Ambient RF Energy Harvesting Research Articles

Modeling and Analyzing of CMOS Cross-Coupled Differential-Drive Rectifier for Ultra-Low-Power Ambient RF Energy Harvesting

This paper models and analyzes the Complementary Metal Oxide Semiconductor (CMOS) cross-coupled differential-drive (CCDD) rectifier for Ultra-Low-Power ambient radio-frequency energy harvesters (RFEHs) working in the subthreshold region. In this paper, two closed-form equations of CCDD rectifier output voltage and input resistance in the subthreshold region were derived based on BSIM4 models of NMOS and PMOS. The model give insight to specify circuit parameters according to different inputs, transistor sizes, threshold voltages, numbers of stages, load conditions and compensation voltages, which can be used to optimize the rectifier circuit. There is a good agreement between the simulation results and these models, and these models have a maximum deviation of 10% in comparison with the simulation results in the subthreshold region. The measurement results of a single-stage CCDD rectifier reported in a previous paper were adopted to verify the model. The output voltage and input resistance predicted by these models provide excellent consistency with corresponding measurement results. The model can be employed to optimize the CCDD rectifier without expensive calculation in the design stage.

Analysis and Design of a 970-MHz, 108-Stage CMOS Ambient RF Energy Harvester With −36.5-dBm Input Power Sensitivity

Analysis and Design of a 970-MHz, 108-Stage CMOS Ambient RF Energy Harvester With −36.5-dBm Input Power Sensitivity

Ambient RF Energy Harvesting

In this paper, we present a study of ambient RF energy harvesting techniques. The measurement of the ambient RF power density is presented. The average of the density in broadband (1GHz- 3.5GHz) is in the order of -12dBm/m² (63µW/m²). Two systems have been studied to recover the RF energy. The first is a broadband system without matching circuit. The second is a narrow band system (1.8-1.9GHz) with a matching circuit. The rectifier circuit RF / DC and the choice of the load to optimize the DC power recovered are presented. The preliminary results indicate that the recovered energy is not sufficient to directly power devices but could be stored in a super-capacity or micro-batteries.

Machine-Learning-Based Predictive Modeling Analysis in Ambient RF Energy Harvesting for IoT Systems

Machine-Learning-Based Predictive Modeling Analysis in Ambient RF Energy Harvesting for IoT Systems

Battery-Free Hybrid Ambient RF and Wind Energy Harvester for Outdoor IoTs

Battery-Free Hybrid Ambient RF and Wind Energy Harvester for Outdoor IoTs

Omnidirectional Flexible Tri-Band Rectenna With Eliminated Matching Circuit for Ambient RF Energy Harvesting

Omnidirectional Flexible Tri-Band Rectenna With Eliminated Matching Circuit for Ambient RF Energy Harvesting

A Fully Integrated CMOS Tri-Band Ambient RF Energy Harvesting System for IoT Devices

A Fully Integrated CMOS Tri-Band Ambient RF Energy Harvesting System for IoT Devices

Miniaturized Broadband Bi-Yagi Antenna Array for Ambient RF Energy Harvesting.

This paper presents a miniaturized broadband Bi-Yagi antenna array that covers a bandwidth from 1.79 GHz to 2.56 GHz. The proposed antenna achieves a tradeoff between maximizing bandwidth, effective area, and gain while minimizing physical dimensions. The antenna design considers the coupling between the radiator and director elements, resulting in increased bandwidth as the resonating modes shift apart. Additionally, the proposed design optimizes element spacing and dimensions to achieve high gain, wide bandwidth, efficient radiation, and a minimum aperture size. The proposed antenna, with physical dimensions of 138.6 mm × 47.7 mm × 1.57 mm, demonstrates gains ranging from 6.2 dBi to 9.34 dBi across the frequency range, with a total efficiency between 88% and 98%. The proposed design is experimentally validated by measuring the reflection coefficients, input impedance, gain, and normalized radiation pattern. These features make the antenna well suited for capturing and harvesting electromagnetic waves in mobile wireless and Wi-Fi applications.

A High-PCE Range-Extension CMOS Rectifier Employing Advanced Topology Amalgamation Technique for Ambient RF Energy Harvesting

This paper presents a cross-coupled CMOS rectifier for ambient RF energy harvesting, which utilizes an advanced topology amalgamation technique to significantly improve the rectifier’s power conversion efficiency (PCE) and power dynamic range (PDR), also known as the high-PCE range. Our novel technique involves adaptively self-biasing the rectifying PMOS in the last stage of the proposed rectifier, which deactivates the cross-coupled counterpart and enables the subsequent diode-based rectifier circuitry to operate efficiently during high-power operation and extends the high-PCE range by mitigating the leakage current. Fabricated in a 65-nm CMOS process, our proposed rectifier scores a wide PDR of 21 dB at 900 MHz and 15 dB at 1.8 GHz with a peak PCE of 79.77% and 51.3%, respectively, under a 100-kΩ load. Moreover, we perform a Monte Carlo simulation to showcase the impact of transistor variations. Our proposed rectifier, which offers the widest PDR compared to recently-reported designs operating at a similar frequency, is highly adaptable to the varying RF environment, enabling efficient and reliable energy harvesting for Internet of Things devices.

Simulation of Wearable Microstrip Patch Antenna by Using Textile Material for Ambient RF Energy Harvesting

Future enhancements in radio frequency (RF) energy harvesting technology will make easy the creation of a network with no need of dedicated transmitters, as a reliable source of wireless energy power. Recently, the development and employment of wearable antennas has increased rapidly for application in the miniaturization of wireless communication devices. The principal feature of wearable antennas is that they are designed as garment elements able to transmit or receive wireless signals. In this context, we propose a design of a wearable textile microstrip patch antenna operating for wireless body area network (WBAN)at the resonance frequency =2.40GHz. The microstrip patch antenna with an edge feeding technique is designed and simulated by using the Keysight Advanced Design System (ADS) software. Textile materials have a low dielectric constant that reduces the surface wave losses and increases the impedance bandwidth of the antenna. The chosen dielectric substrate in this work is the jeans fabric with relative permittivity of 1.70, thickness of 1.00 mm and dissipation factor of 0.025. The antenna performance parameters are obtained from ADS Momentum. Simulation results show that antenna has the gain of 3.22 dBi and directivity of 8.10 dBi, showing that the wearable textile microstrip antenna has a good performance.

A Co-Planar Waveguide Ultra-Wideband Antenna for Ambient Wi-Fi RF Power Transmission and Energy Harvesting Applications

This study proposes an ultra-wideband antenna for ambient radio frequency (RF) energy harvesting applications. The antenna is based on a co-planar waveguide (CPW) transmission line and incorporates a rectangular slot as an antenna harvester. The proposed antenna utilizes an evolutionary design process to achieve impedance matching of the 50 Ω CPW feeding line over the desired frequency bands. A parametric study investigates CPW elements and rectangular slot size. The harvester antenna is then connected to the primary rectifier circuit of the voltage doubler to examine the signal characteristics. The antenna covers the Industry, Science, and Medicine (ISM) Wi-Fi bands of 2.45 GHz and 5 GHz, achieving a realized gain of 3.641 dBi and 4.644 dBi at 2.45 GHz and 5 GHz, respectively. It exhibits a relatively broad frequency ranging from 2.16 GHz to 6.32 GHz, covering the ultra-wideband fractional bandwidth (FBW) of 105%.

Rectenna structure analysis for ambient RF Energy Harvesting

The paper proposes an efficient structure of RF Energy Harvesting (RFEH) system that can improve efficiency of the system. The paper analysis and indicate relationships between characteristics of the RFEH system such as: center frequency, bandwidth, Q factor, passive gain, and number of rectifier stages. After that, paper proposes design steps to design the RFEH system in which high enough Q and wide bandwidth are guaranteed. The RFEH system is designed and tested to proved the effectiveness of the proposed method. Mesurement results show that a sensitivity of 1V output DC voltage reaches at -20 dBm input power of 950 MHz signal. The power conversion efficiency (PCE) of the system is 57% at -10 dBm input level. The system can generate 3.58 output power when input power of the LTE signal is -19.4 dBm.

Two-Port Five-Band Rectenna for Ultralow Ambient RF Energy Harvesting

A two-port rectenna is proposed to harvest the ambient RF power from five commercial bands, including 1.8 GHz, 2.1 GHz, 2.4 GHz, 2.65 and 3.5 GHz for GSM, LTE, WLAN and 5G, respectively. The novel rectenna comprises a hybrid half-wave rectifier and two back-to-back slot antennas. The rectifier consists of a series rectifier branch and a parallel rectifier branch to extend its multi-band coverage, only sharing one diode. With this design strategy, its RF-DC power conversion efficiency (PCE) can reach 23.1% at 1.8 GHz, 26.4% at 2.1 GHz, 27.2% at 2.4 GHz, 20.7% at 2.66 GHz and 19.1% at 3.47 GHz with -20 dBm input power level. Notably, once a five-tone signal is input simultaneously with the identical power level of -20 dBm, the PCE of rectifying circuit can be improved to 43.7%, breaking the existing record to our best knowledge. The designed slot antennas can also receive omnidirectional RF power at five corresponding frequencies. The experimental results demonstrate that our proposed rectenna is competitive in band coverage and PCE with ultra-low input power, indicating enormous potential for RF energy harvesting and powering sensors, wearables, and other low-power scenarios.

Customizable and upgradable design triple-band dual circular polarization rectenna for ambient RF energy harvesting

A Customizable and upgradable design of triple-band dual circular polarization (CP) rectenna is presented for ambient RF energy harvesting of available frequency bands (i.e., 1800, 2.15, 2.42) efficiently. A broadband dual CP receiving antenna is proposed with a broadband impedance matching bandwidth of 123% from 1 to 4.2 GHZ and axial-ratio (AR) bandwidth of 75% from 1.45 to 3.06 GHz with a maximum gain of 5.54 dBi to cover the selected frequency bands. Besides, the proposed triple-band rectifier with a multi-stub impedance matching network is feasible for RF harvesting with the new design method, and the non-dependence of the resonance frequencies on the distance between the stubs, the rectifier can be easily adjusted for other frequencies. The proposed rectenna’s measurement results show that the generated average dc output voltage and conversion efficiency are improved to 0.8 V and 60%, respectively, at a low RF input power density of −2 dBm for a load resistance of 1.5 kΩ.

High-Performance Multiband Ambient RF Energy Harvesting Front-End System for Sustainable IoT Applications—A Review

The increasing demand for wireless Internet of Things (IoT) calls for power efficient RF energy harvesting approach. The current dominant single-band RF energy harvesting front-end system restricts itself to a single frequency, which is at the risk of ineffective operation when the harvesting frequency is unavailable. This paper reviews and explores the alternative approach of a multiband RF energy-harvesting front-end system. It covers all essential circuitry of a multiband RF energy harvesting front-end system, starting from the recent RF surveys which investigate the typical, usable, and high-strength RF input, to the overview of the state-of-the-art antenna, impedance matching network (IMN), and RF-DC rectifier. The recent advancement of the multiple RF input harvesting abilities, reflection loss minimization, and performance improvement are comprehensively reviewed for different operating conditions, and this review also presents the advantages and disadvantages of the different circuit architecture combinations for multiband RF energy harvesting front-end systems. In summary, this review aims to fill the research gap in the further advancement of multiband RF energy harvesting towards enhancing its performance through optimal circuit integration of the front-end system.

A Compact Broadband Stepped Bow-Tie Antenna for Ambient RF Energy Harvesting

A Compact Broadband Stepped Bow-Tie Antenna for Ambient RF Energy Harvesting

A Capacitive DC-DC Boost Converter with Gate Bias Boosting and Dynamic Body Biasing for an RF Energy Harvesting System

In this paper, a fully integrated capacitive DC-DC boost converter for ultra-low-power internet of things (IoT) applications operating with RF energy harvesting is proposed. A DC-DC boost converter is needed to boost the low output voltage of the RF energy harvester to provide a high voltage to the load. However, a boost converter operating at a low voltage supplied by ambient RF energy harvesting has a problem in that power conversion efficiency is significantly lowered. The proposed on-chip capacitive DC-DC boost converter simultaneously applies gate bias boosting and dynamic body biasing techniques using only the internal boosted voltage without an additional circuit that increases power loss to boost the voltage, achieving high efficiency at an input voltage as low as 0.1 V. The designed capacitive boost converter achieves a peak power conversion efficiency (PCE) of 33.8% at a very low input voltage of 0.1 V, a 14% improvement over the peak PCE of the conventional cross-coupled charge pump. A maximum peak PCE of 80.1% is achieved at an input voltage of 200 mV and a load current of 3 μA. The proposed capacitive boost converter is implemented with a total flying capacitance of 60 pF, suitable for on-chip integration.

A Novel High-Sensitivity Broadband Rectifier for Ambient RF Energy Harvesting

A Novel High-Sensitivity Broadband Rectifier for Ambient RF Energy Harvesting

Considerations for the Design and Implementation of Ambient RF Signal Rectifiers in the 2.45 GHz WiFi Band

Ambient RF energy harvesting (RF-EH) is a particular case of wireless power transfer (WPT), which is characterized by ultra-low power operation. This work points out theoretical and practical aspects that should be considered in the design of RF rectifiers for ambient RF energy harvesting systems. The most common RF rectifier circuits are compared and discussed using simulations and experimental data. The efficiency is analyzed in terms of the input power and load resistance. It is demonstrated that the most efficient RF rectifier in ultra-low power conditions is the simple diode capacitor structure. As an illustrative example, an RF rectifier has been fabricated by designing an impedance-matching network to operate into the WIFI band. The fabricated prototype shows a measured 12% efficiency working at 2.47 GHz with around −30 dBm ambient input power, which is higher than the reported efficiencies in the literature. The fabricated energy harvesting system delivers power between 25.6 nW and 129.6 nW to a resistive 10 kΩ load. The obtained results are applicable to ambient RF up to 6 GHz.

A Fully-Integrated Ambient RF Energy Harvesting System with 423-μW Output Power

This paper proposes a 2.4-GHz fully-integrated single-frequency multi-channel RF energy harvesting (RFEH) system with increased harvested power density. The RFEH can produce an output power of ~423-μW in harvesting ambient RF energy. The front-end consists of an on-chip impedance matching network with a stacked rectifier concurrently matched to a 50 Ω input source. The circuit mitigates the “dead-zone” by enhancing the pumping efficiency, achieved through the increase of Vgs drivability of the proposed internal gate boosting 6-stage low-input voltage charge pump and the 5-stage shared-auxiliary-biasing ring-voltage-controlled-oscillator (VCO) integrated to improve the start-up. The RFEH system, simulated in 180-nm complementary metal–oxide–semiconductor (CMOS), occupies an active area of 1.02 mm2. Post-layout simulations show a peak power conversion efficiency(PCE) of 21.15%, driving a 3.3-kΩ load at an input power of 0 dBm and sensitivity of −14.1 dBm corresponding to an output voltage, Vout,RFEH of 1.25 V.