Air Volume Research Articles

Bionic noise reduction design of axial fan impeller

Abstract Fans are integral equipment widely employed in both industrial settings and daily life. However, a persistent challenge in their design lies in the inherent conflict between aerodynamic performance and noise levels. Improving aerodynamic efficiency often results in a compromise of acoustic performance. To tackle this issue, we employed the bionic design method to craft a novel axial fan impeller featuring a bionic curved hub and bionic serrated leading edges. The impact of structural optimization on the aerodynamic and acoustic properties of the impeller, as well as the influence of optimization parameters on these properties, were systematically investigated through numerical simulations. The bionic impeller was then fabricated using 3D printing, and its aerodynamic and noise performance were experimentally evaluated by integrating it into an external air conditioner. Comparison of the flow field and sound field data between the optimized and prototype impellers revealed noteworthy outcomes. The curved wall at the bionic hub's tail effectively diminished the pressure gradient on the hub surface, directing the airflow toward the rear end of the hub. This design enhancement significantly reduced the turbulent area behind the prototype impeller's hub. Additionally, the bionic serrated structure, when appropriately designed, demonstrated its efficacy in reducing the contact area between the blade's leading edge and incoming flow. This led to the dispersion of stress concentrations and the inhibition of strong turbulence generation. Notably, the experimental results indicated a 3.7% increase in air volume flow rate and a 2.3dB reduction in noise for the optimized impeller compared to the prototype. This successful mitigation of the trade-off between aerodynamic performance and noise level underscores the effectiveness of our bionic design approach.

Power Augmentation of Gas Turbine Using Exhaust Flue Gas Operated Vapor Absorption Machine

Industrial gas turbines (GT) that operate at constant speed are constant-volume-flow combustion machines. As the specific volume of air is directly proportional to the temperature, an increase in air density results in a higher air mass flow rate at low air ambient temperatures. This results more mass of air is now passes through same volume gas turbine space. Consequently, the gas turbine power output increases proportionally with the increase in air mass flow rate. For geographic regions where warm and humid months are predominant throughout the year, significant power loss occurs during these months, and a higher rate of expensive fuel is fired at reduced power output. A gas turbine inlet air cooling technique is a useful option to enhance GT output. One of the innovative options for power augmentation of gas turbine is inlet air conditioning using a vapor absorption machine (VAM). Using VAM for GT intake air conditioning has the advantage over other systems in that it can be operated from waste heat. Many gas turbine machines, particularly natural gas pumping stations, are operated without heat recovery steam generator (HRSG) or heat recovery option. Valuable heat energy is escaped with exhaust flue gas in these systems. This paper demonstrates how GT exhaust waste heat can be utilized for its own power generation enhancement. In this study, a flue gas-based vapor absorption machine is selected for cooling the inlet air of a 26 MW gas turbine, which is used to drive the booster compressor of a natural gas pumping station. The capacity of the VAM for the required cooling effect has been calculated. The expected GT power enhancement from intake air gas conditioning has also been estimated in this paper.

Regional Pulmonary Ventilation Assessment Method and System Based on Impedance Sensing Information from the Pentapulmonary Lobes

Regional lung ventilation assessment is a critical tool for the early detection of lung diseases and postoperative evaluation. Biosensor-based impedance measurements, known for their non-invasive nature, among other benefits, have garnered significant attention compared to traditional detection methods that utilize pressure sensors. However, solely utilizing overall thoracic impedance fails to accurately capture changes in regional lung air volume. This study introduces an assessment method for lung ventilation that utilizes impedance data from the five lobes, develops a nonlinear model correlating regional impedance with lung air volume, and formulates an approach to identify regional ventilation obstructions based on impedance variations in affected areas. The electrode configuration for the five lung lobes was established through numerical simulations, revealing a power–function nonlinear relationship between regional impedance and air volume changes. An analysis of 389 pulmonary function tests refined the equations for calculating pulmonary function parameters, taking into account individual differences. Validation tests on 30 cases indicated maximum relative errors of 0.82% for FVC and 0.98% for FEV1, all within the 95% confidence intervals. The index for assessing regional ventilation impairment was corroborated by CT scans in 50 critical care cases, with 10 validation trials showing agreement with CT lesion localization results.

Unveiling overlooked aspects of model predictive control for building air conditioning systems

The ongoing research on model predictive control (MPC) for building air conditioning systems predominantly centers on improving the predictive capabilities of system models. In this paper, the impacts of three additional pivotal factors on MPC performance are assessed by examining a generic MPC design for a typical variable air volume (VAV) system that serves large commercial buildings. The three factors encompass the nuanced reformulation of optimization, the judicious relaxation of constraints, and the meticulous tuning of parameters. Detailed case studies with an integrated Modelica and EnergyPlus model of the US Department of Energy's Commercial Reference Building are conducted. The results confirm that the optimization formulation, along with relaxation methods, significantly affects MPC performance in terms of energy savings, zonal thermal comfort level, and computational demand. They also reveal that the impact of the MPC control parameters on the energy savings and thermal comfort may vary by season and can be non-monotonic.

Experimental and numerical study on multiphase fluid dynamics of coal and blends with biomass (sugarcane bagasse) in a lab-scale full-loop circulating fluidized bed gasifier

ABSTRACT The current research presents a 3-D hydrodynamic simulation of the fluidized bed riser with a validated CFD model at different superficial gas velocities and inventory composition (coal of 2 kg is blended with sugarcane bagasse weights 0.2 kg and 0.8 kg). The experiments are performed by varying superficial gas velocity (0.5 Umf to 3 Umf), coal particle size (460 μm and 460 μm), and coal bed inventory size (1.5 kg and 2 kg) in a pilot-scale circulating fluidized bed riser of 100 mm diameter and 3000 mm height. The CFD model results are in good agreement with experimental pressure drop and solid volume fraction. The effect of drag and lift force in fluidization hydrodynamics has been studied. The validated CFD model is then extended to predict the hydrodynamics of the three-fluid, coal-sugarcane bagasse-air system. A mixing factor is defined to quantify the mixing behavior of coal and sugarcane bagasse. It is concluded that a 200 gm sugarcane bagasse blend has good mixing than the 800 gm blends. For efficient mixing, coal and sugarcane bagasse fluidized beds should operate in the 2 Umf to 4 Umf superficial gas velocity range. The results of axial and radial distribution of coal, sugarcane bagasse and air volume fraction, pressure drop, slip velocity, and fluidized bed heights are presented.

Effluent quality improvement in sequencing batch reactor-based wastewater treatment processes using advanced control strategies

ABSTRACT The treatment of wastewater is highly challenging due to large fluctuations in flowrates, pollutants, and variable influent water compositions. A sequencing batch reactor (SBR) and modified SBR cycle-step-feed process (SSBR) configuration are studied in this work to effectively treat municipal wastewater while simultaneously removing nitrogen and phosphorus. To control the amount of dissolved oxygen in an SBR, three axiomatic control strategies (proportional integral (PI), fractional proportional integral (FPI), and fuzzy logic controllers) are presented. A biological process and relevant control algorithm has been designed using real-time plant data with the models of SBR and SSBR using the ASM2d mathematical model. On comparison, FPI showed a significant reduction in nutrient levels and added an improvement in effluent quality. The overall effluent quality is improved by 0.86% in FPI in comparison with PI controller. The SSBR, which was improved by precisely optimizing nutrient supply and aeration, establishes a delicate equilibrium. This refined method reduces oxygen requirements while reliably sustaining important biological functions. Focusing solely on the FPI controller's performance in terms of total air volume consumption, the step-feed SBR mechanism achieves an excellent 11.04% reduction in consumption.

Investigation of a hybrid two-layered channel-jet heat sink for air cooling

With the miniaturization and deep integration of electronics, the challenges associated with high-power heat dissipation technology have increased. Combining the features of jet cooling technology and microchannel cooling technology, a hybrid two-layered channel-jet heat sink is designed for general consumer CPUs. The heat sink performance is investigated experimentally. Since the CPU generation power is 120 W, the heat sink can control the CPU excess temperature below 60 °C with an air volume less than 20 m3/h and a pressure drop less than 20 Pa. The different geometric parameters of the heat sink are numerically calculated. Increasing the channel width and reducing the channel height and slot length can enhance the heat transfer but also increase the pressure drop. Orthogonal tests are employed to optimize the design by evaluating the performance of various heat sink structures. The performance evaluation criterion (PEC) is selected as the evaluation index. Under standard conditions with a cross-sectional airflow velocity of 1.5 m/s, the optimal structure is a 2 mm channel width, 12 mm channel height and 50 mm slot length.

A forced aeration system for microbial culture of multiple shaken vessels suppresses volatilization.

Shake-flask culture, an aerobic submerged culture, has been used in various applications involving cell cultivation. However, it is not designed for forced aeration. Hence, this study aimed to develop a small-scale submerged shaking culture system enabling forced aeration into the medium. A forced aeration control system for multiple vessels allows shaking, suppresses volatilization, and is attachable externally to existing shaking tables. Using a specially developed plug, medium volatilization was reduced to less than 10%, even after 45h of continuous aeration (~ 60mL/min of dry air) in a 50mL working volume. Escherichia coli IFO3301cultivation with aeration was completed within a shorter period than that without aeration, with a 35% reduction in the time-to-reach maximum bacterial concentration (26.5g-dry cell/L) and a 1.25-fold increase in maximum concentration. The maximum bacterial concentration achieved with aeration was identical to that obtained using the Erlenmeyer flask, with a 65% reduction in the time required to reach it.

9 Use of new technology to measure methane emissions

Abstract Over recent decades, the impact of human-induced climate change and the role of ruminant agriculture has been of growing concern for both the public and the scientific community. This has led to rapid advancements in technology needed to measure methane emissions accurately and precisely. Primarily, these advancements have been focused on measurements of enteric methane, with the proliferation of GreenFeed emission measurement systems (GEM; C-Lock, Inc; Rapid City, SD) being utilized by animal scientists across the world. The GEM relies on spot measurements collected in a portable head-box, either in a freestall or on a trailer. The GEM uses bait feed to entice animals to place their head into the head-box to collect measurements. Use of respiration chambers or head-boxes are still considered the “gold standard”, but the GEM allows for quantification in production environments and with greater number of animals. While enteric emissions are the primary source of methane from ruminant agriculture, manure methane emissions account for 15.8% of direct emissions from cattle in the U.S. This emission source is a significant contributor to confined feeding operations’ greenhouse gas emissions (GHG), where consolidation and changes in manure handling practices have occurred over the last several decades. From 2010 to 2020, manure methane emissions were a larger contributor to climate warming than enteric methane (90.8 MMT CO2-we vs. 89.2 MMT CO2-we, respectively) when calculated using the new GWP* metric. However, few advancements have been made in quantifying emissions from manure, with the cost-effective static chamber methodology still widely used. This technique allows for the determination of temporal gas concentration change in a known volume of air with a PVC cylinder, inserted 5-10 cm in the soil and posteriorly closed with a PVC lid to generate “known volume” headspace. However, this method does have known limitations on spatial and temporal flux calculations. These limitations include: the PVC chamber may alter the soil microenvironment thereby altering soil GHG flux estimates; they have potential for technician bias; and are short term monitoring, limiting interpretations to that snapshot in time and making comparisons across experiments difficult. Differing measuring techniques, such as eddy covariance and dual-comb, that more accurately and precisely monitor the soil-atmosphere interface may help better understand gas fluxes from livestock systems. Key Word: cattle, enteric, manure, methane

Influential factors on the energy efficiency of fresh air systems in nearly zero energy buildings

Ensuring precise control of fresh air volume is crucial for minimizing energy usage in nearly zero energy buildings. Research shows that automatic pressure-independent dampers offer a promising solution for maintaining the desired fresh air volume. However, the energy performance of damper-controlled fresh air systems is influenced by multiple factors that have not been thoroughly investigated. This study focuses on examining the impact of influencing factors on the energy efficiency of fresh air systems. Laboratory experiments and field testing were conducted on a typical fresh air system. Subsequently, based on the experimental data, an energy saving model of the damper-controlled fresh air system was developed and validated. The main influencing factors were comprehensively investigated according to the energy-saving model. Results show that damper resistance is one of the main influencing factors on energy efficiency. Pressure-independent damper with a low resistance ratio of less than 48 % are recommended; When the average PM2.5 concentration increases by 1 µg/m3, the energy saving rate decreases by approximately 0.3 %, indicating that pressure-independent dampers are more suitable for use in regions with cleaner air; In the heating season, the energy saving rate increases by approximately 0.075 % when the dry bulb temperature decreases by 1 °C; In the cooling season, the energy saving rate increases by 1.19 % when the wet bulb temperature rises by 1 °C. This study contributes to the development of sustainable building practices by identifying key factors that influencing the energy usage of damper-controlled fresh air systems and further guiding the selection and utilization of pressure-independent dampers in nearly zero energy buildings.

Hamman syndrome with a rare feature of pneumorrhachis – an unusual complication of polysubstance abuse and e-vaping

Hamman syndrome is defined as dissection of air in mediastinum and skin fascia usually due to increased intrathoracic pressure. The air leak tends to make its way into pleural and pericardial layers; however, in rare instances air can also dissect into epidural spaces, regarded as pneumorrhachis. We present a case of a young male with a history of polysubstance abuse and e-vaping, who presented with symptoms of altered mental status. Given the concerning physical examination, a computed tomography of the chest was undertaken, which showed pneumothorax, pneumomediastinum and pneumorrhachis. The patient was closely monitored in the intensive care unit and improved after symptomatic management. The symptoms of pneumorrhachis depend on the volume and location of air in intracranial and intraspinal space. Although asymptomatic in our case, it is crucial for clinicians to be aware that pneumorrhachis with Hamman syndrome can potentially cause neurological deficits and cardiopulmonary arrest in severe cases due to increased intraspinal and intracranial hypertension, emphasising the need for close monitoring.

Tunable uniform field enhancement in a subwavelength air pillar by photonic doping in epsilon-near-zero medium

In this study, a novel electric field compressor is proposed by doping a metal-air-metal pillar in epsilon-near-zero medium within a metallic waveguide, which effectively enhances the background electric fields in a sub-wavelength air pillar with high uniformity. The field enhancement factor can be analytically determined through theoretical derivations from Maxwell’s equations, reaching its maximum value by appropriately selecting the size of the air pillar. Furthermore, the proposed compressor can achieve a tunable electric field enhancement effect within the deep sub-wavelength air pillar by adjusting the height of the air pillar through movement of two metal pillars inserted into the waveguide. Both theoretical analysis and numerical simulations are employed to validate the performance of the electric field compressor, which exhibits a wide range of tunable field enhancement effect (i.e., continuously adjustable enhancement factor between 20 and 800) with uniformity below 1.5 within the deep sub-wavelength air pillar (wherein the air volume is smaller than λ0/10 × λ0/10 × λ0/16). Finally, a practical model is proposed for the realization of the electric field compressor in the microwave range, where specially placed metal pillars and wires are incorporated into a rectangular metallic waveguide structure. The field enhancement and tunable effects of this practical model have been verified through simulations.

Review on dehumidification technology in low and extremely low humidity industrial environments

Many industrial environments have low-humidity requirements. However, most research focuses on dehumidification systems in civil buildings, while research on industrial low humidity environments is extremely limited. This paper aims to summarize the research of dehumidification systems in low-humidity industrial environments, and provide some suggestions for the selection and improvement of dehumidification systems. Firstly, the environmental control requirements of industrial plants are reviewed and categorized into low humidity and extremely low humidity based on a relative humidity of 45%. Then, the performance and applicability of condensation dehumidification systems, desiccant wheel (rotary dehumidifier) dehumidification systems and liquid desiccant dehumidification systems in typical industrial environments are summarized. Several preliminary system selection and configuration methods are presented. It is shown that the traditional condensation system is only suitable for low humidity plants. The desiccant wheel-based system is more capable of deep dehumidification, with a humidity ratio of less than 4 g/kg of supply air, while the liquid desiccant-based system can achieve high air volume operation of 10000 m3/h. Furthermore, their ranking under different scenarios is still outstanding issues. Evaluation indicators that weigh factors such as initial investment, operating costs, and control effectiveness need to be urgently proposed. Long term on-site testing is strongly recommended.

The advancing wave front on a sloping channel covered by a rod canopy following an instantaneous dam break

The drag coefficient Cd for a rigid and uniformly distributed rod canopy covering a sloping channel following the instantaneous collapse of a dam was examined using flume experiments. The measurements included space x and time t high resolution images of the water surface h(x, t) for multiple channel bed slopes So and water depths behind the dam Ho along with drag estimates provided by sequential load cells. Using these data, an analysis of the Saint-Venant equation (SVE) for the front speed was conducted using the diffusive wave approximation. An inferred Cd=0.4 from the h(x, t) data near the advancing front region, also confirmed by load cell measurements, is much reduced relative to its independently measured steady-uniform flow case. This finding suggests that drag reduction mechanisms associated with transients and flow disturbances are more likely to play a dominant role when compared to conventional sheltering or blocking effects on Cd examined in uniform flow. The increased air volume entrained into the advancing wave front region as determined from an inflow–outflow volume balance partly explains the Cd reduction from unity.

Fault detection and diagnosis in light commercial buildings’ HVAC systems: A comprehensive framework, application, and performance evaluation

The data-driven approach currently dominates the field of Automatic Fault Detection and Diagnosis (AFDD) in HVAC systems. However, a significant concern lies in the prevalent use of labeled experimental and simulation data, which often does not represent real-world operational conditions. This study unveils a comprehensive framework for AFDD in light commercial buildings, effectively leveraging unlabeled raw data extracted directly from their Building BAS. Its main goal is to provide a versatile methodology tailored for real-world applicability. Buildings classified as “light commercial” typically have less than 2,500 square meters of floor area and no more than six stories, such as small offices, medical facilities, banks, small manufacturing facilities, etc. A common feature of these buildings is the fact that the HVAC systems tend to be relatively simple and have similar configurations, thus making it easy to develop scalable and reproducible fault detection methods. The study focuses on a practical case study in a light commercial building HVAC system situated in Montreal, Canada, encompassing a single Air Handling Unit (AHU) and four Variable Air Volume (VAV) reheating boxes to evaluate the framework. This comprehensive framework encompasses a sequence of sub-objectives: creating a sizable, synchronized raw dataset from diverse BAS sensor tags, comprehensive data cleansing to address inconsistencies, developing an anomaly detection method, investigating these anomalies to extract underlying rules, and finally, dataset labeling. An AFDD classification model is then applied to evaluate its ability to distinguish normal from faulty conditions across various fault types. The study highlights the potential of dimensional reduction techniques and unsupervised clustering for effective anomaly detection in light commercial buildings, as well as the power of the Decision Tree classifier for uncovering hidden patterns, especially in anomaly conditions. It also highlights the significance of addressing imbalanced datasets in AFDD and the complexities of detecting sizing-related faults. Despite these challenges, the framework exhibits robust performance in detecting and diagnosing a range of HVAC faults. It offers a systematic and adaptable approach for handling real-world operational data in light commercial building HVAC systems, extendible to other building types, bridging the gap between data-driven methods and practical applications.

Numerical simulation and optimisation design for ventilation and heat dissipation in high-temperature and high-load indoor substations

Under high-temperature and high-load operational conditions, inadequate ventilation and suboptimal cooling arrangements within indoor substations result in high oil temperatures, posing a threat to the secure and steady operation of transformers. In this paper, the ventilation and heat dissipation effect of a 110 kV indoor substation is studied by the computational fluid dynamics method. Initially, the three-dimensional simulation model of the main transformer chamber is constructed to mirror the actual substation structure. Subsequently, the impact of the upper outlet on ventilation and heat dissipation is explored. The results show that the proximity of the upper outlet to the fan on the side wall prompts the fan to draw air from the upper outlet, diminishing the air volume entering the lower intake outlet by 38.8%. It proves detrimental to the transformer's heat dissipation efficiency. Lastly, with the upper outlet closed, the study delves into the impact of various configurations of intake and exhaust ports on optimizing ventilation and heat dissipation. A total of six cases of two scenarios for the air inlet location and three exhaust vent positions are explored. According to the simulation results, the optimal case of substation ventilation and heat dissipation is obtained by considering four evaluation parameters.

Multi-objective optimization analysis of air-cooled heat dissipation coupled with thermoelectric cooling of battery pack based on orthogonal design

As the energy supply core of electric vehicles (EVs), the battery's performance is closely related to its temperature. Therefore, the battery thermal management system (BTMS) plays a crucial role in ensuring the vehicle's driving safety and power performance. This paper proposes the air cooling as the primary heat dissipation method, combined with a semiconductor refrigeration sheet (SRS) to improve heat transfer and reduce local high temperature. Firstly, determine the optimum air volume with the U-type air-cooled structure. Additionally, orthogonal analysis is used to investigate the inlet and outlet locations, the front deflector position and length of the shunt chamber, and the rear deflector position on the air-cooling effect. Then, through multi-objective optimization, the optimal air-cooled structure is selected based on the air supply pressure drop. The chosen structure is the same-side dual-exit ventilation with a front deflector located 150 mm from the near-wind end wall and a length of 30 mm, and a rear deflector located 100 mm from the far-wind end wall. Finally, SRS coupled air cooling is used to dissipate the heat. Four SRSs are used to analyze the effect of mounting position and different currents on the battery pack. The findings suggest that the optimal placement for SRSs is parallel to the lower end of the battery module at the far-wind end. When SRSs pass a current of up to 0.4A at 37 ℃, the entire battery module can complete 7200 s discharge with 0.5C. This leads to a decrease in the maximum temperature (Tmax) to 46.09 ℃ and a drop in the temperature uniformity index (δT) to 1.36.

A novel pulse-jet cleaning method to effectively extend the lifetime of pleated filter and reduce dust emission

To solve the problem of poor cleaning effect of pleated filter, this study explored in detail the impact of various cleaning method on the filtration and cleaning performance of the filter media in clean-on-demand mode. Furthermore, the clogging mechanism of the filter and the deposition structure of dust on the filter media were analyzed based on the effective filtration area ratio and true resistance coefficient calculated by the proposed model. The results demonstrated that for the constant pulse-jet cleaning pressure (PJCP), increasing PJCP was more conducive to removing dust deposited on the filter media and improving regeneration efficiency, although higher PJCP increased power consumption. Different from the thick primary dust layer formed on the filter surface under the constant PJCP of 0.3 MPa, the dust was mainly deposited inside the filter media under the constant PJCP of 0.5 and 0.7 MPa. In contrast, stepwise increasing PJCP was more effective in cleaning and regenerating the filter media, which was reflected in further extending the filter lifetime, increasing the processing air volume and reducing the dust emission concentration with acceptable energy consumption. Moreover, the filter media mainly clogged itself and formed a medium thickness primary dust layer on the filter surface.

Experimental investigation on frosting performance of a microchannel heat exchanger in heat pump system for electric vehicles

Frosting of outdoor heat exchangers deteriorates the heat transfer performance of the electric vehicle (EV) heat pump system. This study conducted frost experiments on the outdoor heat exchanger of an EV heat pump air-conditioning system, considering different flow configurations, tube arrangements, and frontal air volume. The purpose of the study was to establish the optimal tube arrangements and flow configurations for minimizing frost formation and maximizing system performance. The results indicate that a three-flow configuration outperforms a two-flow setup under frosting conditions. Specifically, a flow sequence of 14-21-35 increases the heat capacity by 15.05 %–20.64 % compared to that of the reverse flow order of 35-21-14. The flow sequence a-b-c represents the number of flat tubes along the refrigerant flow process. Additionally, the coefficient of performance (COP) increases by 1.19 %–3.55 %. Higher airflow reduces frost formation. A significant correlation exists between the refrigerant distribution within the heat exchanger and the corresponding frost distribution on the surface of the microchannel heat exchanger. The frost formation rate was slower for the flat tube vertical arrangement. Furthermore, horizontal tube arrangements were more conductive than vertical ones, providing a more uniform temperature distribution and higher heat transfer rates (an increase of up to 2.7% in heat transfer and 3.4% in heat capacity). The COP of the vertical arrangement was consistently higher than that of the horizontal arrangement by 1.4 %–3 %.

Design of convertible patient care unit for both non-pandemic and pandemic times: Prototype, building spatial layout, and ventilation design

Convertible patient care units can accommodate non-respiratory infectious disease patients in non-pandemic times and provide isolated treatment for respiratory infectious disease patients during pandemic times. A prototype convertible patient care unit covering a floor area of 1518 m2, featuring 16 wards, and accommodating 40 beds was developed to examine the impact of building spatial layout and ventilation design on the inter-zonal airborne transmission and energy use intensity (EUI) during both non-pandemic and pandemic times. Building spatial layout referred to the presence of patient corridors and anterooms, while ventilation design referred to the location of air terminals and the calculation method of residual air volume (namely, difference between supply and exhaust airflow rates). Adding anterooms provided an 18 % reduction in pressure gradient fluctuations during door-opening events. The absence of exhaust in the medical corridor, anterooms, and wards increased contamination leakages to the patient corridors. Using the differential pressure method to calculate residual air volume was more effective in controlling the inter-zonal pressure gradient than the fixed residual air volume method. Various conversion methods resulted in an 84%–134 % increase of EUI compared to non-pandemic times, without, however, corresponding reduction in inter-zonal airborne transmission risk. The condition of adding both patient corridors and anterooms, exhaust-only patient corridors, anterooms with balanced supply-exhaust airflow rates, and differential pressure method to calculate residual air volume were effective conversion strategies to simultaneously address both the inter-zonal airborne transmission and EUI. These findings provide fundamental information for designing convertible patient care units and revising related guidelines in China.