Airborne Particle Number Concentration Research Articles

Quantifying the reduction of airborne infectious viral load using a ventilated patient hood

Healthcare workers treating SARS-CoV-2 patients are at risk of infection by respiratory exposure to patient-emitted, virus-laden aerosols. Source control devices such as ventilated patient isolation hoods have been shown to limit the dissemination of non-infectious airborne particles in laboratory tests, but data on their performance in mitigating the airborne transmission risk of infectious viruses are lacking. We used an infectious airborne virus to quantify the ability of a ventilated hood to reduce infectious virus exposure in indoor environments. We nebulized 109 plaque forming units (pfu) of bacteriophage PhiX174 virus into a ∼30-m3 room when the hood was active or inactive. The airborne concentration of infectious virus was measured by BioSpot-VIVAS and settle plates using plaque assay quantification on the bacterial host Escherichia coli C. The airborne particle number concentration (PNC) was also monitored continuously using an optical particle sizer. The median airborne viral concentration in the room reached 1.41× 105pfu/m3 with the hood inactive. When active, the hood reduced infectious virus concentration in air samples by 374-fold. The deposition of infectious virus on the surface of settle plates was reduced by 87-fold. This was associated with a 109-fold reduction in total airborne particle number escape rate. A personal ventilation hood significantly reduced airborne particle escape, considerably lowering infectious virus contamination in an indoor environment. Our findings support the further development of source control devices to mitigate nosocomial infection risk among healthcare workers exposed to airborne viruses in clinical settings.

Occupational Exposure and Environmental Release: The Case Study of Pouring TiO2 and Filler Materials for Paint Production.

Pulmonary exposure to micro- and nanoscaled particles has been widely linked to adverse health effects and high concentrations of respirable particles are expected to occur within and around many industrial settings. In this study, a field-measurement campaign was performed at an industrial manufacturer, during the production of paints. Spatial and personal measurements were conducted and results were used to estimate the mass flows in the facility and the airborne particle release to the outdoor environment. Airborne particle number concentration (1 × 103–1.0 × 104 cm−3), respirable mass (0.06–0.6 mg m−3), and PM10 (0.3–6.5 mg m−3) were measured during pouring activities. In overall; emissions from pouring activities were found to be dominated by coarser particles >300 nm. Even though the raw materials were not identified as nanomaterials by the manufacturers, handling of TiO2 and clays resulted in release of nanometric particles to both workplace air and outdoor environment, which was confirmed by TEM analysis of indoor and stack emission samples. During the measurement period, none of the existing exposure limits in force were exceeded. Particle release to the outdoor environment varied from 6 to 20 g ton−1 at concentrations between 0.6 and 9.7 mg m−3 of total suspended dust depending on the powder. The estimated release of TiO2 to outdoors was 0.9 kg per year. Particle release to the environment is not expected to cause any major impact due to atmospheric dilution

Quantitative filter forensics: Size distribution and particulate matter concentrations in residential buildings.

We applied filter forensics, the analysis of dust from the heating, ventilation, and air-conditioning (HVAC) filters, to measure particle size distribution in 21 residences in Toronto, Canada over a year. Four filters with different nominal efficiencies (Minimum Efficiency Reporting Value (MERV) 8-14 from ASHRAE Standard 52.2) were deployed in each residence each for three months, while the effective filtration volumes (the product of flow rate, runtime, and in-situ filter efficiency) were characterized over each filter lifetime. Using extraction and laser diffraction, we found that approximately 90% of the volumetric distributions were >10µm and the volume median diameter (VMD) ranged from 23.4 to 75.1µm. Using quantitative filter forensics (QFF), total suspended particle (TSP) concentrations ranged from 2.9 to 823.7µg/m3 (median=89.8µg/m3 ) with a moderate correlation with the content of TSP on the filters (in terms of g) and with the TSP effective filtration volume (m3 ) indicating the importance of both filter forensics and HVAC metadata parameters to QFF concentration estimates. There was no strong correlation between PM10 or PM2.5 concentrations and hourly airborne particle number concentrations measured by low-cost sensors suggesting an evaluation of QFF is warranted, particularly for the exploration of smaller particles.

Calibration of optical particle counters: first comprehensive inter-comparison for particle sizes up to 5 µm and number concentrations up to 2 cm−3

We report on an inter-laboratory comparison for the calibration of light-scattering optical particle counters measuring the number concentration of airborne particles in the size range 300 nm–5 µm. This comparison, registered as EURAMET pilot study Nr. 1453, is an important first step towards internationally recognized SI traceability in the measurement of low particle number concentrations encountered in clean-room facilities. The participating particle metrology laboratories of NMIJ (Japan), DFM (Denmark) and METAS (Switzerland) each provided a portable optical particle counter as a transfer standard to be circulated amongst the partners. The comparison covered particle number concentrations up to about 2 cm−3. The individual measurements for the transfer standards at each laboratory are in good agreement with the reference value, typically within 7%, which supports the applied national primary methods of measurement.

A Bayesian spatiotemporal model of panel design data: Airborne particle number concentration in Brisbane, Australia

AbstractIn environmental monitoring, the ability to obtain high‐quality data across space and time is often limited by the cost of purchasing, deploying and maintaining a large collection of equipment, and the employment of personnel to perform these tasks. An ideal design for a monitoring campaign would be dense enough in time to capture short‐range variation at each site, long enough in time to examine trends at each site and across all sites, and dense enough in space to allow modelling of the relationship between the means at each of the sites. This paper outlines a methodology for semiparametric spatiotemporal modelling of data that is dense in time but sparse in space, obtained from a split panel design, the most feasible approach to covering space and time with limited equipment. The data are hourly averaged particle number concentration (PNC) and were collected as part of the International Laboratory for Air Quality and Health's Ultrafine Particles from Traffic Emissions and Children's Health (UPTECH) project. The panel design comprises two weeks of continuous measurements taken at each of a number of government primary schools in the Brisbane Metropolitan Area, with each school visited sequentially. The school data are augmented by data from long‐term monitoring stations at three locations in Brisbane, Australia. The temporal part of the model explains daily and weekly cycles in PNC at the schools. The temporal variation is modelled hierarchically with a penalised random walk term common to all sites and a similar term accounting for the remaining temporal trend at each site. The modelling of temporal trends requires an acknowledgement that the observations are correlated rather than independent. At each school and long‐term monitoring site, peaks in PNC can be attributed to the morning and afternoon rush hour traffic and new particle formation events. The spatial component of the model describes the school‐to‐school variation in mean PNC at each school and within each school ground. The spatial term in the model is derived from a stochastic partial differential equation and approximates a Gaussian process with a Gaussian Markov Random field. Fitting the model helps describe spatial and temporal variability at a subset of the UPTECH schools and the long‐term monitoring sites, which can be used to estimate the exposure of school children to ultrafine particles. Parameter estimates and their uncertainty are computed in a computationally efficient approximate Bayesian inference environment, R‐INLA.

Investigation of indoor air quality determinants in a field study using three different data streams

Indoor air quality (IAQ) is determined by indoor and outdoor sources and conditions, building characteristics, and occupant behavior. In the field study context where the researcher lacks full control of observational conditions, it is difficult to compare and integrate these determinants because they require such different types and sources of data. This pilot-level project investigated the potential to overcome these limitations by integrating traditional IAQ measurement techniques with questionnaires and analysis of building deficiencies using 3D infrared thermography imaging in two residential multi-apartment buildings. Of the building deficiencies detected by the 3D thermography, missing insulation (MI) correlated best with the IAQ measurements and questionnaire data. Apartments missing more than 5% of insulation in their exterior wall (n = 6) had a significantly higher number concentration of ultrafine airborne particles (diameter < 300 nm) (p = 0.013) and their indoor/outdoor ratio (p = 0.029) compared to apartments where less than 5% of insulation was missing (n = 14). The correlation was driven by apartments where no smoking or use candles or incense was reported. Ultrafine particle concentrations in apartments with combustion sources were higher regardless of the levels of MI. Corner apartments had a higher fraction of MI compared to non-corner apartments (p = 0.002); higher levels of MI were detected in apartments where a resident had an asthma attack in the past 12 months. Our data suggest that integration of different data streams produces a more informative IAQ investigation. This pilot-level study should be performed on a larger scale to examine its wider applicability in the IAQ field.

Evolution of particle interactions between accidentally released aerosol particles generated from powdered engineered nanomaterials into a simulated workplace atmosphere

The evaluation of aerosol processes which alter the size distribution of accidentally released nanomaterial particles in an indoor environment can provide size resolved exposure estimations, and subsequently contribute to a more comprehensive risk analysis on engineered nanomaterials (ENMs). In this work processed suspensions of TiO2 and SiO2 nanopowders were introduced into the reservoir of a nebuliser, and injected continuously as nano-aerosols into a room-size dispersion facility for a fixed release time. Following injection, the concentration of the dispersed aerosols was allowed to naturally decay for a prolonged period. Airborne particle number concentration (PNC) and particle size distributions (PSD) were continuously measured at a point within the breathing zone near to the source, while deposited particles were collected for transmission electron microscopy (TEM) analysis. A log10-normal fitting program was used to determine the evolution of the modal groups present within the measured PSDs. A modelling approach that considered the experimentally determined particle decay rate as a sum of the pair to pair coagulation and deposition rates was employed to estimate the relative importance of size-resolved deposition compared to coagulation. Results indicated that the variation of PNC with time was accurately modelled, providing size-dependent insights into the contribution of the two particle removal mechanisms to the change of PNC over time. The deposition patterns obtained from the TEM images qualitatively supported the model results. Since a limited set of input parameters were used, we concluded that the proposed model could be an effective tool for a reasonable quantification of worker's exposure to aerosols originating from the accidental release of diffuse ENM in real workplaces.

Evaluation of emissions and exposures at workplaces using desktop 3-dimensional printers

There is a paucity of data on additive manufacturing process emissions and personal exposures in real-world workplaces. Hence, we evaluated atmospheres in four workplaces utilizing desktop "3-dimensional" (3-d) printers [fused filament fabrication (FFF) and sheer] for production, prototyping, or research. Airborne particle diameter and number concentration and total volatile organic compound concentrations were measured using real-time instruments. Airborne particles and volatile organic compounds were collected using time-integrated sampling techniques for off-line analysis. Personal exposures for metals and volatile organic compounds were measured in the breathing zone of operators. All 3-d printers that were monitored released ultrafine and fine particles and organic vapors into workplace air. Particle number-based emission rates (#/min) ranged from 9.4 × 109 to 4.4 × 1011 (n = 9samples) for FFF3-d printers and from 1.9 to 3.8 × 109 (n = 2 samples) for a sheer 3-d printer. The large variability in emission rate values reflected variability from the printers as well as differences in printer design, operating conditions, and feedstock materials among printers. A custom-built ventilated enclosure evaluated at one facility was capable of reducing particle number and total organic chemical concentrations by 99.7% and 53.2%, respectively. Carbonyl compounds were detected in room air; however, none were specifically attributed to the 3-d printing process. Personal exposure to metals (aluminum, iron) and 12 different organic chemicals were all below applicable NIOSH Recommended Exposure Limit values, but results are not reflective of all possible exposure scenarios. More research is needed to understand 3-d printer emissions, exposures, and efficacy of engineering controls in occupational settings.

Impact of air-handling system exhaust failure on dissemination pattern of simulant pathogen particles in a clinical biocontainment unit.

Biocontainment units (BCUs) are facilities used to care for patients with highly infectious diseases. However, there is limited guidance on BCU protocols and design. This study presents the first investigation of how HVAC (heating, ventilation, air‐conditioning) operating conditions influence the dissemination of fluorescent tracer particles released in a BCU. Test conditions included normal HVAC operation and exhaust failure resulting in loss of negative pressure. A suspension of optical brightener powder and water was nebulized to produce fluorescent particles simulating droplet nuclei (0.5‐5 μm). Airborne particle number concentrations were monitored by Instantaneous Biological Analyzers and Collectors (FLIR Systems). During normal HVAC operation, fluorescent tracer particles were contained in the isolation room (average concentration = 1 × 104 ± 3 × 103/Lair). Under exhaust failure, the automated HVAC system maximizes airflow into areas adjacent to isolation rooms to attempt to maintain negative pressure differential. However, 6% of the fluorescent particles were transported through cracks around doors/door handles out of the isolation room via airflow alone and not by movement of personnel or doors. Overall, this study provides a systematic method for evaluating capabilities to contain aerosolized particles during various HVAC scenarios. Recommendations are provided to improve situation‐specific BCU safety.

Development of a biotechnological platform based on protein production for biological control strategies for banana crop pathogens

There is a paucity of data on additive manufacturing process emissions and personal exposures in real-world workplaces. Hence, we evaluated atmospheres in four workplaces utilizing desktop “3-dimensional” (3-d) printers [fused filament fabrication (FFF) and sheer] for production, prototyping, or research. Airborne particle diameter and number concentration and total volatile organic compound concentrations were measured using real-time instruments. Airborne particles and volatile organic compounds were collected using time-integrated sampling techniques for off-line analysis. Personal exposures for metals and volatile organic compounds were measured in the breathing zone of operators. All 3-d printers that were monitored released ultrafine and fine particles and organic vapors into workplace air. Particle number-based emission rates (#/min) ranged from 9.4 × 109 to 4.4 × 1011 (n = 9 samples) for FFF 3-d printers and from 1.9 to 3.8 × 109 (n = 2 samples) for a sheer 3-d printer. The large variability in emission rate values reflected variability from the printers as well as differences in printer design, operating conditions, and feedstock materials among printers. A custom-built ventilated enclosure evaluated at one facility was capable of reducing particle number and total organic chemical concentrations by 99.7% and 53.2%, respectively. Carbonyl compounds were detected in room air; however, none were specifically attributed to the 3-d printing process. Personal exposure to metals (aluminum, iron) and 12 different organic chemicals were all below applicable NIOSH Recommended Exposure Limit values, but results are not reflective of all possible exposure scenarios. More research is needed to understand 3-d printer emissions, exposures, and efficacy of engineering controls in occupational settings.

In vitro toxicological evaluation of surgical smoke from human tissue

BackgroundOperating room personnel have the potential to be exposed to surgical smoke, the by-product of using electrocautery or laser surgical device, on a daily basis. Surgical smoke is made up of both biological by-products and chemical pollutants that have been shown to cause eye, skin and pulmonary irritation.MethodsIn this study, surgical smoke was collected in real time in cell culture media by using an electrocautery surgical device to cut and coagulate human breast tissues. Airborne particle number concentration and particle distribution were determined by direct reading instruments. Airborne concentration of selected volatile organic compounds (VOCs) were determined by evacuated canisters. Head space analysis was conducted to quantify dissolved VOCs in cell culture medium. Human small airway epithelial cells (SAEC) and RAW 264.7 mouse macrophages (RAW) were exposed to surgical smoke in culture media for 24 h and then assayed for cell viability, lactate dehydrogenase (LDH) and superoxide production.ResultsOur results demonstrated that surgical smoke-generated from human breast tissues induced cytotoxicity and LDH increases in both the SAEC and RAW. However, surgical smoke did not induce superoxide production in the SAEC or RAW.Conclusion These data suggest that the surgical smoke is cytotoxic in vitro and support the previously published data that the surgical smoke may be an occupational hazard to healthcare workers.

Estimation of inhaled airborne particle number concentration by subway users in Seoul, Korea

Exposure to airborne particulate matter (PM) causes several diseases in the human body. The smaller particles, which have relatively large surface areas, are actually more harmful to the human body since they can penetrate deeper parts of the lungs or become secondary pollutants by bonding with other atmospheric pollutants, such as nitrogen oxides. The purpose of this study is to present the number of PM inhaled by subway users as a possible reference material for any analysis of the hazards to the human body arising from the inhalation of such PM. Two transfer stations in Seoul, Korea, which have the greatest number of users, were selected for this study. For 0.3–0.422 μm PM, particle number concentration (PNC) was highest outdoors but decreased as the tester moved deeper underground. On the other hand, the PNC between 1 and 10 μm increased as the tester moved deeper underground and showed a high number concentration inside the subway train as well. An analysis of the particles to which subway users are actually exposed to (inhaled particle number), using particle concentration at each measurement location, the average inhalation rate of an adult, and the average stay time at each location, all showed that particles sized 0.01–0.422 μm are mostly inhaled from the outdoor air whereas particles sized 1–10 μm are inhaled as the passengers move deeper underground. Based on these findings, we expect that the inhaled particle number of subway users can be used as reference data for an evaluation of the hazards to health caused by PM inhalation.

Performance study of portable devices for the real-time measurement of airborne particle number concentration and size (distribution)

The aim of this experimental study was to investigate the performance of both portable and transportable devices devoted to the real-time measurement of airborne particle number concentration and size (distribution). Electrical mobility spectrometers (SMPS, FMPS, Nanoscan) as well as diffusion chargers (DiSCmini, Nanotracer) were studied. Both monodisperse and polydisperse aerosols were produced within the CAIMAN facility to challenge the instruments. The monodisperse test aerosols were selected in the 15-400 nm diameter range using a differential mobility analyser (DMA), and presented number concentrations of between 6.102 and 2.105 cm−3. The polydisperse test aerosols presented modal diameters of between 8 and 270 nm and number concentrations between 4.103 to 106 cm−3. The behavior of the different devices is expressed as (1) the ratio of the reported diameter to the reference diameter, and (2) the ratio of the reported number concentration to the reference concentration. These results are displayed as boxplots to better represent the statistical distribution of the experimental results. For the group of electrical mobility spectrometers, a good agreement between SMPS and FMPS and the reference was demonstrated. A slight tendency for the Nanoscan to underestimate particle size distribution for particles above around 100 nm was observed. The data reported for the group of diffusion chargers demonstrate that all, except the Nanotracer, show a tendency to underestimate particle diameter, by a factor around −40% to −10%. In the case of particle concentration, larger deviations were observed.

Factors controlling particle number concentration and size at metro stations

An extensive air quality campaign was performed at differently designed station platforms in the Barcelona metro system, aiming to investigate the factors governing airborne particle number (N) concentrations and their size distributions. The study of the daily trends of N concentrations by different size ranges shows that concentrations of N0.3–10 are closely related with the schedule of the metro service. Conversely, the hourly variation of N0.007–10 (mainly composed of ultrafine particles) could be partly governed by the entrance of particles from outdoor emissions through mechanical ventilation. Measurements under different ventilation settings at three metro platforms reveal that the effect on air quality linked to changes in the tunnel ventilation depends on the station design. Night-time maintenance works in tunnels are frequent activities in the metro system; and after intense prolonged works, these can result in higher N concentrations at platforms during the following metro operating hours (by up to 30%), this being especially evident for N1–10. Due to the complex mixture of factors controlling N, together with the differences in trends recorded for particles within different size ranges, developing an air quality strategy at metro systems is a great challenge. When compared to street-level urban particles concentrations, the priority in metro air quality should be dealing with particles coarser than 0.3 μm. In fact, the results suggest that at narrow platforms served by single-track tunnels the current forced tunnel ventilation during operating hours is less efficient in reducing coarse particles compared to fine.

Real-Time Ultrafine Aerosol Measurements from Wastewater Treatment Facilities.

Airborne particle emissions from wastewater treatment plants (WWTP) have been associated with health repercussions but particulate quantification studies are scarce. In this study, particulate matter (PM) number concentrations and size distributions in the ultrafine range (7-300 nm) were measured from two different sources: a laboratory-scale aerobic bioreactor and the activated sludge aeration basins at Orange County Sanitation District (OCSD). The relationships between wastewater parameters (total organic carbon (TOC), chemical oxygen demand (COD), and total suspended solids (TSS)), aeration flow rate and particle concentrations were also explored. A significant positive relationship was found between particle concentration and WWTP variables (COD: r(10) = 0.876, p <.001, TOC: r(10) = 0.664, p <.05, TSS: r(10) = 0.707, p <.05, aeration flow rate: r(8) = 0.988, p <.0001). A theoretical model was also developed from empirical data to compare real world WWTP aerosol number emission fluxes with laboratory data. Aerosol number fluxes at OCSD aerated basins (9.8 × 104 lbs/min·cm2) and the bioreactor (7.95 × 104 lbs/min·cm2) were calculated and showed a relatively small difference (19%). The ultrafine size distributions from both systems were consistent, with a mode of ∼48 nm. The average mass concentration (7.03 μg/cm3) from OCSD was relatively small compared to other urban sources. However, the in-tank average number concentration of airborne particles (14 480 lbs/cm3) was higher than background ambient concentrations.

A System to Create Stable Nanoparticle Aerosols from Nanopowders

Nanoparticle aerosols released from nanopowders in workplaces are associated with human exposure and health risks. We developed a novel system, requiring minimal amounts of test materials (min. 200 mg), for studying powder aerosolization behavior and aerosol properties. The aerosolization procedure follows the concept of the fluidized-bed process, but occurs in the modified volume of a V-shaped aerosol generator. The airborne particle number concentration is adjustable by controlling the air flow rate. The system supplied stable aerosol generation rates and particle size distributions over long periods (0.5-2 hr and possibly longer), which are important, for example, to study aerosol behavior, but also for toxicological studies. Strict adherence to the operating procedures during the aerosolization experiments ensures the generation of reproducible test results. The critical steps in the standard protocol are the preparation of the material and setup, and the aerosolization operations themselves. The system can be used for experiments requiring stable aerosol concentrations and may also be an alternative method for testing dustiness. The controlled aerosolization made possible with this setup occurs using energy inputs (may be characterized by aerosolization air velocity) that are within the ranges commonly found in occupational environments where nanomaterial powders are handled. This setup and its operating protocol are thus helpful for human exposure and risk assessment.

A System to Create Stable Nanoparticle Aerosols from Nanopowders

Nanoparticle aerosols released from nanopowders in workplaces are associated with human exposure and health risks. We developed a novel system, requiring minimal amounts of test materials (min. 200 mg), for studying powder aerosolization behavior and aerosol properties. The aerosolization procedure follows the concept of the fluidized-bed process, but occurs in the modified volume of a V-shaped aerosol generator. The airborne particle number concentration is adjustable by controlling the air flow rate. The system supplied stable aerosol generation rates and particle size distributions over long periods (0.5-2 hr and possibly longer), which are important, for example, to study aerosol behavior, but also for toxicological studies. Strict adherence to the operating procedures during the aerosolization experiments ensures the generation of reproducible test results. The critical steps in the standard protocol are the preparation of the material and setup, and the aerosolization operations themselves. The system can be used for experiments requiring stable aerosol concentrations and may also be an alternative method for testing dustiness. The controlled aerosolization made possible with this setup occurs using energy inputs (may be characterized by aerosolization air velocity) that are within the ranges commonly found in occupational environments where nanomaterial powders are handled. This setup and its operating protocol are thus helpful for human exposure and risk assessment.

Impact of bedding arrangements, pillows, and blankets on particle resuspension in the sleep microenvironment

The risk of exposure to pollutants in mattress dust is enhanced by the extended period that people spend every day in their sleep microenvironments. Epidemiological studies have shown strong associations between exposure to these pollutants and health risks. Blankets, pillows, and mattresses have been considered as major sources of accumulated dust particles, which may become airborne through a process known as resuspension. Therefore, a better understanding of the impact of bedding arrangements on human-induced particle resuspension in the sleep microenvironment is needed. In this investigation, participants performed sets of prescribed movements on an artificially-seeded mattress. Ten different bedding arrangements were examined. Airborne particle number concentrations were measured to estimate size-resolved resuspension rates (RR). Across all particle sizes and bedding arrangements, RRs ranged from 10−3to 101 h−1, with higher RRs associated with larger particles. RRs for a seeded pillow were greater than RRs for a seeded blanket or seeded mattress. The use of an additional pillow cover did act as an effective barrier to the penetration of larger particles deposited on the underlying pillow surface. Additionally, blankets were not found to be a significant barrier for particles resuspended from the underlying seeded mattress. Intake fractions (iF) were in the range of 102to 104 ppm (10−4to 10−2 on a fractional basis), suggesting a significant fraction of released particles can reach the breathing zone region. The highest iF was estimated for an arrangement where both a pillow and a mattress were seeded without a blanket present (104 ppm).

Particle deposition study in a horizontal turbulent duct flow using optical microscopy and particle size spectrometry

A new technique based on optical microscopy and particle size spectrometry is here presented to investigate deposition of aerosol particles. Micron-sized monodisperse liquid particles were injected in a horizontal duct flow. The turbulent flow field was recorded using Particle Image Velocimetry. The airborne particle size and number concentration was determined by isokinetic sampling in combination with an Aerodynamic Particle Sizer (APS). The surface deposited particles were counted by means of optical microscopy, which was found to be a robust and simple recording method. The particle deposition velocity was directly determined out of the number of deposited particles detected by the microscope and the airborne particle number concentration recorded by the APS. The present results show good agreement with similar studies and prove the potential of optical microscopy for the detection of wall deposited particles in comparison to the more complex and expensive methods such as fluorescence based wet chemistry or neutron activation techniques.

Evaluation of airborne particle emissions from commercial products containing carbon nanotubes

The emission of the airborne particles from epoxy resin test sticks with different CNT loadings and two commercial products were characterized while sanding with three grit sizes and three disc sander speeds. The total number concentrations, respirable mass concentrations, and particle size number/mass distributions of the emitted particles were measured using a condensation particle counter, an optical particle counter, and a scanning mobility particle sizer. The emitted particles were sampled on a polycarbonate filter and analyzed using electron microscopy. The highest number concentrations (arithmetic mean = 4670 particles/cm(3)) were produced with coarse sandpaper, 2% (by weight) CNT test sticks and medium disc sander speed, whereas the lowest number concentrations (arithmetic mean = 92 particles/cm(3)) were produced with medium sandpaper, 2% CNT test sticks and slow disc sander speed. Respirable mass concentrations were highest (arithmetic mean = 1.01 mg/m(3)) for fine sandpaper, 2% CNT test sticks and medium disc sander speed and lowest (arithmetic mean = 0.20 mg/m(3)) for medium sandpaper, 0% CNT test sticks and medium disc sander speed. For CNT-epoxy samples, airborne particles were primarily micrometer-sized epoxy cores with CNT protrusions. No free CNTs were observed in airborne samples, except for tests conducted with 4% CNT epoxy. The number concentration, mass concentration, and size distribution of airborne particles generated when products containing CNTs are sanded depends on the conditions of sanding and the characteristics of the material being sanded.