Anoxic-oxic Membrane Bioreactor Research Articles

Optimization of step-feed anoxic-oxic-membrane bioreactor (AO-MBR) with methanol addition for biological nitrogen removal in wastewater using BioWin and response surface methodology (RSM)

The study optimized a step-feed anoxic-oxic membrane bioreactor (AO-MBR) with methanol addition, an existing biological nitrogen removal (BNR) process, to improve total nitrogen (TN) removal and to reduce operating costs. Methanol, utilized as an external carbon source, was costly, which led to examining ways to reduce its usage by adjusting the operational parameters and modifying the configuration. The BioWin’s built-in activated sludge model underwent calibration through biokinetic batch experiments and numerical adjustments of stoichiometric and kinetic parameters to create the BNR process model. Dynamic simulations validated the calibrated model. Using the model, a modified configuration with a 20.8% increase in total anoxic volume was proposed. This increased the anoxic hydraulic retention time, improving the denitrification process. The response surface methodology (RSM) was then used to optimize the operating parameters of the modified configuration for maximum TN removal efficiency and minimum operating cost. The optimized parameters found were 0.5 mg/L dissolved oxygen, 45 days of solid retention time, 0:1 methanol distribution ratio, and 1,794.29 L/d methanol, which all enhanced the denitrification process. This resulted in a 16% increase in TN removal efficiency, a 4.12% decrease in operating costs, and an 8.96% reduction in methanol usage.

Effects of solid retention time and exposure mode to electric current on Remazol Brilliant Violet removal in an electro-membrane bioreactor.

The performance of an electrochemically assisted anoxic-oxic membrane bioreactor (A/O-eMBR) was assessed as an alternative for azo dye (Remazol Brilhant Violet (RBV)) removal from simulated textile wastewater. The A/O-eMBR was operated under three experimental conditions (runs I, II, and III), in which different solids retention time (SRT) (45 and 20 d) and exposure mode to electric current (6'ON/30'OFF and 6'ON/12'OFF) were assessed. The reactor exhibited excellent decolorization performance for all runs, with average dye removal efficiency ranging from 94.3 to 98.2%. Activity batch assays showed that the dye removal rate (DRR) decreased from 16.8 to 10.2mg RBV L-1h-1 when the SRT was reduced from 45 to 20 d, likely attributed to the lower biomass content under lower sludge age. At the electric current exposure mode of 6' ON/12'OFF, a more substantial decrease of DRR to 1.5mg RBV L-1h-1 was noticed, suggesting a possible inhibitory effect on dye removal via biodegradation. By reducing the SRT to 20 d, a worse mixed liquor filterability condition was observed, with a membrane fouling rate (MFR) of 0.979kPa d-1. In contrast, using the electric current exposure mode of 6'ON/12'OFF resulted in lower membrane fouling propensity, with an MFR of 0.333kPa d-1. A more attractive cost-benefit ratio for dye removal was obtained using the exposure mode of 6'ON/30'OFF, for which the energy demand was estimated at 21.9-22.6 kWh kg dye-1 removed, almost two times lower than that observed for the mode of 6'ON/12'OFF.

Characterization and Disinfection by Product Formation of Dissolved Organic Matter in Anaerobic–Anoxic–Oxic Membrane Bioreactor (AAO-MBR) Process

In the process of sewage treatment, the characteristics of dissolved organic matter (DOM) are always changed during chemical and biological processes, affecting the generation of disinfection by-products (DBPs) compositions at the following disinfection stage. The present study systematically investigated the effect of DOM characterization on C- and N-DBPs formation at AAO-MBR reactor when treating wastewater. The results showed that the AAO-MBR treatment process could efficiently eliminate dissolved organic carbon (DOC) and ammonium nitrogen (NH4+-N) from wastewater with an elimination rate of 89% and 98%, respectively. Most of the precursors (i.e., 56.8% C-DBPs and 78.1% N-DBPs) were removed at the MBR unit, while AGC and AAO units promoted the formation of DBPs precursors. More specifically, soluble microbial products (SMPs) and humus acid were increased, which led to improved C- and N-DBPs via aerated grit chamber (AGC) treatment. At the AAO treatment unit, the content of low MW hydrophobic SMPs, humus acid, and polysaccharides was increased, indicating low MW and HPO fractions dominating the C- and N-DBPs. MBR treatment improved C-DBPs in high MW and HPO fractions and N-DBPs in low MW and HPO fractions, which is explained by higher MW hydrophobic SMPs and humus acids, compared to the AAO unit. The present study provided deep insight into the linkage of DOM characteristics and C- and N-DBPs formation at each treatment unit during the AAO-MBR process.

Post-treatment of matured landfill leachate: Synthesis and evaluation of chitosan biomaterial based derivatives as adsorbents

Matured landfill leachate is complex in nature, hence, a single conventional treatment unit is insufficient to remove the contaminants of the leachate to achieve the discharge standards. Furthermore, high levels of organic matter, colour compounds, and iron-based materials form a dark black/brown colour in leachate which is not removed by the biological treatment units. Hence, an Anoxic-Oxic Membrane Bioreactor coupled with a tertiary adsorption unit composed of crosslinked-protonated chitosan was tested for effective removal of the colour of the permeate. Several operational parameters such a pH, contact time, and adsorbent dosage on the adsorptive removal of colour were quantified using sorption-desorption experiments. Furthermore, the biosorbent was characterized using FTIR, SEM, XRD, BET-specific surface area, and pHZPC. Response Surface analysis confirmed the optimization of operational parameters conducted through traditional batch experiments. Langmuir isotherm model fitted with equilibrium data (R2 = 0.979) indicating a monolayer homogeneous adsorption. Kinetic data followed the Pseudo-Second-Order model (R2 = 0.9861), showing that the adsorbent material has abundant active sites. The percentage removal values show that the colour removal increases with time of contact and dosage of adsorbent, but removal is mainly influenced by the solution pH levels. The experimental results manifested a colour removal efficiency of 96 ± 3.8% obtained at optimum conditions (pH = 2, adsorbent dosage = 20 g/L, contact time = 48 h) along with an adsorption capacity of 123.8 Pt–Co/g suggesting that the studied adsorbent can be used as an environmentally friendly biosorbent in a tertiary unit for colour removal in a treatment system which is used to treat matured landfill leachate.

Characterization of Microbial Communities in Wastewater Treatment Plants Containing Heavy Metals Located in Chemical Industrial Zones.

Water pollution caused by heavy metals (HMs) poses a serious risk to human health and the environment and can increase the risk of diabetes, cancer, and hypertension in particular. In this study, two full-scale wastewater treatment plants (WWTPs) in industrial zones in southern China were selected to analyze the microbial community structure, diversity, similarity, and differentiation in the anoxic/oxic (AO) and anoxic/oxic membrane bioreactor (AO-MBR) units under the stress of HMs. High-throughput sequencing showed that microbial diversity and abundance were higher in the AO process than in the AO-MBR process. In the two WWTPs, the common dominant phyla were Proteobacteria and Bacteroidetes, while the common dominant genera were Gemmatimonadaceae, Anaerolineaceae, Saprospiraceae, and Terrimonas. Manganese (Mn) and zinc (Zn) positively correlated with Saccharimonadales, Nakamurella, Micrococcales, and Microtrichales, whereas copper (Cu) and iron (Fe) positively correlated with Longilinea and Ferruginibacter. Additionally, the relative abundances of Chloroflexi, Patescibacteria, and Firmicutes differed significantly (p < 0.05) between the two processes. These results may provide comprehensive outlooks on the characterization of microbial communities in WWTPs, which could also help to reduce the potential environmental risks of the effluent from WWTPs located in industrial zones.

Elucidating the intensifying effect of introducing influent to an anaerobic side-stream reactor on sludge reduction of the coupled membrane bioreactors

Three anoxic/oxic membrane bioreactors (AO-MBRs) coupled with the anaerobic side-stream reactor (ASSR) with different influent flow distribution ratios (IFDRs) were assessed to elucidate how IFDR in the ASSR affected pollutants removal, sludge reduction, membrane fouling, and potential co-occurrence network of microorganisms. When the IFDR in the ASSR was increased from 0% (ASSR0-MBR), to 25% (ASSR25-MBR) and 75% (ASSR75-MBR), chemical oxygen demand removal was enhanced and nutrient removal was comparable. Compared to ASSR0-MBR, ASSR25- and ASSR75-MBR further improved the sludge reduction by 7.6% and 10.9%, respectively. ASSR25-MBR followed cake-complete model due to the weak membrane surface scouring and high concentration of extracellular polymeric substances, while ASSR0- and ASSR75-MBR fitted cake-standard model. The increased IFDR in the ASSR boosted the relative abundance of hydrolytic and slow-growing bacteria. The co-occurrence networks of sludge reduction, nutrient removal and membrane fouling propensity indicated that the symbiotic relationships were dominant.

Unraveling membrane fouling in anoxic/oxic membrane bioreactors treating anaerobically digested piggery wastewater

Anaerobically digested piggery wastewater (ADPW) draws increasing attention due to the high nitrogen and carbon level. In this study, four parallel lab-scale anoxic-oxic membrane bioreactors were applied to treat ADPW with the hydraulic retention time (HRT) of 75, 60, 45 and 30 h, respectively. Reactor performance and membrane fouling mechanisms also have been systematically evaluated. The results demonstrated a decline in chemical oxygen demand and total nitrogen biodegradation (from 65.8 ± 2.5% and 62.2 ± 5.5% to 38.6 ± 3.6% and 26.2 ± 5.7%, respectively) and a rise in membrane resistance (from 37.34 × 1012 m−1 to 51.69 × 1012 m−1) as the HRT decreased. The decline of HRT didn’t affect the functional group types of cake layer extracellular polymeric substances (EPS) and tightly bound EPS (TB-EPS) of activated sludge, but led to the increased concentrations of protein (PN) and polysaccharide (PS) in loosely bound EPS (LB-EPS) and soluble microbial products (SMP) of activated sludge and a decreased PN/PS ratio in SMP. These changes in SMP and EPS accelerated the formation of cake layer and aggravated the membrane fouling. Proteobacteria and Bacteroidetes were the predominant phyla on membrane surface. The abundant Proteobacteria in the reactor with longer HRTs was beneficial to mitigate membrane fouling while the relative abundance of Bacteroidetes remained stable in all reactors. The enrichment of Thauera was the primary reason for membrane fouling at genus level in the reactors. This study provides scientific insights on the practical application of membrane bioreactors in terms of membrane fouling control.

Performance and Microbial Community of Different Biofilm Membrane Bioreactors Treating Antibiotic-Containing Synthetic Mariculture Wastewater.

The performance of pollutant removals, tetracycline (TC) and norfloxacin (NOR) removals, membrane fouling mitigation and the microbial community of three Anoxic/Oxic membrane bioreactors (AO-MBRs), including a moving bed biofilm MBR (MBRa), a fixed biofilm MBR (MBRb) and an AO-MBR (MBRc) for control, were compared in treating antibiotic-containing synthetic mariculture wastewater. The results showed that MBRb had the best effect on antibiotic removal and membrane fouling mitigation compared to the other two bioreactors. The maximum removal rate of TC reached 91.65% and the maximum removal rate of NOR reached 45.46% in MBRb. The addition of antibiotics had little effect on the removal of chemical oxygen demand (COD) and ammonia nitrogen (NH4+-N)—both maintained more than 90% removal rate during the entire operation. High-throughput sequencing demonstrated that TC and NOR resulted in a significant decrease in the microbial diversity and the microbial richness MBRs. Flavobacteriia, Firmicutes and Azoarcus, regarded as drug-resistant bacteria, might play a crucial part in the removal of antibiotics. In addition, the dynamics of microbial community had a great change, which included the accumulation of resistant microorganisms and the gradual reduction or disappearance of other microorganisms under antibiotic pressure. The research provides an insight into the antibiotic-containing mariculture wastewater treatment and has certain reference value.

Understanding mechanisms of sludge in situ reduction in anaerobic side-stream reactor coupled membrane bioreactors packed with carriers at different filling fractions

An anoxic/oxic membrane bioreactor (AO) and three pilot-scale anaerobic side stream reactors (ASSR) coupled MBRs (ASSR-MBRs), packed with 0%, 25% and 50% carriers in ASSRs, were continuously operated to study the mechanisms for sludge reduction. Four systems showed efficient COD and NH4+-N removal, while packing carriers significantly enhanced nitrogen removal. 25% filling fraction (AP25) achieved the highest sludge reduction efficiency of 50.5% compared to 0% (21.7%) and 50% (39.7%). Compared to ASSR-MBR, carriers enhanced the release of dissolved organic matters, and accelerated the secretion of enzyme for cell lysis and hydrolysis. In AP25, the presence of carriers prompted the formation of environment propitious to sludge reduction in bulk sludge. AP25 tended to enrich hydrolytic, fermentative and denitrifying bacteria to accelerate hydrolysis process, while excessive carriers had negative effect on biomass stability and movement of carriers.

Effects of bioporous carriers on the performance and microbial community structure in side-stream anaerobic membrane bioreactors.

The aim of this study was to investigate the effects of a volcanic rock porous carrier (VRPC) on sludge reduction, pollutant removal, and microbial community structure in an anaerobic side-stream reactor (ASSR). Three lab-scale membrane bioreactors (MBRs), including an anoxic-oxic MBR, which served as the control (C-MBR), an ASSR-coupled MBR (A-MBR), and an A-MBR filled with VRPC (FA-MBR) were stably and simultaneously operated for 120 days. The effect of the three reactors on the removal of chemical oxygen demand (COD) was almost negligible (all greater than 95%), but the average removal efficiency of ammonium nitrogen, total nitrogen, and total phosphorus was significantly improved by the insertion of an ASSR, especially when the ASSR was filled with VRPC. Finally, A-MBR and FA-MBR achieved 16.2% and 26.4% sludge reduction rates, with observed sludge yields of 0.124 and 0.109 g mixed liquid suspended solids/g COD, respectively. Illumina MiSeq sequencing revealed that microbial diversity and richness were highest in the VRPC, indicating that a large number of microorganisms formed on the carrier surface in the form of a biofilm. Abundant denitrifying bacteria (Azospira, Comamonadaceae_unclassified, and Flavobacterium) were immobilized on the carrier biofilm, which contributed to increased nitrogen removal. The addition of a VRPC to the ASSR successfully immobilized abundant hydrolytic, fermentative, and slow-growing microorganisms, which all contributed to reductions in sludge yield.

Assessing inorganic components of cake layer in A/O membrane bioreactor for physical-chemical treated tannery effluent

In this study, an anoxic-oxic membrane bioreactor (A/O-MBR), was used to treat effluent tannery wastewater pretreated by physicochemical processes. The A/O-MBR performed well during the experimental period and was able to produce a high-quality effluent containing 90 ± 10 mg-CODcr/L and 0.5 ± 0.1 mg-NH4+-N/L. However, it was observed that at rates of approximately 1.02 kPa/day and 1.2 μm/day, both transmembrane pressure (TMP) and thickness of cake layer increased during wastewater treatment. The eventual thickness of the cake layer was between 47.8 and 51.5 μm. Furthermore, an Inductively Coupled Plasma-Optical Emission Spectrometer, used to analyze inorganic components of the cake layer, revealed that four inorganic elements, Cr, Ca, Mg and Al were predominant (weight percentage rate 4:13:10:72). Due to low solubility (Cr(OH)3: Ksp 6.3 × 10−31; Al(OH)3: Ksp 6.3 × 10−19), the elements of Cr and Al mainly existed in the forms of Cr(OH)3 and Al(OH)3, respectively. Other minerals in the cake layer included Al2O3, CaCO3, and MgCO3. Additionally, using an SEM-EDX (Scanning electron microscopy-energy dispersive X-ray analyzer), we discovered that inorganic particles that formed within the activated sludge of the A/O-MBR steadily accumulating on the membrane surface, resulted in an evenly distributed inorganic layer which could be observed along the cross-sections of the cake layer.

Evaluating influence of filling fraction of carriers packed in anaerobic side-stream reactors on membrane fouling and microbial community of the coupled membrane bioreactors

An anoxic/oxic membrane bioreactors (AO-MBR) and three identical anaerobic side-stream reactor coupled with anoxic/oxic membrane bioreactors (ASSR-MBR) were constructed and operated in parallel to investigate the appropriate filling fraction of carriers packed in ASSR, influences on pollutants removal, sludge reduction, membrane fouling and microbial community of ASSR-MBR. Inserting ASSR achieved efficient COD removal and nitrification, and packing carriers in ASSR obtained the highest sludge reduction efficiency of 50.5 % at filling fraction of 25 %. Compared to AO-MBR, inserting ASSR without carriers induced the release of viscous components in extracellular polymeric substances (EPS) and the formation of calcium carbonate-related bacteria on membrane surface, and thus deteriorated membrane fouling. Packing carriers with 25 % filling fraction promoted the hydrolysis of soluble microbial products and EPS, whilst reduced the viscoelasticity of sludge flocs. Higher filling fraction of 50 % increased the shear forces to the biofilm and biomarkers related to membrane fouling, and thus showed little improvement to alleviate membrane fouling. MiSeq sequencing revealed that although it enriched in the bulk sludge of conventional ASSR-MBR and the coupled reactor with filling fraction of 50 %, the floc-forming, hydrolytic and fermentative bacteria were more inclined to attach on the membrane surface and alleviate fouling process.

A simple way to improve a conventional A/O-MBR for high simultaneous carbon and nutrient removal from synthetic municipal wastewater.

In this study, two anoxic-oxic membrane bioreactor (A/O-MBR) systems, i.e. conventional and biofilm anoxic-oxic-membrane bioreactors (C-A/O-MBR and BF-A/O-MBR, respectively), were operated in parallel under conditions of complete sludge retention for the purposes of comparing system performance and microbial community composition. Moreover, with the microbial communities, comparisons were made between the adhesive stage and the suspended stage. High average removal of COD, NH4+-N and TN was achieved in both systems. However, TP removal efficiency was remarkably higher in BF-A/O-MBR when compared with C-A/O-MBR. TP mass balance analysis suggested that under complete sludge retention, polyurethane sponges that were added into the anoxic tank played a key role in both phosphorus release and accumulation. The qPCR analysis showed that sponge biomass could maintain a higher level of abundance of total bacteria than the suspended sludge. Meanwhile, AOB and denitrifiers were enriched in the suspended sludge but not in the sponge biomass. Results of illumina sequencing reveal that the compacted sponge in BF-A/O-MBR could promote the growth of bacteria involved in nutrient removal and reduce the amount of filamentous and bacterial growth that is related to membrane fouling in the suspended sludge.

Effects of quorum quenching on temporal succession of activated sludge microbial community in a membrane bioreactor.

Quorum quenching (QQ) is an attractive strategy for mitigating biofouling in membrane bioreactors (MBRs). However, the effects of QQ on the activated sludge (AS) process have not been adequately evaluated. This study investigated the long-term effects of QQ on a laboratory-scale anoxic-oxic MBR, focusing on AS performance and microbial community. Anoxic-oxic MBRs with and without QQ were operated for 91days. QQ did not affect COD and TN removal efficiencies over the experimental period, during which its activity remained >90%. QQ reduced floc size by approximately 8% but had no effect on biomass concentration. AS microbial communities were regularly analysed using massively parallel sequencing. AS bacterial communities were temporally dynamic irrespective of QQ presence, for example, a temporal increase in bacterial diversity and a temporal decay of community similarity. QQ counteracted the temporal change in diversity and the temporal distance-community decay. Community comparison revealed that QQ changed the successional trajectory of the AS community at a late period, because it decelerated temporal changes of specific members, such as Thiothrix and Sphingomonadaceae*. Correlation networks revealed that QQ increased network clustering, complexity and density. The combined results suggest that the tighter microbial association by QQ increased the community resistance. QQ can enhance the diversity and stability of the AS community in MBR by counteracting the innate temporal change in community structure. Our findings are useful for the further advancement of QQ-based strategies in engineered microbial environments.

Controlling sludge retention time to alleviate inhibition of nitrosation and nitration by accumulated aluminum in an A/O-MBR

Severe membrane fouling and limited effect of biological phosphorus removal are the major drawbacks for anoxic-oxic membrane bioreactor (A/O-MBR). The dosing of poly-aluminum chloride in A/O-MBR can reduce membrane fouling and improve phosphorus removal certainly, but it may bring potential impacts on the specific oxygen uptake rate of sludge and the activity of ammonia-oxidizing bacteria and nitrite-oxidizing bacteria with accumulated aluminum. Controlling sludge retention time (SRT) was firstly investigated to evaluate the effect on alleviating inhibition caused by accumulated aluminum in A/O-MBR. As compared to the performance without dosing of poly-aluminum chloride, the effluent ammonia concentration in the SRT-15d reactor was increased by 91.80% lower than that of SRT-30d reactor (111.84%). Due to higher sludge yield rate in the SRT-15d reactor, the amount of accumulated aluminum was 39.33 mg Al g−1 VSS less than that of the SRT-30d reactor. Besides, the decline of the activity of ammonia-oxidizing bacteria and nitrite-oxidizing bacteria in the SRT-15d reactor was 4.4% and 18.3%, respectively lower than that of the SRT-30d reactor. Therefore, controlling shorter SRT can be used as an effective tool to alleviate inhibition of nitration and nitrosation by accumulated aluminum in A/O-MBR.

Influence of aluminium accumulation on biological nitrification and phosphorus removal in an anoxic-oxic membrane bioreactor.

Poly-aluminium chloride (PAC) is often used to enhance phosphorus removal and control membrane fouling in membrane bioreactors (MBRs). However, the influence of aluminium accumulation on the biological nitrification and phosphorus removal of MBRs has not been well assessed. In the present study, the effects of accumulated aluminium on sludge activity and morphology were investigated in a lab-scale anoxic-oxic membrane bioreactor. The reasonably high removal efficiencies of NH4+-N, TN, and COD, i.e. 94.9%, 84.8%, and 92.8%, respectively, were achieved in the reactor when the percentage of atomic aluminium on sludge surface increased to 14.2%. However, the decreases in the ammonia oxidation rate, nitrite oxidation rate, and specific oxygen uptake rate of sludge by 82.1%, 79.8%, and 46.4%, respectively, were observed. Meanwhile, the activity of phosphate-accumulating organisms was completely inhibited. Furthermore, the protein content in the extracellular polymeric substances of sludge decreased substantially, and the sludge became more dispersed due to the alum accumulation, compared with that of the initial phase. Therefore, long-term dosing of PAC in the MBR should be managed to avoid excessive aluminium accumulation in the sludge.

Identifying microbial community evolution in membrane bioreactors coupled with anaerobic side-stream reactor, packing carriers and ultrasonication for sludge reduction by linear discriminant analysis

An anoxic/oxic membrane bioreactor (AO-MBR), an anaerobic side-stream reactor (ASSR) coupled MBRs (A-MBRs), an A-MBR with carriers packed in ASSR (AP-MBR) and an AP-MBR with sludge ultrasonicated before ASSR (AUP-MBR) were operated for 261 d to investigate effects of ASSR, packing carriers and ultrasonication on sludge reduction and microbial population. Sludge reduction efficiencies of A-MBR, AP-MBR and AUP-MBR were 36.2%, 46.4% and 51.4%, respectively. Packing carriers and ultrasonication both enhanced hydrolysis by stimulating activities of α-glucosidase and protease, while uncoupling metabolism was enhanced greatly by packing carriers but slightly by ultrasonication. Linear discriminant analysis of effect size (LEfSe) results showed that packing carriers promoted the growth of hydrolytic and fermentative bacteria in bulk sludge, and enriched anaerobes and fermentative bacteria on the surface of carriers. Ultrasonication screened ultrasonication-resistant bacteria, and created an anaerobic environment beneficial to hydrolytic and fermentative bacteria.

Effects of hydraulic retention time on process performance of anaerobic side-stream reactor coupled membrane bioreactors: Kinetic model, sludge reduction mechanism and microbial community structures

An anoxic/oxic membrane bioreactor (AO-MBR) and three anaerobic side-stream reactor (ASSR) coupled MBRs (ASSR-MBR) were operated to investigate the effects of hydraulic retention time of ASSR (HRTA) and to elucidate sludge reduction mechanisms in ASSR-MBRs. Increasing HRTA from 3.3 to 6.6 h improved nitrogen removal, and enhanced sludge reduction from 8.0% to 40.9% in ASSR-MBR. The sludge decay coefficient was 0.0221 d−1 in MBRs, and 0.0231–0.0345 d−1 in ASSRs. The measured lysis rate coefficient of heterotrophic biomass was 0.083–0.112 d−1 in MBRs and 0.079–0.111 d−1 in ASSRs. The hydrolysis rate coefficient of inactive particulate organic matters (POMs) in ASSRs significantly exceeded that in the MBR. At HRTA of 6.6 h, POMs hydrolysis in ASSR (38.6%) is the dominant route of sludge reduction, and cell lysis occurred principally in aerobic tanks. Illumina-MiSeq sequencing showed ASSR-MBRs enriched hydrolytic and fermentative bacteria, and confirmed that anaerobic hydrolysis contributed most to sludge reduction.

Integrated interrogation of causes of membrane fouling in a pilot-scale anoxic-oxic membrane bioreactor treating oil refinery wastewater

Studies on membrane fouling during treatment of oil refinery wastewater (ORW) via membrane bioreactor (MBR) are currently lacking, and associated fouling challenges are largely undocumented. Using advanced chemical and Illumina sequencing approach, we investigated the complex bio-physiochemical interactions responsible for foulant-membrane interactions during treatment of ORW. After nearly 2 months of the MBR operation, COD removal reached maximal of 97.15 ± 1.85%, while oil and grease removal was maintained at 96.6 ± 2.6%, during the treatment duration. Most of the less or non-biodegradable oil moieties (>0.5 μm) progressively accumulated on the membrane as the influent oil concentration increased. Presence of relatively higher unsaturated extracellular polymers (100.6 mg/g VSS) like fulvic acid and aromatic-like compounds at high volumetric loading (~18.7 kg COD/m3/d), enhanced the adsorption of chemical elements (Fe = 88.9, Al = 63.4, and Ce = 0.56 mg/g dry-sludge, respectively). Moreover, shift in microbial community structure to hydrocarbon-utilizing and metals-tolerating genera, as Comamonas and Rhodanobacter, respectively, uncovers major membrane colonizers in ORW treatment via MBR.

Correlation of microbial community structure with pollutants removal, sludge reduction and sludge characteristics in micro-aerobic side-stream reactor coupled membrane bioreactors under different hydraulic retention times

A micro-aerobic side-stream reactor (MSSR) was inserted in returned sludge line of a membrane bioreactor (MBR) for sludge reduction. Three MSSR coupled MBRs (M-MBRs) and an anoxic/oxic MBR (AO-MBR) were operated in parallel to investigate effects of micro-aerobic condition and hydraulic retention time (HRT) of MSSR (HRTM) on process performance. M-MBRs and AO-MBR were equally effective in COD and NH4-N removal. Rising HRTM from 3.3 to 6.7 h increased sludge reduction from 10.8% to 47.5%, and promoted dissolved organic matters release and utilization by enriching hydrolytic, fermentative and predatory bacteria. M-MBR at HRTM of 3.3 h obtained the highest nitrogen removal, and enriched denitrifiers (Thauera and Hyphomicrobium) in the MSSR. The highest relative abundance of polyphosphate-accumulating organisms was observed in M-MBR at HRTM of 5.0 h, which achieved the highest phosphorus removal. Prolonging HRTM to 6.7 h improved sludge dewaterability by enriching floc-formation bacteria (Nannocystis) and inhibiting filamentous bacteria (Candidatus_Alysiosphaera).