and cross-sensitivity of the sensor are 1.09 pm/°C and 0.069 µɛ/°C in the temperature range of 25-200°C, respectively, thus reducing the measurement error arising from temperature variations. The sensor has notable virtues such as high strain sensitivity, low-temperature sensitivity, low-temperature cross-sensitivity, simple and safe process preparation, and low cost. Experiments confirm that the sensor has good stability and repeatability, and it has high commercial potential, especially strain measurements in complex environments.

High barrier polyesters based on 2,5-furandicarboxylic acid and disulfide bond: Smart degradation induced by low concentrations of redox reagent

Bio-based and biodegradable polymers opens up opportunities to overcome resource depletion and plastic pollution. However, the degradation mechanism based on ester bond breakage makes it difficult to achieve controllable degradation induced by external stimuli. In this work, we present a new 2,5-furandicarboxylic acid-based copolyesters (PBFDi) by partially replacing carbon–carbon backbones with disulfide bonds and discuss the influence of disulfide bonds on thermal stability, crystallization behavior, mechanical and barrier properties of polyesters. They could maintain stable for 1 h at processing temperatures of 220 °C, meeting the needs of long-term melt processing. The asymmetric structure of the furan ring and the slower free rotation of disulfide bonds help restrict the mobility of chains and obstruct gas permeation, resulting in 9.3–126.7 times increase in O2 barrier than commercial PBAT. With the introduction of small amount (≤40 %) of disulfide bond units, the hydrolysis rate is relatively slow and can maintain stable during storage and use. As expected, the copolyesters show redox dual-responsive degradation. Even at low concentrations (0.01 M and 0.1 M) of H2O2, the transition from hydrophobicity to hydrophilicity can be achieved, expected to accelerate the hydrolysis of PBFDi. The fast cleavage of disulfide bonds induced by DTT could be influenced by the copolymerized FDCA units. Lastly, the redox dual-responsive mechanism is elucidated, and how the rigid FDCA co-monomers affect the redox dual responsiveness is also clarified.

Tandem Electric-Fields Prolong Energetic Hot Electrons Lifetime for Ultra-Fast and Stable NO2 Detection.

Prolonging energetic hot electrons lifetimes and surface activity in the reactive site can overcome the slow kinetics and unfavorable thermodynamics of photo-activated gas sensors. However, bulk and surface recombination limit the simultaneous optimization of both kinetics and thermodynamics. Here tandem electric fields are deployed at (111)/(100)Au-CeO2 to ensure a sufficient driving force for carrier transfer and elucidate the mechanism of the relationship between charge transport and gas-sensing performance. The asymmetric structure of the (111)/(100)CeO2 facet junction provides interior electric fields, which facilitates electron transfer from the (100)face to the (111)face. This separation of reduction and oxidation reaction sites across different crystal faces helps inhibit surface recombination. The increased electron concentration at the (111)face intensifies the interface electric field, which promotes electron transfer to the Au site. The local electric field generated by the surface plasmon resonance effect promotes the generation of high-energy energy hot-electrons, which maintains charge concentration in the interface field by injecting into (111)/(100)CeO2, thereby provide thermodynamic contributions and inhibit bulk recombination. The tandem electric fields enable the (111)/(100)Au-CeO2 to rapidly detect 5ppm of NO2 at room temperature with stability maintained within 20s.

Poly(ethylene oxide)- and Polyzwitterion-Based Thermoplastic Elastomers for Solid Electrolytes.

In this article, ABA triblock copolymer (tri-BCP) thermoplastic elastomers with poly(ethylene oxide) (PEO) middle block and polyzwitterionic poly(4-vinylpyridine) propane-1-sulfonate (PVPS) outer blocks were synthesized. The PVPS-b-PEO-b-PVPS tri-BCPs were doped with lithium bis-(trifluoromethane-sulfonyl) imide (LiTFSI) and used as solid polyelectrolytes (SPEs). The thermal properties and microphase separation behavior of the tri-BCP/LiTFSI hybrids were studied. Small-angle X-ray scattering (SAXS) results revealed that all tri-BCPs formed asymmetric lamellar structures in the range of PVPS volume fractions from 12.9% to 26.1%. The microphase separation strength was enhanced with increasing the PVPS fraction (fPVPS) but was weakened as the doping ratio increased, which affected the thermal properties of the hybrids, such as melting temperature and glass transition temperature, to some extent. As compared with the PEO/LiTFSI hybrids, the PVPS-b-PEO-b-PVPS/LiTFSI hybrids could achieve both higher modulus and higher ionic conductivity, which were attributed to the physical crosslinking and the assistance in dissociation of Li+ ions by the PVPS blocks, respectively. On the basis of excellent electrical and mechanical performances, the PVPS-b-PEO-b-PVPS/LiTFSI hybrids can potentially be used as solid electrolytes in lithium-ion batteries.

Evidence of disordered local structure of ZnO buffered MgB2 films via polarized extended X-ray absorption fine structure analysis

Herein, we investigated the mechanism by which the critical temperature (Tc) of a magnesium diboride (MgB2) superconductor is altered by the buffer layer. Zinc oxide (ZnO) layers with different thicknesses (28, 80, and 134 nm) were deposited epitaxially on a Hastelloy substrate beneath a ∼ 1 μm MgB2 film. To measure the local structural distortion of the boron plane, three different angle polarizations (0°, 45°, and 90° parallel to the ab-axis) on the Mg K-edge, extended X-ray absorption fine structure (EXAFS) measurements were performed. The EXAFS analyses revealed that the ZnO buffer layer caused the boron layer to disorient, leading to buckling between the Mg and B layers, which affected the charge transfer capability in the intra-layer structure. Furthermore, the uneven distribution of B atoms amid the surrounding Mg atoms resulted in an asymmetric crystal structure, which leads to Tc fluctuation. This study reveals the relationship between modifications made to the boron plane condition of MgB2 by the ZnO buffer layer and the superconducting Tc behavior of MgB2.

Perpendicular magnetic properties and field-free current-induced switching in W/CoFeB/MgO trilayers with a compensating oblique W underlayer

Zero-field magnetization switching (ZFS) driven by current-induced spin–orbit torque (SOT) holds significant importance in spintronic applications. The introduction of a lateral asymmetric structure (LAS) through oblique deposition proves to be an effective strategy for breaking inversion symmetry, thereby enabling SOT-driven ZFS. However, the coexistence of wedge thickness structure and slanted columnar microstructure in the obliquely deposited films poses challenges in distinguishing their respective effects. In this study, we conducted a comparative investigation of the perpendicular magnetic properties and current-induced switching in W/Co40Fe40B20/MgO films by oblique sputtering of the W underlayer at a fixed tilting angle and at two opposite tilting angles with its wedge thickness compensated. We have found that the perpendicular magnetic properties of the Co40Fe40B20 layer are significantly altered at large tilting angles, irrespective of whether the W wedge thickness is compensated. Notably, at a tilting angle of 50°, ZFS is realized for both the conventional oblique sample and the compensating oblique sample, with the switching polarity contingent on the final tilting direction of the W layer. We have identified a gradient in perpendicular magnetic anisotropy in these samples, attributed to the laterally varying roughness associated with the slanted columnar microstructure of the W underlayer. This study underscores the dominant role of microscopic LAS in obliquely deposited films in breaking SOT symmetry. Our research sheds light on the impact of the slanted columnar microstructure on the magnetic and magneto-transport properties of films, offering valuable insights for advancing spintronic device research.

DKNN: deep kriging neural network for interpretable geospatial interpolation

Geospatial interpolation plays a pivotal role in spatial analysis because it provides high-quality data support for various spatiotemporal data mining (STDM) tasks. However, statistical methods, such as kriging, face challenges in dealing with complex geo-big data. Additionally, deep-learning-based methods, despite their exceptional performance, suffer from limitations, such as poor interpretability. To harness the complementary advantages of these statistical methods and deep learning approaches, this study proposes a novel geospatial artificial intelligence (GeoAI) framework called deep kriging neural network (DKNN). The primary contribution lies in the development of an asymmetric encoder-decoder structure, which includes a deep-learning-based spatial encoder and a geostatistics-based kriging decoder. The spatial encoder consists of three specialized neural networks, whereas the kriging decoder relies on the proposed unified kriging system. During forward propagation, the kriging decoder leverage messages from the spatial encoder to generate interpolation weights for prediction. Conversely, during backward propagation, the kriging decoder guides the spatial encoder in learning interpretable knowledge. Experiments were conducted using both synthetic and practical datasets. The results demonstrate an average improvement of 20.18% in MAE, 25.04% in RMSE and 24.06% in MAPE when compared to the best-performing baseline method. Furthermore, these results confirm the superior interpretability of our DKNN framework.

Laboratory visualization of damage asymmetry formation of rock fracture via acoustic emission and digital imaging correlation

Rock fracture mechanics and accurate characterization of rock fracture are crucial for understanding a variety of phenomena interested in geological engineering and geoscience. These phenomena range from very large-scale asymmetrical fault structures to the scale of engineering projects and laboratory-scale rock fracture tests. Comprehensive study can involve mechanical modeling, site or post-mortem investigations, and inspection on the point cloud of the source locations in the form of earthquake, micro-seismicity, or acoustic emission. This study presents a comprehensive data analysis on characterizing the forming of the asymmetrical damage zone around a laboratory mixed-mode rock fracture. We substantiate the presence of asymmetrical damage through qualitative analysis and demonstrate that measurement uncertainties cannot solely explain the observed asymmetry. The implications of this demonstration can be manifold. On a larger scale, it solidifies a mechanical model used for explaining the contribution of aseismic mechanisms to asymmetrical fault structures. On a laboratory scale, it exemplifies an alternative approach to understanding the observational difference between the source location and the in situ or post-mortem inspection on the rock fracture path. The mechanical model and the data analysis can be informative to the interpretations of other engineering practices as well, but may face different types of challenges.

The impact of the Olympics on the causality between the Chinese and international equity markets

Considering the economic impact of hosting the Olympic Games, this work explores the relationship between the Chinese and international equity markets before and after the two Olympic Games hosted in China. We choose SSEC as the representative of the Chinese equity market and DJI and N225 as the representatives of the international equity market. In addition, we compare the impacts of the summer and winter Olympics. Through the event analysis perspective, the entire sample is divided, and then the relationship between equity markets in different periods is analysed. First, the test results show that DJI affects SSEC at all times, but SSEC cannot affect DJI. Second, we cannot find a linkage between SSEC and N225. However, the Hatemi-J test revealed that there was a significant asymmetric relationship between markets during the Summer Olympics and Winter Olympics, and this asymmetric structure changed in the later stages of the Olympic Games. Additionally, the asymmetric structure is inconsistent between the summer and winter Olympic periods. This work may therefore be of great value for improving economic efficiency, avoiding financial risks, or optimizing portfolio decisions.

Eco-friendly wearable textiles: Asymmetric structures for EMI shielding, thermal management, and fire safety

This work focuses on developing multifunctional wearable fabrics, specifically targeting the challenge of flammability in this context. An eco-friendly, asymmetrically structured nylon/cotton blend fabric is prepared through the surface modification of phytic acid-induced polyaniline, the application of silver nanowires (AgNWs) and MXene on both sides and encapsulated by polydimethylsiloxane (PDMS). The AgNWs coating suppresses thermal radiation from the human body to achieve radiative heating, while the MXene coating enhances solar heating, ensuring thermal comfort in cold conditions. The treated fabric also exhibits electrical heating for heat compensation in the absence of sunlight, remarkable EMI shielding performance (55.6 dB) is also achieved. Enhanced fire safety is demonstrated as the treated fabric extinguishes when exposed to flame, reducing heat release by 45.9 % relative to the control nylon/cotton blend fabric (CO/NY). Additionally, the treated fabric exhibits significant antibacterial properties against Gram-negative E. coli and Gram-positive S. aureus, along with a notable water contact angle (WCA) of 130.2°. This work provides a promising method for the development of eco-friendly wearable smart fabrics with well-balanced desirable properties.

A Janus, robust, biodegradable bacterial cellulose/Ti3C2Tx MXene bilayer membranes for guided bone regeneration

Guided bone regeneration (GBR) stands as an essential modality for craniomaxillofacial bone defect repair, yet challenges like mechanical weakness, inappropriate degradability, limited bioactivity, and intricate manufacturing of GBR membranes hindered the clinical efficacy. Herein, we developed a Janus bacterial cellulose(BC)/MXene membrane through a facile vacuum filtration and etching strategy. This Janus membrane displayed an asymmetric bilayer structure with interfacial compatibility, where the dense layer impeded cell invasion and the porous layer maintained stable space for osteogenesis. Incorporating BC with Ti3C2Tx MXene significantly enhanced the mechanical robustness and flexibility of the material, enabling clinical operability and lasting GBR membrane supports. It also contributed to a suitable biodegradation rate, which aligned with the long-term bone repair period. After demonstrating the desirable biocompatibility, barrier role, and osteogenic capability in vitro, the membrane's regenerative potential was also confirmed in a rat cranial defect model. The excellent bone repair performance could be attributed to the osteogenic capability of MXene nanosheets, the morphological cues of the porous layer, as well as the long-lasting, stable regeneration space provided by the GBR membrane. Thus, our work presented a facile, robust, long-lasting, and biodegradable BC/MXene GBR membrane, offering a practical solution to craniomaxillofacial bone defect repair.