Anode Material For Lithium-ion Batteries Research Articles

Cu@MOF based composite materials: High performance anode electrodes for lithium-ion and sodium-ion batteries

In order to satisfy the increasing demand for energy, it is essential to improve the efficiency of lithium-ion batteries (LIBs) and sodium-ion batteries (SIBs) batteries. Metal selenides (MSes) have a high theoretical specific capacity, can be designed in a variety of ways, conduct electricity well, can change morphology easily, and have a multi-electron reaction mechanism. These characteristics make them very competitive as anode materials for LIBs and SIBs. Herein, we synthesise Cu@MOF and Cu@NH2-MOF as the precursor to prepare Cu1.95Se embedded into porous carbon matrix (Cu1.95Se@PC) and porous-N-doped carbon matrix (Cu1.95Se@NPC) via pyrolysis process of Cu@MOF and Cu@NH2-MOF, respectively. Cu1.95Se@PC and Cu1.95Se@NPC electrodes for half-cell LIBs and SIBs exhibit a high reversible capacity of 313.1, 480.9 (for LIBs), 216.3 and 303.8 (for SIBs) mAhg−1after 1000 cycles at 2 A g−1, respectively. We assess the electrochemical performance of the Cu1.95Se@PC and Cu1.95Se@NPC anodes by integrating them with commercially available LiFePO4 (LFP) into full-cell LIBs. The LFP//Cu1.95Se@PC and LFP//Cu1.95Se@NPC full-cells have discharge capacities of approximately 330 and 293 mAh g−1 at 0.3 A g−1 at the initial cycle. In order to explore the sodium storage mechanism of the Cu1.95Se composites, we conducted an in situ XRD test during the first charge/discharge cycle, considering their favourable cycling and rate performance. Our work provides a promising anode electrode material for both half-cell LIBs and SIBs with high volume utilization and superior electrochemical performances.

Hierarchical porous silicon oxycarbide as a stable anode material for lithium-ion batteries

Hierarchical porous silicon oxycarbide as a stable anode material for lithium-ion batteries

The Effect of Nickel Addition on α-Fe2O3 Synthesis Using NaOH and Application as Lithium-Ion Battery Anode Material

Research has been conducted in the pursuit of developing the performance of batteries. The increasing demand for electronic devices and electric vehicles has driven the development of high-performance lithium-ion batteries (LIBs). Among the various anode materials, α-Fe2O3 has attracted significant attention due to its high theoretical specific capacity of 1007 mAh/g. However, its low conductivity and poor rate capability limit its practical application. To address these issues, this study investigates the addition of nickel (Ni) into α-Fe2O3 through a co-precipitation method. The synthesized materials were characterized using Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), and Scanning Electron Microscopy with Energy-Dispersive X-ray spectroscopy (SEM-EDX). The electrochemical performance was evaluated using an LCR meter and charge-discharge cycling. The results showed the addition of Ni improved the conductivity of the α-Fe2O3 material. The optimal Ni content was found as much as 18×10-4 mol which exhibits the highest conductivity and specific capacity. The synthesized α-Fe1.965Ni0.035O3 material demonstrated a specific charging capacity of 1.8433 mAh/g and a specific discharging capacity of 1.8388 mAh/g. These findings suggest that Ni-doped α-Fe2O3 has the potential to be a promising anode material for high-performance lithium-ion batteries (LIBs).

Chromium Oxide Nanoparticles Anchored in Hydrogel-Derived Three-Dimensional N-Doped Porous Carbon Anode Materials as Lithium-Ion Batteries.

Transition metal oxides (TMOs) have been identified as the most promising anode materials for lithium-ion batteries (LIBs). However, these materials tend to undergo volumetric expansion during battery operation, which disrupts their internal structure and ultimately leads to a degradation of battery performance. Cr2O3/N-doped porous carbon (Cr2O3@NC) composites were successfully synthesized through high-temperature calcination using Cr2O3-containing hydrogels as precursors. The results show that the carbon material not only improves the electron transfer ability of Cr2O3 but also effectively prevents its agglomeration. The Cr2O3@CN composite as a novel anode material for LIBs exhibits a reversible capacity of 936 mAh g-1 after 200 cycles at a current density of 1 A g-1, showcasing excellent cycling and structural stability during cycling. Scanning electron microscopy analysis reveals that the Cr2O3@NC composite remains structurally intact throughout cycling. The innovative approach proposed in this study provides a new direction for the advancement of electrode materials for energy storage technologies.

Liquid metal-enhanced MoS2 nanocomposite for self-healing colloidal anodes in lithium-ion batteries

Energy storage is pivotal in addressing global energy challenges, with lithium-ion batteries (LIBs) at the forefront. However, their longevity is often limited by anode material degradation. Here, we introduce a novel LM/AgNWs@MoS2 nanocomposite anode material, synthesized via a one-step hydrothermal method, which integrates liquid metal's fluidity with silver nanowires' conductivity and MoS2's rapid lithium-ion diffusion. This composite demonstrates exceptional cycling stability, maintaining 468 mA h g−1 over 2000 cycles at 1 A g−1, and self-heals electrode cracks, offering a significant advancement for LIBs durability and safety. The LM/AgNWs@MoS2 nanocomposite addresses the critical need for durable, self-healing anode materials in LIBs, pushing forward the development of next-generation energy storage solutions.

Mechanically Robust Polyimide Binder Realizes Stable and High Electrochemical Performance for Micro-Silicon Anodes in Lithium-Ion Batteries.

Silicon anodes have been considered one of the most promising candidates for Li-ion batteries due to their high theoretical specific capacity. However, the practical use of silicon anodes is impeded due to side reactions and volumetric change (from 300~400%) charge/discharge process. Binders played a crucial role in Li-ion batteries by effectively mitigating the stress resulting from the volumetric expansion in silicon-based anodes. Herein, we developed a mechanically stable polyimide binder PI-CF3 that introduced trifluoromethyl and hydroxyl groups for commercial microparticular silicon anodes. With a highest Young's modulus of ~921.1 MPa, the binder presented the maximum resilience during the charging and discharging of Micro-Si, integrating the morphology, and reducing the degree to which the electrode disrupted ion and electric pathways. Moreover, -OH and -CF3 groups of the binder could potentially interact with oxide layer at the surface of silicon through hydron bonds, and thereby results in a cross-linking network to improve interface stability during cycling. The as-prepared PI-CF3 binder with excellent intrinsic mechanical and electro-rich groups stabilizes the electrode structure and facilitates fast Li+ transportation. Consequently, micro-Si anode delivered initial specific capacity of 1838 mAh g-1 (at 0.6 A g-1), and at high mass (Si loading = 0.78 mg cm-2) these was retained about 1219 mAh g-1 after 330 cycles (only -0.061% capacity reduction per cycle).

Waxberry-like TiO2 with Synergistic Surface Modification of Pyrolytic Carbon Coating and Carbon Nanotubes as an Anode for Li-Ion Battery.

Titanium dioxide (TiO2) as an anode material for lithium-ion batteries (LIBs) has the advantages of tiny volume expansion, high operating voltage, and outstanding safety performance. However, due to the low conductivity of TiO2 and the slow diffusion rate of lithium ions (Li+), it is limited in the application of LIBs. Therefore, waxberry-like TiO2 comodified by pyrolytic carbon coating and carbon nanotubes was prepared in this work. The waxberry-like TiO2 with nanorods on its surface shortens the diffusion distance of Li+. Carbon nanotubes and waxberry-like TiO2 are tightly combined through electrostatic assembly and form a cross-linked conductive network to provide more electron transmission paths. A thin layer of pyrolytic carbon wraps carbon nanotubes and waxberry-like TiO2, which enhance the conductivity of the composites and ensure the structural integrity of the materials throughout the cycling process. The experimental data revealed that the discharge-specific capacity of TiO2@CNT@C is 170.5 mAh g-1 after 3000 cycles at a large current density of 5 A g-1, and the discharge-specific capacity is still 143 mAh g-1 at the superhigh rate of 10 A g-1, which provides excellent rate performance and cyclic stability. The efficient dual-carbon modification strategy could potentially be extended to other materials.

Molten salt assisted synthesis of Si/C nanocomposite derived from palygorskite and sodium alginate for electrochemical lithium storage.

Silicon/carbon (Si/C) nanocomposites are considered as one of the most promising anode materials for lithium-ion batteries due to their high capacity and suitable lithiation potential. However, the complex and time-consuming preparation processes of silicon-based nanocomposites and the unexpected silicon carbide generated during high treatment make it difficult to achieve high-performance Si/C nanocomposites for practical applications. Herein, a silicon/carbon nanocomposite is successfully prepared through a facile and eco-friendly molten salt assisted precarbonization-reduction method using palygorskite (PAL) and sodium alginate as raw materials. Based on physical characterizations, it is demonstrated that the sodium alginate plays a key role in the successful preparation of Si/C nanocomposite, which not only boosts uniform embedding of PAL nanoparticles in the carbon matrix but also releases molten sodium salt to suppress the formation of unexpected SiC. When used as an alternative anode material for lithium-ion battery applications, the as-obtained Si/C composite delivers a high reversible specific capacity of 1362.7 mA h g-1 with an initial Coulombic efficiency of 70.3% at a current density of 200 mA g-1 and excellent long-term cycling stability. The findings here provide a facile and eco-friendly molten salt assisted precarbonization-reduction method for high-performance silicon/carbon anode materials.

Pomegranate-like cobalt Phosphides@P-Doped carbon Nanostructures with controlled phase as anode materials for Lithium-Ion batteries

Transition metal phosphides (TMPs) have recently emerged as prominent energy conversion and storage materials owing to their unique physicochemical property. Nevertheless, it’s still a difficult task to obtain phase-control of TMPs owing to multiple energetically favorable stoichiometries. Herein, a phase-controllable cobalt phosphide@C with the pomegranate core–shell structure are successfully realized by employing Co-glycerate as precursors and phytic acid (PA) as P sources, etching and coordination agents. With the presence of six phosphoryl groups and the strong coordination ability, PA allows the self-phosphating of Co atoms and the P-doped carbon shell, as well as the confinement of the obtained nanoparticles Additionally, as an organic acid, PA can etch the Co-glycerate precursors with the formation of hollow structures. With different etching time, metal-rich phosphides Co2P@C and monophosphides CoP@C are successfully achieved. When applied as anode materials, CoP@C demonstrates superior lithium storage performance by delivering a prominent reversible capacity up to 1187 mAh/g at 0.1 A/g and shows no capacity loss at 1 A/g after 500 cycles. This work presents a simple protocol to obtain TMPs with tunable metal/phosphorus ratios, phase selectivity and interface engineering, which could be applied in the field of energy storage and electrocatalysis.

N, P co-Doped Hard Carbon Anodes for High-Performance Lithium-Ion Batteries with Enhanced Capacity Retention and Cycle Stability.

Compared to the traditional graphite anode, heteroatom-doped polymer carbon materials have high capacity retention due to their high porosity and porous structure. Therefore, they have great potential for application in lithium-ion battery (LIB) anodes. In this work,an N, P co-doped precursor polymer material (MBPp), synthesized via a one-pot method using bisphenol-A (C-source), melamine (N-source), and 9,10-Dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (P-source). The resulting N, P-co-doped hard carbon materials (MBPs) were prepared at various pyrolysis temperatures, yielding microporous, mesoporous, and macroporous structures. MBP materials demonstrated excellent electrochemical performance as LIB anodes. Notably, MBP-900 achieved a reversible capacity of 262 mAh g-1 at 1000 mA g-1 (in 0.005-2.0 V voltage range) with a capacity retention rate of 97.2% after 1000 cycles. These findings highlight the significance of MBP materials, which possess numerous defects, large layer gaps, and excellent cycle stability, in advancing the development of polymer anode materials for LIBs.

A DFT Study of Band-Gap Tuning in 2D Black Phosphorus via Li+, Na+, Mg2+, and Ca2+ Ions.

Black phosphorus (BP) and its two-dimensional derivative (2D-BP) have garnered significant attention as promising anode materials for electrochemical energy storage devices, including next-generation fast-charging batteries. However, the interactions between BP and light metal ions, as well as how these interactions influence BP's electronic properties, remain poorly understood. Here, we employed density functional theory (DFT) to investigate the effects of monovalent (Li+ and Na+) and divalent (Mg2+ and Ca2+) ions on the valence electronic structure of 2D-BP. Molecular orbital analysis revealed that the adsorption of divalent cations can significantly reduce the band gap, suggesting an enhancement in charge transfer rates. In contrast, the adsorption of monovalent cations had minimal impact on the band gap, suggesting the preservation of 2D-BP's intrinsic electrical properties. Energetic and charge analyses indicated that the extent of charge transfer primarily governs the ability of ions to modulate 2D-BP's electronic structure, especially under high-pressure conditions where ions are in close proximity to the 2D-BP surface. Moreover, charge polarization calculations revealed that, compared with monovalent cations, divalent cations induced greater polarization, disrupting the symmetry of the pristine 2D-BP and further influencing its electronic characteristics. These findings provide a molecular-level understanding of how ion interactions influence 2D-BP's electronic properties during ion-intercalation processes, where ions are in close proximity to the 2D-BP surface. Moreover, the calculated diffusion barrier results revealed the potential of 2D-BP as an effective anode material for lithium-ion, sodium-ion, and magnesium-ion batteries, though its performance may be limited for calcium-ion batteries. By extending our understanding of interactions between ions and 2D-BP, this work contributes to the design of efficient and reliable energy storage technologies, particularly for the next-generation fast-charging batteries.

SiO2/C double-layer-coated SiO as a high-performance anode for lithium-ion batteries

Silicon monoxide (SiO) has a high theoretical capacity as an anode for lithium-ion batteries, but its poor conductivity and bulk effect can cause the capacity to plummet. The combination of SiO and other materials to form a core–shell mechanism on the surface of SiO can effectively alleviate these problems. In this work, a silicon dioxide (SiO2)/carbon (C) bilayer core–shell structure coated on SiO anode material was designed and synthesized to address the issues inherent in core–shell structures. When the temperature was 900 °C, SiO@SiO2@C exhibited an excellent reversible capacity of 2500.08 mAh·g−1 and a first coulombic efficiency of 75.92 %. After 100 charge/discharge cycles, it still retained 1298.25 mAh·g−1 of its capacity. Compared with those of pure SiO, its cycling stability and capacity retention are significantly improved, providing a new approach for anode materials in lithium-ion batteries.

Exploring the potential of MXene nanohybrids as high-performance anode materials for lithium-ion batteries

Lithium-ion batteries (LIBs) are an integral part of modern life, powering diverse applications from transportable devices to electric vehicles. Efficacy of LIBs depends on the performance of their components with anode material playing the pivotal role. Traditional graphite anodes have limitations in capacity and rate capability. This review comprehensively discusses utilization of MXene-based composites as anode materials in LIBs. MXene composites exhibit versatile lithium storage mechanisms, involving intercalation and/or conversion reactions. Pure MXenes offer advantages of high capacity and cycling stability having challenges due to limited conductivity and mechanical fragility, restricting their practical utility, thereby affecting their performance in solid-state polymer electrolytes (SPEs). MXene composites overcome unsystematic dispersal and accumulation issues of pure MXene. MXenes in composite form could increase LIBs performance by overcoming limitations of pure MXenes, enabling breakthroughs in energy storage. The review covers different MXene composites viz., MXene/graphene, MXene/silicon, MXene/tin, MXene/carbon, MXene/metal oxide, and MXene/conducting polymer providing a holistic overview. Their performance, cycling stability, and rate capability are discussed to cover challenges and future prospects.

Synergetic organic-inorganic electrochemistry active architecture of hollow Bi-based metal-organic framework microspheres assembled with terephthalic acid ligands

Bismuth (Bi) is a promising anode material for lithium-ion batteries due to its high capacity. However, challenges such as low conductivity and significant volume expansion during charge cycles restrict its practical application. Metal-organic frameworks (MOFs), known for their controllable structure, hybrid inorganic-organic nature, large surface area, and high porosity, offer a solution to fix up above challenges. This study designs three-dimensional porous hollow spherical nanostructured bismuth-based MOF (Bi-MOF) by coordinating Bi3+ with terephthalic acid. The material features a functional spherical shell and internal pore structure that maintain open ion transport channels, abundant electrochemical sites, and a large contact area between electrolyte and electrode. This design accelerates ion/electron transport within the cavity, mitigating volume expansion during charge-discharge cycles and ensuring structural stability. As an anode material, Bi-MOF exhibits great electrochemical performance: retaining discharge capacities of 617.6 mAh g−1 after 1000 cycles at 1 A g−1 and 579.1 mAh g−1 after 200 cycles at 0.1 A g−1. Coupled with LiFePO4 cathodes, the full-battery maintains 93.1 mAh g−1 after 110 cycles at 1C. This work provides a train of thought to develop high-performance anode materials for enhanced lithium storage in lithium-ion batteries (LIBs) and validated the lithium storage mechanism of Bi-MOF.

Preparation of Fe2O3 nanoparticles with ultrathin carbon covered as lithium storage anodes

This study focuses on the development of ultrathin carbon (UTC) treated with Fe2O3 nanoparticles as anode materials for lithium-ion batteries (LIBs). Here, a simple hydrothermal method has been adopted to prepare Fe2O3@C nanocomposite, followed by annealing. The obtained Fe2O3@C demonstrates Fe2O3 nanoparticles (NPs) with uniform carbon, which effectively mitigates volume expansion and enhances electrochemical performance. Encouraging, the first principal calculations ensure that carbon doping in Fe2O3 can notably reduce the band gap from 2.12 to 1.10 eV and enhance electronic conductivity.

A Novel Gelatin Binder with Helical Crosslinked Network for High-Performance Si Anodes in Lithium-Ion Batteries.

Silicon(Si) is a promising anode material for lithium-ion batteries, but its large volume expansion during cycling poses a challenge for the binder design. In this study, a novel gelatin binder is designed and prepared with a helical crosslinked network structure. This gelatin binder is prepared by enzymatic crosslinking and immersion in Hofmeister salt solution, which induces the formation of network and helical secondary structures. The helical crosslinked network structure can be analogous to a spring group system to effectively dissipate the stress and strain caused by the Si expansion. The gelatin binder is further partially carbonized by low-temperature pyrolysis, which improves its conductivity and stability. The Sianode with the optimized gelatin binder exhibits high initial coulombic efficiency, excellent rate performance, and long-term cycling stability. This study provides an innovative approach for the preparation of high-performance Si anodes, namely by controlling the molecular configuration of the binder to significantly improve the cycle stability, which can also be applied to other high-capacity anode materials that suffer from large volume changes during cycling.

Lithium-ion batteries pitch-based carbon anode materials: The role of molecular structures of pitches

To understand the effect of molecular configurations of coal tar pitch (CTP) on the reaction mechanism of carbonization and Li storage performance of subsequent carbonized products, four CTPs with different molecular structures are treated by liquid and solid phase carbonization and then tested the electrochemical performance of their carbonized products as anode materials for Lithium-ion batteries (LIBs). The results reveal that CTP-1 with hexagon rings, zigzag edges, and long alkyl side chains provides a large number of free radicals during pyrolysis, promoting the parallel arrangement of aromatic molecules. Special addition patterns (linear and nonlinear simultaneous) of aromatic molecular in CTP-3 generate a large number of edge carbons and surface defects in the carbonized products. The high viscosity and arm-chair edge reduce the reactivity of CTP-4 molecules, and the presence of loops and oxygenated aromatics in CTP-4 also reduces the orientation of carbon stacks and the flatness of the microstructure. The electrochemical performance of the final products shows a significant difference. Among them, CTP-1-M-1400 with a specific capacity of 349 mAh g−1 at 0.1 A g−1 displays an excellent cycling performance. Large amounts of Li-ions (about 39.2 %) are stored at the edge and surface of CTP-3-M-1400. While large number of Li-ions (about 23.5 %) are stored in the microspaces of CTP-4-M-1400. In addition, excessive structure defects and oxygen-containing groups in CTP-4-M-1400 lead to decreased capacity retention.

Synthesis of high-entropy perovskite metal fluoride anode materials for lithium-ion batteries via a one-pot solution method

Synthesis of high-entropy perovskite metal fluoride anode materials for lithium-ion batteries via a one-pot solution method

Fast kinetics for lithium storage rendered by Li3VO4 nanoparticles/porous N-doped carbon nanofibers

Li3VO4 (LVO) has been recognized as an alternative anode material for lithium-ion batteries (LIBs) because of its appropriate lithium storage potential and capacity merits. However, its practical application is seriously hindered by slow reaction kinetics stemming from poor electronic conductivity. Herein, Li3VO4/porous N-doped carbon nanofibers (LVO/PNC NFs) are firstly designed and fabricated via an electrospinning method, utilizing the thermal decomposition characteristics of polylactic acid (PLA). The porous N-doped carbon nanofibers provide efficient electrolyte diffusion paths and facilitate ion transport. In addition, LVO nanoparticles are uniformly dispersed along the nanofibers to effectively inhibit particle aggregation. The obtained LVO/PNC NFs are evaluated as anodes for LIBs and deliver high reversible capacity of 768 mAh g−1 after 300 cycles at 0.2 A g−1, along with excellent rate capability (average capacity of 355 mAh g−1 at 8 A g−1 after 6 periodic rate testing) and long cycling life (286 mAh g−1 after 2000 cycles at 4 A g−1). The special porous nanofiber represents an effective strategy for improving the electronic conductivity, inhibiting particle aggregation, and ensuring rapid ion/charge transport towards advanced energy storage technologies.

Performance of high-energy storage activated carbon derived from olive pomace biomass as an anode material for sustainable lithium-ion batteries

In this work, we investigate how activated carbon (AC) derived from olive pomace biomass can be used as an anode material in lithium-ion batteries. The biomass-derived activated carbon has the potential to be highly efficient, deliver high performance, sustainable, and cost-effective in LIBs-related production. The activated carbon is prepared by using H3PO4 as a chemical activation agent, and then calcining the obtained product at 500°C for different controlled atmospheres under (i) air (AC-Atm), (ii) vacuum (AC-Vac), and (iii) argon (AC-Arg). The different samples were systematically analyzed using scanning electron microscopy (SEM), High-resolution transmission electron microscopy (HRTEM), energy dispersive spectroscopy (EDS), X-ray fluorescence (XRF), X-ray diffraction (XRD), FT-IR and Raman spectroscopy, and thermogravimetric analysis (TGA) to assess their properties. The electrochemical properties of the carbonaceous materials were studied by galvanostatic cycling, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The results showed high specific capacity and stable cycling performance, with capacities of 288, 184, and 56 mAh g-1 at the current density of 25 mA g-1 after 70 cycles for AC-Arg, AC-Vac, and AC-Atm respectively. Furthermore, the CE efficiency was nearly 100% from the first cycles. This study opens up interesting prospects and offers promising opportunities for more efficient recovery of unused olive pomace waste, by integrating it into energy storage applications, particularly sustainable lithium-ion batteries.