Anode Angle Research Articles

REDUCTION OF POTENTIAL RADIOLOGICAL RISKS FOR PATIENTS UNDERGOING DIAGNOSTIC EXAMS THROUGH MODIFICATION OF THE X-RAY SPECTRUM

The diagnostic medical practice using X-rays significantly contributes to the collective dose worldwide, where the inherent risk in each examination is proportional to the absorbed dose, which is related to deterministic and stochastic effects of ionizing radiation. Therefore, due to the necessity of optimizing each radiological procedure, this study aimed to reduce the absorbed dose in patients undergoing X-ray examinations by evaluating each parameter that modifies the spectral distribution. The Birch and Marshall method was employed to reconstruct and modify the X-ray spectra based on tube voltage, filtration, tube current, anode angle, and energy fluence modulation. By modifying these parameters, it was possible to reduce the absorbed dose in the patient’s skin by up to 38%. The proposed methodology is feasible for implementation in clinical centers, given the availability of copper filters incorporated into X-ray equipment. Additionally, an alternative technique involving tantalum filters is presented, achieving a reduction in absorbed dose of up to 57%. Thus, with the developed methodology, it is demonstrated that it is possible to reduce radiation doses by modifying spectral distributions, reproducing medical images with a significant reduction in the absorbed dose to the patient, while ensuring quality and safety in X-ray diagnostic procedures.

Recess-free thin-barrier AlGaN/GaN Schottky barrier diodes with ultra-low leakage current: Experiment and simulation study

In GaN Schottky barrier diodes (SBD), there is a trade-off between the turn-on voltage and the leakage current. In this study, recess-free 4 nm-thin-barrier AlGaN/GaN SBDs with minimal leakage current as well as excellent turn-on voltage homogeneity are developed, which enable better electrical control to pinch off the 2DEG channel under the anode region and avoids trap introduced in the barrier etching process. In detail, the effect of reverse stress on the SBD performance is initially explored by using differential conductance, and then, the anode-to-cathode distances and temperatures dependence of SBDs output characteristics are systematically studied. The fabricated thin-barrier GaN SBDs show a turn-on voltage of ∼0.75 V and a low level leakage current of 9.66 × 10−10 (1.91 × 10−8) A/mm at 300 (423) K, which is among the lowest reported values at the comparable reverse bias voltage and temperature. Moreover, structure parameters of the thin-barrier AlGaN/GaN SBD are systematically modeled and optimized by the TCAD simulations, including anode metal work function, Al mole fraction, the anode-to-cathode distance, and slanted anode angle. The introduction of slanted anode is found to have significant effect on the improvement of reverse breakdown voltage and leakage current characteristics.

Estimating of radiation output of X-RAY tube using mathematical model: Case of high-frequency machines

PurposeDuring any radiological procedure, it is important to know the dose to be-administered to the patient and this can be done by estimating the output of the X-ray tube either with a dosimeter or with a mathematical equation or Monte Carlo simulations. The aim of this work is to develop a new mathematical model equation (NMME) for estimating the output of high-frequency X-ray tubes. MethodsTo achieve this, data collected from ten machines in many regions of Cameroon were used (for nine machines) to build an initial model that does not take into account the anode angle and the tenth machine was used to test the model. Using the SpekCalc software, some simulations were carried out to evaluate the influence of the anode angle. This allowed the NMME to be proposed. ResultsThe deviations frequencies between 0.65% and 19.61% were obtained by comparing the output values obtained using initial model with the measured values. The statistical hypothesis test showed that the estimated values using initial model and NMME are in agreement with those measured unlike the Kothan and Tungjai model. For the tenth machine, the percentage difference between estimated and measured values is less than 8 %. ConclusionThese results show that the proposed model performed better than the previous models. In the absence of a dosimeter, the NMME could be used to estimate the output of high frequency X-ray machines and therefore the radiation doses received by patients during diagnostic X-ray examinations.

On the robustness of detective quantum efficiency within the limits of IEC 61267 RQA standard radiation qualities.

IEC 61267 allows a certain leeway regarding the establishment of radiation qualities in order to enable the use of X-ray tubes having different anode angles and inherent filtrations. This allowance has a direct impact on the calculation of the detective quantum efficiency and may potentially complicate any comparison of different imaging detectors based on this quantity. This work investigates this effect by applying computational methods. To this end, an algorithm was implemented to calculate the variation of the squared signal-to-noise ratio per air kerma for RQA standard radiation qualities and to deduce corresponding uncertainties based on GUM Supplement 2. For RQA standard radiation qualities, the results show standard uncertainties for the squared signal-to-noise ratio per air kerma of between 0.05 and 2.1%. Comparing imaging detectors based on detective quantum efficiency is associated with substantial uncertainty for some radiation qualities. This is due to the different photon fluences with respect to energy that are allowed by IEC 61267 for identical standard radiation qualities.

Technical note: SpekPy Web-online x-ray spectrum calculations using an interface to the SpekPy toolkit.

Knowledge of the photon spectrum emitted from an x-ray tube is frequently needed in imaging and dosimetry contexts. As the spectrum characteristics are influenced by several parameters and routine measurement of a spectrum is often impractical, a variety of software programs have been developed over the decades for convenient calculations. SpekPy is a state-of-the-art software package containing several spectrum models, and was created to estimate photon spectra originating from x-ray tubes using a small set of input parameters (e.g., anode material, anode angle, tube potential, filtration, etc.). SpekPy is distributed as a Python toolkit and is available free of charge. The toolkit does, however, lack a graphical user interface and a user is required to write a Python script to make use of it. In this work this limitation is addressed by introducing a web application called SpekPy Web: a graphical user interface together with an application programmable interface (API). These developments both make the SpekPy spectrum models accessible to a broader set of users and increases the ease of use for existing users. SpekPy Web is hosted at: https://spekpy.smile.ki.se. The functionality of the software is demonstrated, using its API, by estimating first half-value layers (HVLs) for 15 standard beam qualities from the International Bureau of Weights and Measures (BIPM). The estimated HVLs were found to all be within 3.5% agreement when compared to experimental values, with an average calculation time of 2.5 s per spectrum. half-value-layer, software, x-ray spectrum.

Simulation study of a novel small animal FLASH irradiator (SAFI) with integrated inverse-geometry CT based on circularly distributed kV X-ray sources

Ultra-high dose rate (UHDR) radiotherapy (RT) or FLASH-RT can potentially reduce normal tissue toxicity. A small animal irradiator that can deliver FLASH-RT treatments similar to clinical RT treatments is needed for pre-clinical studies of FLASH-RT. We designed and simulated a novel small animal FLASH irradiator (SAFI) based on distributed x-ray source technology. The SAFI system comprises a distributed x-ray source with 51 focal spots equally distributed on a 20 cm diameter ring, which are used for both FLASH-RT and onboard micro-CT imaging. Monte Carlo simulation was performed to estimate the dosimetric characteristics of the SAFI treatment beams. The maximum dose rate, which is limited by the power density of the tungsten target, was estimated based on finite-element analysis (FEA). The maximum DC electron beam current density is 2.6 mA/mm2, limited by the tungsten target's linear focal spot power density. At 160 kVp, 51 focal spots, each with a dimension of 2times 20 mm2 and 10° anode angle, can produce up to 120 Gy/s maximum DC irradiation at the center of a cylindrical water phantom. We further demonstrate forward and inverse FLASH-RT planning, as well as inverse-geometry micro-CT with circular source array imaging via numerical simulations.

G4XRTube: A Geant4-based Monte Carlo application for X-ray tube simulation

This paper focuses mainly on the generation of X-rays in the X-ray tubes and their utilization in imaging applications. In this work, the Geant4 Monte Carlo simulation toolkit was used to develop an application for simulating the production of X-rays in X-ray tubes. This Geant4-based Monte Carlo application generates X-ray spectra depending on anode angle, tube voltage, filter and anode material. In addition to X-ray spectra, G4XRTube can be used, for instance, for the prediction of half-value layer (HVL) and investigation of anode heel effect. The utilization of G4XRTube can also be extended to include other fields such as radiation protection, shielding, dosimetry and investigation of the performance of X-ray tubes and detectors. The results obtained in this work with G4XRTube were validated against existing data in the literature. Specifically, we compared our results with experimental literature data and TASMICS, SpekCalc, and SpekPy codes. The comparison shows a good agreement between G4XRTube results and other data.

Comparison of Non-Uniform Image Quality Caused by Anode Heel Effect between Two Digital Radiographic Systems Using a Circular Step-Wedge Phantom and Mutual Information.

The purpose of this study was to compare non-uniform image quality caused by the anode heel effect between two radiographic systems using a circular step-wedge (CSW) phantom and the normalized mutual information (nMI) metric. Ten repeated radiographic images of the CSW and contrast-detail resolution (CDR) phantoms were acquired from two digital radiographic systems with 16- and 12-degree anode angles, respectively, using various kVp and mAs. To compare non-uniform image quality, the CDR phantom was physically rotated at different orientations, and the directional nMI metrics were calculated from the CSW images. The directional visible ratio (VR) metrics were calculated from the CDR images. Analysis of variance (ANOVA) was performed to understand whether the nMI metric significantly changed with kVp, mAs, and orientations with Bonferroni correction. Mann-Whitney's U test was performed to compare the metrics between the two systems. Contrary to the VR metrics, the nMI metrics significantly changed with orientations in both radiographic systems. In addition, the system with the 12-degree anode angle exhibited less uniform image quality compared to the system with the 16-degree anode angle. A CSW phantom using the directional nMI metric can be significantly helpful to compare non-uniform image quality between two digital radiographic systems.

Sophisticated 3D microstructural reconstruction for numerical analysis of electrolyte imbibition in Li-ion battery separator and anode

A simplified approach to visualize and create high-fidelity three-dimensional (3D) microstructure reconstruction of Li-ion battery (LIB) separator (Polyethylene - PE) is proposed here, for comprehending the relationship between transport properties (Electrolyte saturation, Residual gas phase, effective transport coefficient - δ, and Macmullin number - Nm) and microstructure characteristics. In the construction of Li-ion battery, since electrolyte filling in separator and electrode is a decisive step that primarily governs the storage capacity, battery life cycle and safety, herein the study was extended to identify the quantity of residual gas in the separator/electrode microstructure for facilitating better wetting and infilling of electrolyte into the electrode and separator. Moreover, the effect of structural and transport properties with different graphite content (50%, 60%, and 70%) in the electrode were investigated followed by contact angle (CA) effect with electrolyte in the separator and graphite is presented. From the results of the study, it is claimed that the graphite contents of anode and contact angle of electrolytes explicitly impact the transport properties, in addition the conductivity of the electrolyte diminishes with respect to the microstructure of separator and anode.

Simulating Medical Imaging X-Ray Tubes with Various Parameters Using BEAMnrc Monte Carlo Software

Context: Medical imaging has a wide range of applications in today’s society. Basic projectional radiography, CT scans, mammograms and a range of other advanced technologies all use x-rays to create a large number of examinations every day across the world. The most essential component of such medical equipment is the x-ray tube, which creates and produces x-rays. Objective: We describe and investigate an abstract model-geometry of a simple x-ray tube utilizing the open-source software package of BEAMnrc of the EGSnrcmp family, which is well validated by several studies over the years, for high and low energy photons generation. Methodology: Our research focuses on two different electron beam energies: 120 keV and 30 keV. The 120 keV is the typical energy for simple projectional radiographic exams and CT examinations, whereas the 30 keV is the typical energy of mammography. Results: Two different anode materials are used for each case, Gold (Au) and Tungsten (W) for 120 keV because these are the most common in projectional radiography and CT; Molybdenum (Mo) and Rhodium (Rh) for 30 keV because with these targets most mammography exams are carried out. The aim of this work is to show how the BEAMnrc software package can simulate effectively x-ray generation of low-energy photons which are utilized in modern medical imaging procedures. We describe useful information on anode-target characteristics, such as anode angle, anode material, and metal filter materials, based on previous quality studies even by using software other than BEAMnrc. Conclusion: We demonstrate that BEAMnrc can be efficiently used for Monte Carlo modeling of low-energy photons.

Dose-Area Product-to-Effective Dose Conversion Coefficients for Pelvic Radiography Using a Monte Carlo Program.

OBJECTIVE. The purpose of this study was to determine dose-area product-to-effective dose (DAP/E) conversion coefficients for a five-view pelvic radiograph series. DAP/E conversion coefficients may be used for radiation dose optimization when designing institutional protocols for pelvic trauma evaluation. MATERIALS AND METHODS. We conducted a retrospective record review of 25 patients at a level 1 trauma center who had sustained pelvic fractures and required a five-view pelvic radiograph series during workup. E values given in International Commission on Radiological Protection Publication 103 were simulated with a PC-based Monte Carlo program in conjunction with anthropomorphic phantoms adjusted on the basis of patient height and weight. Inputs included tube voltage (in kV), tube filtration (in millimeters of aluminum), anode angle, x-ray beam collimation, geometric distances, and angle of projection for each radiograph in the series. An incident polychromatic x-ray spectrum was generated and matched to the corresponding DAP values of each radiograph, and regression analysis was performed for the DAP/E conversion coefficients. RESULTS.E was strongly correlated with DAP independent from body mass index, with a mean global DAP/E conversion coefficient of 0.0125 mSv/dGy · cm2 for all radiographs (R2 = 0.95). Mean DAP/E conversion coefficients were 0.0133, 0.0110, 0.0143, 0.0113, and 0.0101 mSv/dGy · cm2 for anteroposterior, inlet, outlet, Judet left, and Judet right views, respectively (all R2 ≥ 0.94). CONCLUSION. DAP/E conversion coefficients are provided for a five-view pelvic radiograph series to allow reliable estimation of E. Measurement of cumulative E may affirm protocol design changes for the management of pelvic trauma.

Structural Shielding Evaluation: A Case Study of the Radiography Room of a Rural Hospital in Jos, Nigeria

IntroductionMost Nigerian rural hospitals constructed before the publication of the 2005 National Council on Radiation Protection and Measurements Report No. 147 did not undergo a performance assessment at the time of construction. To avoid overexposure to ionizing radiation and to ensure adequate protection of patients, workers, and the public, the shielding barriers need to be evaluated to ascertain that they conform to this standard. MethodsThis study evaluates the shielding barriers for the general radiography room in a rural hospital in Jos, Nigeria. The workload information, generator voltage waveform, anode material, filtration, and anode angle with XRAYBARR calculation model were used to estimate the thickness of lead, concrete, gypsum, steel, plate glass, and wood required to shield the X-ray facility installed in the hospital. The design dose limit was compared to the estimated shielded dose, and the calculated shielded barrier thickness to the design shielded barrier thickness was also compared. ResultsThe unshielded radiation doses inside the X-ray room were high, indicating that the radiological department of the study area is not minimizing radiation doses to patients. The calculated doses beyond the barriers were greater than the design dose limit, indicating that the shielded barriers in place were not adequate and did not comply with the international standard. DiscussionHospitals must understand the type of shielding materials that can provide adequate protection and to what extent they can protect their radiography rooms. Management and radiation protection agencies need to ascertain whether these barriers are still adequate or require reinforcement through regular quality assurance testing. Due to an increase in workload associated with an increase in population and urbanization, proper policies are needed more than ever in this and other rural hospitals in Nigeria. ConclusionThe tested X-ray rooms did not comply with international recommendations for shielding thickness. Except for the door, console, and changing room, a 0.5 mm-thick lead reinforcement is required. It is also recommended that quality assurance testing occur on an annual basis.

Calculation of air kerma inside the radiation field of X-ray tube

The air kinetic energy released per unit of mass (air kerma) quantity is of importance in both medicine and industry for evaluating the radiation field of X-ray tubes and also for calibrating the reference instruments. The air kerma spatial distribution inside the X-ray tube's radiation field is not uniform because of the heel effect phenomenon. In this paper, a combination of Monte Carlo N Particle eXtended (MCNPX) simulation code and artificial neural network (ANN) has been utilized to estimate the air kerma inside the radiation field of X-ray tube for a wide range of tube voltages (50–600 kV) which covers both medical and industrial applications. At first, an X-ray tube with an anode angle of 20° was simulated using MCNPX code. Next, in order to provide the required data for training the network, 1375 point detectors were placed in different positions inside the conical radiation field of the simulated X-ray tube and then the air kerma was calculated for tube voltages in the range of 50–600 kV with a step of 50 kV. The tube voltage and point detector's spherical coordinates including distance from target, tangential angle and polar angle were utilized as the 4 inputs and the air kerma was used as the output of the ANN. After training the ANN, the proposed ANN model could estimate the air kerma in every position inside the radiation field of X-ray tube for a wide range of voltages (50–600 kV) with a mean relative error (MRE) of less than 0.67%.

Comparison between Predicted and Measured X-Ray Output in Some Conventional Radiography Units

This study aims to investigate how accurate are TASMICS and TASMIP models in predicting the X-ray output of some Conventional Radiology X-ray units with high frequency generators. The X-ray output in microgray per milliampere seconds (μGy/mAs) at 100 cm from the X-ray tube was determined for selected high voltages and taking into account the total filtration. The X-ray output was then measured directly with the multi-purpose detectors (MPD), Raysafe X2. The maximum relative error between measured and predicted values was found to be equal to 20%. The maximum relative error between measured and predicted values obtained demonstrates the difficulty of accurately predicting the X-ray tube output using TASMICS and TASMIP models since they are based on fixed anode angles and different composition of the tungsten anode.

Unfolding X-ray spectra using a flat panel detector. Determination of the accuracy of the method with the Monte Carlo method

The primary X-ray spectrum depends on different parameters such as high voltage, filament current, high voltage ripple, anode angle and thickness of filter material. The objective of this work is to determine whether the unfolding technique based on the Tikhonov regularization method is accurate enough to estimate the X-ray spectrum when slight changes in the operation variables are considered. In this frame, several X-ray spectra are considered (extracted from the IPEM78 Catalogue Report) varying the main operation variables of the X-ray tube (high voltage, voltage ripple, filter thickness and filter material). With those spectra, the corresponding absorbed dose curves are obtained by simulation with a MCNP5 model reproducing a flat panel detector and a PMMA wedge. Once the absorbed dose curves are simulated and applying the unfolding Tikhonov regularization method, the unfolded spectrum is obtained, which is finally compared with the theoretical one (IPEM78 Catalogue Report). Discrepancies between unfolded and primary X-ray spectra can be attributed to the fact that this is an ill-posed problem, and the unfolding of the spectrum is strongly affected by the method used to improve the conditioning of the response function (response matrix).

PATIENT RADIATION DOSE FROM CHEST X-RAY EXAMINATIONS IN THE WEST BANK—PALESTINE

Radiation doses to patients resulting from chest X-ray examinations were evaluated in four medical centers in the West Bank and East Jerusalem-Palestine. Absorbed organ and effective doses were calculated for a total of 428 adult male and female patients by using commercially available Monte Carlo based softwares; CALDOSE-X5 and PCXMC-2.0, and hermaphrodite mathematical adult phantoms. Patients were selected randomly from medical records in the time period from November 2014 to February 2015. A database of surveyed patients and exposure factors has been established and includes: patient's height, weight, age, gender, X-ray tube voltage, electric current (mAs), examination projection (anterior posterior (AP), posterior anterior (PA), lateral), X-ray tube filtration thickness in each X-ray equipment, anode angle, focus to skin distance and X-ray beam size. The average absorbed doses in the whole body from different projections were: 0.06, 0.07 and 0.11 mGy from AP, PA and lateral projections, respectively. The average effective dose for all surveyed patients was 0.14 mSv for all chest X-ray examinations and projections in the four investigated medical centers. The effect of projection geometry was also investigated. The average effective doses for AP, PA and lateral projections were 0.14, 0.07 and 0.22 mSv, respectively. The collective effective dose estimated for the exposed population was ~60 man-mSv.

Generation and analysis of clinically relevant breast imaging x-ray spectra.

The purpose of this work was to develop and make available x-ray spectra for some of the most widely used digital mammography (DM), breast tomosynthesis (BT), and breast CT (bCT) systems in North America. The Monte Carlo code MCNP6 was used to simulate minimally filtered (only beryllium) x-ray spectra at 8 tube potentials from 20 to 49 kV for DM/BT, and 9 tube potentials from 35 to 70 kV for bCT. Vendor-specific anode compositions, effective anode angles, focal spot sizes, source-to-detector distances, and beryllium filtration were simulated. For each 0.5keV energy bin in all simulated spectra, the fluence was interpolated using cubic splines across the range of simulated tube potentials to produce spectra in 1 kV increments from 20 to 49 kV for DM/BT and from 35 to 70 kV for bCT. The HVL of simulated spectra with conventional filtration (at 35 kV for DM/BT and 49 kV for bCT) was used to assess spectral differences resulting from variations in: (a) focal spot size (0.1 and 0.3mm IEC), (b) solid angle at the detector (i.e., small and large FOV size), and (c) geometrical specifications for vendors that employ the same anode composition. Averaged across all DM/BT vendors, variations in focal spot and FOV size resulted in HVL differences of 2.2% and 0.9%, respectively. Comparing anode compositions separately, the HVL differences for Mo (GE, Siemens) and W (Hologic, Philips, and Siemens) spectra were 0.3% and 0.6%, respectively. Both the commercial Koning and prototype "Doheny" (UC Davis) bCT systems utilize W anodes with a 0.3mm focal spot. Averaged across both bCT systems, variations in FOV size resulted in a 2.2% difference in HVL. In addition, the Koning spectrum was slightly harder than Doheny with a 4.2% difference in HVL. Therefore to reduce redundancy, a generic DM/BT system and a generic bCT system were used to generate the new spectra reported herein. The spectral models for application to DM/BT were dubbed the Molybdenum, Rhodium, and Tungsten Anode Spectral Models using Interpolating Cubic Splines (MASMICSM-T , RASMICSM-T , and TASMICSM-T ; subscript "M-T" indicating mammography and tomosynthesis). When compared against reference models (MASMIPM , RASMIPM , and TASMIPM ; subscript "M" indicating mammography), the new spectral models were in close agreement with mean differences of 1.3%, -1.3%, and -3.3%, respectively, across tube potential comparisons of 20, 30, and 40 kV with conventional filtration. TASMICSbCT -generated bCT spectra were also in close agreement with the reference TASMIP model with a mean difference of -0.8%, across tube potential comparisons of 35, 49, and 70 kV with 1.5mm Al filtration. The Mo, Rh, and W anode spectra for application in DM and BT (MASMICSM-T , RASMICSM-T , and TASMICSM-T ) and the W anode spectra for bCT (TASMICSbCT ) as described in this study should be useful for individuals interested in modeling the performance of modern breast x-ray imaging systems including dual-energy mammography which extends to 49 kV. These new spectra are tabulated in spreadsheet form and are made available to any interested party.

Focal spot size reduction using asymmetric collimation to enable reduced anode angles with a conventional angiographic x-ray tube for use with high resolution detectors.

The high-resolution requirements for neuro-endovascular image-guided interventions (EIGIs) necessitate the use of a small focal-spot size; however, the maximum tube output limits for such small focal-spot sizes may not enable sufficient x-ray fluence after attenuation through the human head to support the desired image quality. This may necessitate the use of a larger focal spot, thus contributing to the overall reduction in resolution. A method for creating a higher-output small effective focal spot based on the line-focus principle has been demonstrated and characterized. By tilting the C-arm gantry, the anode-side of the x-ray field-of-view is accessible using a detector placed off-axis. This tilted central axis diminishes the resultant focal spot size in the anode-cathode direction by the tangent of the effective anode angle, allowing a medium focal spot to be used in place of a small focal spot with minimal losses in resolution but with increased tube output. Images were acquired of two different objects at the central axis, and with the C-arm tilted away from the central axis at 1° increments from 0°-7°. With standard collimation settings, only 6° was accessible, but using asymmetric extended collimation a maximum of 7° was accessed for enhanced comparisons. All objects were positioned perpendicular to the anode-cathode direction and images were compared qualitatively. The increasing advantage of the off-axis focal spots was quantitatively evidenced at each subsequent angle using the Generalized Measured-Relative Object Detectability metric (GM-ROD). This anode-tilt method is a simple and robust way of increasing tube output for a small field-of-view detector without diminishing the overall apparent resolution for neuro-EIGIs.

Study on the characteristics of X-ray spectra in imaging diagnosis using Monte Carlo simulations

X-rays are widely used in diagnostic imaging such as radiography and computed tomography. An understanding of the X-ray spectrum is essential for estimating the dose absorbed by the patient and for improving image quality. In this research, X-ray emission spectra were investigated by using two different approaches: a Monte Carlo method using the MCNP5 code and a semi-empirical calculation with SpekCalc software. The results were compared with each other to validate the Monte Carlo simulation of the X-ray spectra, so that the simulation model can be applied to estimating the dose rate distribution in X-ray imaging. The obtained results show good agreement between the two approaches, but some divergence is still observed in the characteristic X-ray peaks. In addition, the influence of X-ray tube parameters such as the peak voltage, filter, anode angle and target material on of the beam quality was investigated.

디지털 엑스선유방촬영장치에서 검출기 위치에 따른 공간분해능의 변화

ABSTRACT X-ray mammography is the most effective method for the diagnosis of calcified lesions of various breast diseases. To reduce patient dose and to obtain optimal image required for diagnosis, the performance of the mammography system should be maintained continuously. Because the target (anode) angle of the X-ray tube is measured from the central X-ray, the effective angle can be slightly different in view of the position on the detector, which can result in degrading spatial resolution of the imaging within the field of view. In this study, we measured the MTF to examine spatial resolution for positions on the detector in the digital mammography system. For a tungsten wire of 50 ㎛ diameter, the highest spatial frequency was obtained. It meant that a wire diameter for measuring MTF through LSF should be small compared to the pixel size of the detector used in the mammography system. The spatial resolution showed slightly different performance according to positions on the detector. The center position gave the best spatial resolution and positions away from the center showed the degraded performance although the difference of the spatial resolution was small. The effective focal spot size of the full width at half maximum also showed similar result. It concluded that the slightly increase of the effective focal spot size gave the degradation of the spatial resolution for positions on the detector.