Analysis Of Solution Samples Research Articles

Liquid chromatography coupled to Venturi easy ambient sonic spray ionization mass spectrometry

Venturi easy ambient sonic spray ionization (V-EASI) is a soft ambient ionization (AI) source that has the advantages of being suitable to the analysis of samples in solution (differently from the majority of AI sources), performing self-pumping, voltage- and heat-free ionization, and requiring minimum or no sample preparation. Since this ionization technique has not been fully explored, the present study provides a proof of principle of the coupling of liquid chromatography to mass spectrometry (LC-MS) using V-EASI as the interface. In order to test the performance of the developed LC-V-EASI-MS system, a quantification method for bixin, a natural dye from annatto (Bixa Orellana L.), which is known to be sensitive to the high voltage applied for electrospray ionization mass spectrometry (ESI-MS) analysis, was validated according to FDA criteria and tested in real samples. The analytical method was successfully applied and met the validation criteria, providing a detectability 10 times better than methods already reported to the quantification of bixin and no matrix effect was observed. Therefore, this proof of principle contributes to the continuous development of AI sources that represents the last great technological advance in MS towards becoming a miniaturized technique able to analyze samples closer to their actual state.

239, 240, 241Pu fingerprinting of plutonium in western US soils using ICPMS: solution and laser ablation measurements

Sector field inductively coupled plasma mass spectrometry (SF-ICPMS) has been used with analysis of solution samples and laser ablation (LA) of electrodeposited alpha sources to characterize plutonium activities and atom ratios prevalent in the western USA. A large set of surface soils and attic dusts were previously collected from many locations in the states of Nevada, Utah, Arizona, and Colorado; specific samples were analyzed herein to characterize the relative contributions of stratospheric fallout vs. Nevada Test Site (NTS) plutonium. This study illustrates two different ICPMS-based analytical strategies that are successful in fingerprinting Pu in environmental soils and dusts. Two specific datasets have been generated: (1) soils are leached with HNO3-HCl, converted into electrodeposited alpha sources, counted by alpha spectrometry, then re-analyzed using laser ablation SF-ICPMS; (2) samples are completely dissolved by treatment with HNO3-HF-H3BO3, Pu fractions are prepared by extraction chromatography, and analyzed by SF-ICPMS. Optimal laser ablation and ICPMS conditions were determined for the re-analysis of archived alpha spectrometry "planchette" sources. The best ablation results were obtained using a large spot size (200 microm), a defocused beam, full repetition rate (20 Hz) and scan rate (200 microm s(-1)); LA-ICPMS data were collected with a rapid electrostatic sector scanning experiment. Less than 10% of the electroplated surface area is consumed in the LA-ICPMS analysis, which would allow for multiple re-analyses. Excellent agreement was found between (239+240)Pu activities determined by LA-ICPMS vs. activity results obtained by alpha spectrometry for the same samples ten years earlier. LA-ICPMS atom ratios for 240Pu/239Pu and 241Pu/239Pu range from 0.038-0.132 and 0.00034-0.00168, respectively, and plot along a two-component mixing line (241Pu/239Pu = 0.013 [240Pu/239Pu] - 0.0001; r2 = 0.971) with NTS and global fallout end-members. A rapid total dissolution procedure, followed by extraction chromatography and SF-ICPMS solution Pu analysis, generates excellent agreement with certified (239+240)Pu activities for standard reference materials NIST 4350b, NIST 4353, NIST 4357, and IAEA 385. (239+240)Pu activities and atom ratios determined by total dissolution reveal isotopic information in agreement with the LA-ICPMS dataset regarding the ubiquitous mixing of NTS and stratospheric fallout Pu sources in the regional environment. For several specific samples, the total dissolution method reveals that Pu is incompletely recovered by simpler HNO3-HCl leaching procedures, since some of the Pu originating from the NTS is contained in refractory siliceous particles.

New mechanistic aspects of methanol oxidation

Parallel reactions during methanol electro-oxidation at smooth Pt electrodes lead to the formation of considerable amounts of HCHO and HCOOH together with CO 2. In the present paper, the yields of different products at 0.6 V have been measured, using smooth polycrystalline and Pt(1 1 1) electrodes. Analysis of solution samples after ca. 15 min of electrolysis was performed via HPLC. The well-known effect of the base electrolyte on the rate of methanol oxidation is observed: lower currents are obtained in 0.5 M H 2SO 4 than in 0.1 M HClO 4 solutions. The reason for this effect is rationalized by comparing the distribution of products in both electrolytes. This indicates that strong adsorption of sulfate hinders methanol oxidation by inhibiting the dissociative steps where the adsorbed CO intermediate is formed. The reactions forming the other soluble products, HCHO and HCOOH are not affected by the presence of H 2SO 4. It is suggested that the latter processes occur by an Eley–Rideal mechanism, while the reaction forming CO 2 follows a Langmuir–Hinshelwood mechanism.

Application of ion chromatography in steel industry

Most steel plant laboratories in the Benelux‐countries are equipped with ICP‐AES and AA‐spectrometers dedicated to the analysis of samples in solution, mainly for the quantitative determinations of cations. These methods, however, are hardly suitable for the analysis of anions; hence, the interest in applying the ion chromatography method for the determination of these ions. The “Centre de Recherches Métallurgiques” studied different applications of ion chromatography (I.C.) in steel industry laboratories. In this paper, four major applications of this technique are described: analysis of waste waters, determination of the anions in surface treatment baths, analysis of rolling mill coolants, and analysis of sulphur in steel.

X-ray fluorescence analysis using synchrotron radiation at the photon factory

X-ray fluorescence experiments at the Photon Factory in Japan are described. An energy-dispersive X-ray fluorescence system was combined with various excitation modes, i.e., a continuum and a monochromatic excitation, which consist of a crystal monochromator or a wide band pass monochromator. These excitation modes provide a wide range of band width and photon flux of excitation beams. Minimum detection limits obtained for a thin sample were less than 0.1 ppm and 0.1 pg when there was no line interference. Advantages of using monochromatic excitation are discussed, with emphasis on the possibility of chemical state analysis. Grazing incidence X-ray fluorescence is a technique very appropriate to synchrotron radiation characteristics. Near-surface analysis and trace analysis of solution samples placed on a total reflection support were made. Future plans are discussed, including microbeam analysis, tomography, X-ray excited optical fluorescence, and applications of insertion devices (undulator and wiggler).

Analysis of solution samples by microwave-induced plasma excitation

Analysis of solution samples by microwave-induced plasma excitation