Ash Leachate Research Articles

Ultrasound assisted bio-acid leaching of sewage sludge ash for phosphorus extraction using lemon juice: optimization and ecological risk assessment

Ultrasound assisted bio-acid leaching of sewage sludge ash for phosphorus extraction using lemon juice: optimization and ecological risk assessment

The Impacts of Volcanic Activity on Microbial Growth—A Simulation Experiment in the Qiliao Section in Shizhu County, Chongqing, China

The impact of volcanic activity on microorganisms has always been a hot topic of discussion during geological history. Further studies are needed on the effects of volcanic activity on microbial growth in shale and the differences in nutrients provided by volcanic ash and other weathered rocks. This study’s results indicated that TOC contents at the bottom of the shale layer are 1.93–4.44% and 3.0% on average. The TOC contents at the top of the layer are 3.38–5.13% and 4.0% on average. It indicated that TOC contents at the bottom of the shale layer are smaller than the TOC contents at the top of the layer, suggesting that volcanic activity posed a long-term effect on biological growth. Seven different leachate concentrations were set in this experiment as follows: 1/10, 1/100, 1/500, 1/1000, 1/1500, 1/2000, and 1/2500. The results showed that the growth status of Pseudourostyla crassipes was affected by the addition of leachates with different concentrations compared to the control group. Additionally, the synthesis of chlorophyll a by Anabaena pseudoichthyoides was the most efficient with the 1/10 volcanic ash leachate. Through the analysis of major and trace elements in the solution before labeland after cultivation, the main elemental content of Ca2+, Mg2+, Na+, and K+ decreased by 3.8~87.24%, 75.96~92.70%, 86.56~95.67%, and 5.42~20.52% in the solution after microbial growth respectively. The trace elements B, Ba, Zn, and Fe decreased by 27.54~94.39%, 20~82.03%, 70.45~98.29%, and 99%. It was found that the B, Ba, Fe, and Zn elements decreased significantly. The nutrients from volcanic ash are the main factor promoting microbial growth. It can be indicated that the volcanic ash soaking solution has a higher content of nutrients when compared to the solubility of nutrients in volcanic ash compared to that of granite. A higher content of nutrients promotes microbial growth. The calculation results indicate that a volcanic eruption with a quantity of several 1010 m3 has a significant impact on microorganisms, lasting from tens of thousands to hundreds of thousands of years.

An H3O-alunite method for production of smelter grade alumina from an ammonium alum solution after high-pressure acid leaching of coal fly ash

Precipitation of H3O-alunite from an ammonium alum solution using boehmite as a seed was studied. The ammonium alum solution was obtained after high-pressure leaching of mullite-type coal fly ash (CFA) with a mixture of 7.5 M H2SO4 + 40% NH4HSO4 at 200 °C. Fe(III) was extracted from the ammonium alum solution by ion exchange sorption using the Purolite S957 resin. Effects of temperature (70–90 °C), seed boehmite (100–400 g/l), ammonium alum (60–240 g/l), and precipitation duration (2–8 h) on the Al precipitation degree were evaluated. Calcination of the precipitate at 300–950 °C to obtain alumina powder was studied next. Concentration of impurities, specific surface area, phase composition, morphology, and the average particle size distribution of alumina powders were investigated. The results show that smelter grade alumina (SGA) can be obtained at optimized parameters of precipitation and calcination.

Optimizing phosphorus precipitation from acidic sewage sludge ash leachate: Use of Mg-rich mining by-products for enhanced nutrient recovery

Phosphorus recovery from Sewage Sludge Ashes (SSA) by wet chemical extraction followed by selective precipitation has gained great attention in recent years, attempting to reduce the anthropic pressure on natural reserves. This study investigates the selective precipitation process at lab- and small pilot-scales by means of two conventional and one innovative precipitating agents, the latter derived from a low-grade magnesium oxide mining by-product (LG-MgO named PC8), assessing the role of the most relevant operating parameters. Lab-scale experiments were performed on leachates obtained from bottom and fly ashes, in which several operating conditions were tested, differing in the type of precipitating agent, target pH and nutrient molar ratio. Based on experimental results, small pilot-scale experiments were conducted with Ca(OH)2 and PC8 at pH 7. Effective phosphorus precipitation was obtained at lab-scale at pH equal to 4 for high Al/P molar ratio, while SSA leachate with low Al/P molar ratio promoted improved phosphorus precipitation (>90%) only at pH higher than 8 with PC8. Small pilot-scale findings confirmed the effectiveness of PC8 in increasing simultaneously the pH and the nutrient content of the solid precipitate. The comprehensive assessment of the samples denoted compliance with the European Regulation (EU 2019/1009), which allows the formulation of different fertilizers with agronomic relevance. This is the first time that experiments from small pilot-scale tests in the field of phosphorus recovery from SSA were investigated using an innovative precipitant providing key information for the process scale-up.

Experimental design and multiple response optimization of batch leaching tests of volcanic ashes.

Volcanic eruptions can release large amounts of tephra, lava, and gases, drawing attention due to their magnitude, energy, and impact on life and the environment. Among the most documented and sometimes dramatic effects of volcanic ashes are those linked to the input of diverse elements in the environment, which are released as a consequence of ash weathering. Laboratory studies have been conducted to investigate and predict the environmental input of chemical elements from volcanic ashes. This research paper describes the optimization of batch leaching tests used to investigate the release of ions from ashes collected in the Andes Cordillera after the eruption of the Puyehue volcano in 2011. Chemometric multivariate strategies were employed to evaluate the influence of variables affecting the leaching of volcanic ash. The effects of the main variables, namely contact time, the acidity of the leaching agent, the solid/liquid ratio, the particle size, and the stirring speed, were studied in leaching tests. To determine the optimal conditions for selected metal determinations, we employ Darringer's desirability function, which allows for the simultaneous optimization of the selected responses (element concentrations during the leaching process). Multielemental analysis (Na, Mg, Al, Si, P, Cl, K, Ca, V, Cr, Mn, Fe, Ni, Cu, Zn, Sr, Cd, Hg, Tl, and Pb) was quantified by ICP-MS (inductively coupled plasma-mass spectrometry) following adequate dilution of test leaching. These results established the optimal experimental conditions for leaching volcanic ash. The most significant variables were the solid/liquid ratio and the stirring speed, resulting in two groups of elements with an adequate global desirability function (D) value.

Selective separation and recovery of rare-earth elements (REEs) from acidic solutions and coal fly ash leachate by novel TODGA-Impregnated organosilica media

Rare-earth elements (REEs) are essential in a wide range of applications including magnets and satellite technology, with demand driven by geopolitical factors. While multiple techniques exist for REE recovery including solvent extraction and selective precipitation, solid–liquid extraction offers key advantages in selectivity, scalability, and recyclability. N, N, N′, N′-tetraoctyl diglycolamide (TODGA) is a tridentate ligand widely used in solvent extraction, but the incorporation in a solid support to separate individual lanthanides from acid solutions remains largely unexplored. A novel TODGA-organosilica sorbent material was developed and tested to evaluate recovery of 17 elements (REEs and thorium) in terms of selectivity, kinetics, and equilibrium isotherms in 0.01 to 15.9 M nitric acid. Characterization of the new sorbent was performed before and after sorption using FTIR, XPS, and SSA techniques to help elucidate sorption mechanisms and limiting variables. REE adsorption increased from 1.26 mg g−1 to 10 mg g−1 with nitric acid concentrations of 0.01 M and 15.9 M, respectively. TODGA-organosilica exhibits high selectivity towards heavy REEs (Dy to Lu), with minimal sorption of lighter REEs (Ce to Gd). Batch adsorption experiments confirm pseudo-second-order kinetics and a Langmuir adsorption isotherm with TODGA binding to REEs in a 3:1 complex. A packed bed column study confirmed the high selectivity of TODGA-impregnated organosilica towards heavy REEs and a proof-of concept experiment with coal fly ash leachate shows high selectivity for REEs over Al, Fe, and Ca present in several orders of magnitude higher concentrations. Fractionation was observed where loading cycle effluent contained 84 % light REEs while strip cycle effluent contained 80 % heavy REEs. More than 90 % of loaded REEs were successfully stripped with water as the stripping agent.

Acute and Chronic Ecotoxicity of Daphnia magna Exposed to Ash Leachate from the Cotopaxi Volcano, Ecuador.

Ecuador's wetlands and aquatic ecosystems are chronically exposed to ash contamination due to the frequent volcanoes' eruptions in the country. Still, the short and long-term effects of ash contamination on the aquatic biota are not well understood. We used ashes released by the Cotopaxi volcano in 2016 to investigate their acute and chronic effects in Daphna magna. We calculated the half maximal effective concentration (EC50) after 2 and 21 days of exposure, the non-observed effect concentration (NOEC), and the lowest observed effect concentration (LOEC) on offspring production. We also analyzed the metal concentration present in the ashes. The EC50 values at 2 and 21 days were found at 80% and 5% ash leachate concentrations, respectively. After 21 days of exposure, high mortality and low neonatal production were observed in all leachate concentrations (NOEC was at 15%, and LOEC was at 20% leachate concentration). Our results suggest that the ashes from the Cotopaxi volcano can cause acute and chronic toxicity to aquatic life and should be classified as hazardous waste, depending on the dose. There is an urgent need for further studies that assess toxicity caused by the intense volcanic activity in Ecuador.

Optimization of Culture Conditions for Microalgae Treatment Fly Ash Leachate System

In order to explore the feasibility of using algae to treat the fly ash leachate from a safe landfill site, leachate samples taken from a certain safe landfill site in Wenzhou City were treated with two different microalgae, Chlorella vulgaris and Scenedesmus obliquus, and the effectiveness of each treatment was evaluated in terms of its efficiency of pollutant removal. The effects of conditions such as pretreatment of leachate by sterilization, the initial concentration of leachate, and the addition of nutrients on pollutant removal efficiency and algae growth were studied. Sterilization of the leachate was found to have a relatively small impact on the growth of C. vulgaris and S. obliquus, as well as the removal of pollutants from the leachate. Therefore, sterilization treatment may not be necessary for engineering applications. Algal growth and the removal of pollutants were optimal when the leachate was used at a concentration of 10%, but when the leachate concentration was 30% or higher, the growth of both algae was weakened. The inclusion of 0.2 g/L K2HPO4·3H2O and 0.06 g/L ammonium ferric citrate in the system led to higher algal growth and pollutant removal. The chlorophyll a levels of C. vulgaris and S. obliquus were 555.53% and 265.15%, respectively, and the nitrogen removal rates were also the highest, reaching 59.51% and 56.69%, respectively. This study optimized the cultivation conditions of a microalgae treatment leachate system, providing technical support and a theoretical basis for the practical engineering of a harmless treatment of leachate.

CO2 mineralization and heavy metal leaching of multi-source ashes from municipal solid waste incineration

Mineralization holds great promise in simultaneously fixing CO2 and treating ash from the municipal solid waste incineration (MSWI). However, characteristics of CO2 mineralization and heavy metal leaching largely depends on the generation process of ashes. Herein, we report a systematic evaluation on the direct aqueous carbonation of multi-source MSWI ashes and leaching behavior of heavy metals before and after mineralization. Influencing factors for CO2 mineralization are determined to follow the order of CO2 concentration > temperature > solid–liquid ratio > stirring speed. Spray tower fly ash from the semi-dry process and bag filter fly ash from the dry process exhibit better sequestration capacities of 82.3 g-CO2/kg-ash and 150.9 g-CO2/kg-ash with a maximum CO2 removal rate of 0.117 mmol/s and 0.191 mmol/s among all ashes. Moreover, leaching concentration of Pb/Cu/As/Ni/Hg in six MSWI ashes all decreases significantly after CO2 mineralization. These findings could provide guidance for the potential intensive utilization of MSWI ashes in CO2 mitigation.

The Utilisation of Rice Husk Ash Leachates for The Synthesis of Eco-Friendly Geopolymers

Geopolymers are inorganic polymers projected as feasible alternatives to Portland cement due to their lower CO2 emissions and high mechanical properties. In recent times, however, their impact on other environmental indices such as abiotic depletion, freshwater toxicity, marine ecotoxicity, terrestrial ecotoxicity, acidification, and human toxicity has become questionable, thus the need to investigate alternative eco-friendly precursors and activators. This work aims to manufacture an eco-efficient geopolymer by utilising biomass ash leachate as an alternative to the conventional alkali silicate solution. The leachate was obtained by soaking the rice husk ash (RHA) in a 10 M concentration of NaOH solution and filtering to obtain a clear solution. The effects of the calcination temperature of the kaolin and the RHA content in the alkaline solution were investigated, and a factorial design of experiments was developed considering three levels of calcination temperature (700°C, 800°C, and 900°C) and five levels of RHA content (0 g, 5 g, 10 g, 15 g, and 20 g). Physical and mechanical tests were performed on the synthesised geopolymer pastes, and chemical analysis was performed using X-ray diffraction and X-ray spectroscopy. The impacts of replacing the synthetic alkali silicates with rice husk ash-based activators were compared. The results showed that the calcination temperature of the kaolin and the content of the RHA both contributed significantly to the flexural and compressive strength at the 0.01 level of significance. A compressive strength of 10.4 MPa was obtained for the MK915 binders, which showed a 100% increase from samples without RHA content. This research proves that utilising RHA-based activators in metakaolin-based geopolymers can be feasible for less critical applications where a very high compressive strength will not be required.Keywords: alkaline activators, biomass, geopolymers, leachates, rice husk ash

Coupled physicochemical dual-crosslinking Ti3C2Tx composite aerogels for the selective adsorption of gallium ions in acid fly ash leaching

Herein, in order to extract Ga3+ from acid fly ash leaching, we propose a functionalized Ti3C2Tx-based MXene composite aerogel adsorbent for Ga3+ adsorption. The prepared physicochemical dual-crosslinking network aerogel MPHG-40 possesses good Ga3+ adsorption performance (132.52 mg g−1) at the pH of 3 and Ga3+ initial concentration of 50 mg L−1 within 6 h. After five adsorption-desorption cycles, the material shows good mass retention and a 95.65 % retention of its initial adsorption capacity, compared to most reported adsorbents. The optimized adsorbent realized good selective adsorption of Ga3+ against Cu2+, Zn2+, Fe3+, and Al3+ in a simulated acid fly ash leaching with the selective coefficient of 8.63, 96.10, 4.49, and 28.30, respectively. The adsorption may comply with a combined mechanism of physical adsorption, electrostatic interactions, ion-exchange mechanism, and ligand chelation, dominated by chemical adsorption, as identified by theoretical calculations based on density functional theory and experimental data. The three-dimensional solid adsorbent constructed in this study provides a new strategy for selective adsorption of Ga3+, making it possible to be applied to solid waste utilization of fly ash.

Silica precipitation from rice husk ash leachate: optimization and kinetic analysis

Silica precipitation from rice husk ash leachate: optimization and kinetic analysis

Ash Properties and Environmental Impact of Coal and Its Blend with Patent Fuel for Climate Sustainability

Fossil fuels are still widely used today, and exploring more sustainable ways of using coal is crucial. One promising approach is to develop a patented fuel with reduced harmful gas emissions during combustion. This study aims to investigate the properties of the ash produced by burning steam coal mixed with various ratios of patent fuel. The combustion process was carried out using a standard solid fuel boiler with a power output of 70 kW. The ash samples were analyzed using various analytical methods, and ash leaching tests were conducted. The study found that adding patent fuel to coal affects combustion and ash composition. Determining the thermal stability of ash samples showed that adding patent fuel to coal results in decomposition starting earlier and in stronger combustion. The ash produced by patent fuel–coal mixtures contains lower concentrations of Ba, Cr, Ga, Li, Mn, V, and Zn than pure coal combustion. Leaching tests showed that coal ash leachates had higher concentrations of environmental pollutants, such as As, Cd, Co, Mn, Mo, Sb, and U, than patent fuel leachates. Adding patent fuel to coal affects combustion, ash properties, emissions, and disposal. Understanding these implications can help to develop sustainable coal usage and reduce environmental impact.

Improvement in Noodle Quality and Changes in Microstructure and Disulfide Bond Content through the Addition of Pepper Straw Ash Leachate.

Every year, a significant amount of pepper stalks are wasted due to low utilization. The ash produced from pepper stalks contains a significant amount of alkaline salts, which are food additives that can enhance the quality of noodles. Therefore, utilizing natural pepper straw ash to improve the quality of noodles shows promising development prospects. In this study, pepper straw ash leachate (PSAL) was extracted and added to noodles. The quality of the noodles gradually improved with the addition of PSAL, with the best effect observed at a concentration of 18% (PSAL mass/flour mass). This addition resulted in a 57.8% increase in noodle hardness, a 55.43% increase in chewiness, a 19.41% rise in water absorption rate, and a 13.28% increase in disulfide bond content. These alterations rendered the noodles more resilient during cooking, reducing their tendency to soften and thus enhancing chewiness and palatability. Incorporating PSAL also reduced cooking loss by 57.79%. Free sulfhydryl groups decreased by 5.1%, and scanning electron microscopy revealed a denser gluten network structure in the noodles, with more complete starch wrapping. This study significantly enhanced noodle quality and provided a new pathway for the application of pepper straw resources in the food industry.

Combustion Completeness and Sample Location Determine Wildfire Ash Leachate Chemistry

AbstractUnderstanding past fire regimes and how they vary with climate, human activity, and vegetation patterns is fundamental to the mitigation and management of changing fire regimes as anthropogenic climate change progresses. Ash‐derived trace elements and pyrogenic biomarkers from speleothems have recently been shown to record past fire activity in speleothems from both Australia and North America. This calls for an empirical study of ash geochemistry to aid the interpretation of speleothem palaeofire proxy records. Here we present analyses of leached ashes collected following fires in southwest and southeast Australia. We include a suite of inorganic elemental data from the water‐soluble fraction of ash as well as a selection of organic analytes (pyrogenic lipid biomarkers). We also present elemental data from leachates of soils collected from sites in southwest Australia. We demonstrate that the water‐soluble fraction of ash differs from the water‐soluble fraction of soils, with trace and minor element concentrations in ash leachates varying with combustion completeness (burn severity) and sample location. Changes in some lipid biomarker concentrations extracted from ashes may reflect burn severity. Our results contribute to building a process‐based understanding of how speleothem geochemistry may record fire frequency and severity, and suggest that more research is needed to understand the transport pathways for the inclusion of pyrogenic biomarkers in speleothems. Our results also demonstrate that potential contaminant loads from ashes are much higher than from soils, with implications for the management of karst catchments, which are a critical water resource.

Solidification and stabilization of heavy metals in medical waste ash through alkali activation

In the present work, medical waste ash was used as an aluminosilicate precursor to produce a geopolymer binder with stabilised heavy metals. The ash was initially calcined at a temperature of 800 °C for two hours to reduce the organic content. Calcined kaolin and medical waste ash were used as precursors to produce the geopolymer binder and sodium silicate and calcium oxides were used as alkaline activators. The effect of curing temperature (23, 60, and 100 °C) and the calcium oxide addition (0, 5, and 10%) on the geopolymer properties were evaluated. Eighteen geopolymer samples were prepared and evaluated for immobilizing heavy metals through the Toxicity Characteristic Leaching Procedure (TCLP). When compared to raw materials, TCLP results indicated that geopolymerization can significantly reduce the concentration of heavy metals in the medical waste ash leachate. The metal fixation percentages of the geopolymers ranged from 70 to 100%. The sequential extraction test results showed that geopolymerization (stabilization/solidification) is very beneficial in reducing the bioavailable fraction in the solid waste and maximizing the difficulty of fraction extraction.

Reactive Transport Modeling to Predict Leaching of Coal-Derived Fly Ash

Reactive Transport Modeling to Predict Leaching of Coal-Derived Fly Ash

Godzilla mineral dust and La Soufrière volcanic ash fallout immediately stimulate marine microbial phosphate uptake

During the “Godzilla” dust storm of June 2020, unusually high fluxes of mineral dust traveled across the Atlantic from the Sahara Desert, reaching the Caribbean Basin, Gulf Coast, and southeastern United States. Additionally, an eruption of the La Soufrière volcano on St. Vincent in April 2021 generated substantial ashfall in the southeastern Caribbean. While many studies have analyzed mineral dust’s ability to relieve nutrient limitation of phosphorus (P) in the P-stressed North Atlantic, less is known about the impact of extreme events and other natural aerosols on fluxes of P into seawater and from seawater into marine microbial cells. We quantified P and iron (Fe) content in mineral dust from the Godzilla dust storm and volcanic ash from the La Soufrière eruption collected at Ragged Point, Barbados. We also performed seawater incubations to assess the marine microbial response to aerosol deposition. Using environmentally-relevant concentrations of atmospheric particles for within the ocean’s mixed layer allowed us to draw realistic conclusions about how these deposition events impacted P cycling in situ. Volcanic ash has lower P content than mineral dust, and P in volcanic ash is far less soluble (~1%) than assumed in current atmospheric deposition models. Adding mineral dust and the volcanic ash leachate in concentrations representing different deposition scenarios increased soluble reactive phosphorus (SRP) concentrations in coastal seawater by ~7-32 nM. Phosphate uptake rate was stimulated in coastal seawater after either mineral dust or volcanic ash deposition at aerosol concentrations relevant to the Godzilla dust event, with ash eliciting the fastest uptake rate. Furthermore, high concentrations of both the mineral dust and volcanic ash led to slightly elevated alkaline phosphatase activity (APA) compared to the relevant controls, indicating higher potential for use of dissolved organic phosphorus (DOP) as a P source. Quantifying these aerosols’ impacts on P cycling is a significant step towards achieving a better understanding of their potential roles in relieving nutrient limitation and fueling the biological carbon pump.

Efficient recovery of aluminum, lithium, iron and gallium from coal fly ash leachate via coextraction and stepwise stripping

The recovery of critical metals from industrial waste is very important and challenging. This work proposed an efficient process for recovering aluminum, lithium, iron and gallium from coal fly ash leachate. Firstly, 98.1 %, 86.6 % and 99.8 % of iron, lithium and gallium are coextracted by tributyl phosphate (TBP), facilitating the subsequent use of the aluminum raffinate. The spectroscopic analysis verifies the formation of [Li(TBP)2][FeCl4] and [Li(TBP)2][GaCl4]. Afterwards, the effective separation of lithium, iron, gallium in TBP is achieved by stepwise stripping. Lithium can be almost completely stripped using 6 mol/L HCl with free iron and gallium of loss. An extremely high separation factor of iron and gallium (αFe/Ga, 1175) can be achieved through reduction stripping by precisely controlling pH value and oxidation–reduction potential. Finally, about 99.5 % of gallium can be stripped with 0 ∼ 1 mol/L HCl. This work realizes the synergistic recovery of valuable metals from waste resources.

Hydraulic conductivity of geosynthetic clay liners to trona ash leachate: Effects of mass per unit area, bundles of fiber existence, and preydration conditions

The barrier performance of geosynthetic clay liners (GCLs) to coal combustion products (CCPs) is of primary importance. One of the CCPs leachates that has a damaging effect on hydraulic conductivity is trona ash leachate (TAL). In this study, the hydraulic conductivity of sodium GCL (Na-GCL) to TAL was investigated in terms of mass per unit area (MPUA). The hydraulic conductivity of GCLs to TAL was 2.6 × 10-6 and 7.6 × 10-7 m/s when the MPUA was 3.0 kg/m2 (Mb3) and 4.0 kg/m2 (Mb4), respectively. Dye tests conducted on these GCLs showed that flow preferentially occurred through bundles of fibers existing in the GCLs. In contrast, increasing the MPUA to 5.0 kg/m2 (Mb5) led to a decrease in the hydraulic conductivity (i.e. 4.1 × 10-11 m/s). Additional tests were performed on fiber-free GCLs to determine the role of fiber bundles. Regardless of MPUA, the fiber-free GCLs had low hydraulic conductivity (6.7 × 10-11 m/s). Prehydrating Mb3 and Mb4 with deionized water (DIW) before permeation with TAL also decreased the hydraulic conductivity. The hydraulic conductivities of prehydrated Mb3 and Mb4 were 1.6 × 10-10 and 4.8 × 10-11, respectively. Chemical analyses showed that the cation exchange reaction had a negligible influence on the hydraulic conductivity. Because TAL was a potential source of Na+ throughout the tests.