Diameter Of Aerosol Particles Research Articles

Compact, high-flow, water-based, turbulent-mixing, condensation aerosol concentrator for collection of spot samples.

A new high-flow, compact aerosol concentrator, using rapid, turbulent mixing to grow aerosol particles into droplets for dry spot sample collection, has been designed and tested. The "TCAC (Turbulent-mixing, Condensation Aerosol Concentrator)" is composed of a saturator for generating hot vapor, a mixing section where the hot vapor mixes with the cold aerosol flow, a growth tube where condensational droplet growth primarily occurs, and a converging nozzle that focuses the droplets into a beam. The prototype concentrator utilizes an aerosol sample flow rate of 4 L min-1. The TCAC was optimized by varying the operating conditions, such as relative humidity of the aerosol flow, mixing flow ratio, vapor temperature, and impaction characteristics. The results showed that particles with a diameter ≥ 25 nm can be grown to a droplet diameter > 1400 nm with near 100% efficiency. Complete activation and growth were observed at relative humidity ≥ 25% of the aerosol sample flow. A consistent spot sample with a diameter of (the diameter of a circle containing 90% of the deposited particles) was obtained regardless of the aerosol particle diameter ( ). For fiber counting applications using phase contrast microscopy, the TCAC can reduce the sampling time, or counting uncertainty, by two to three orders of magnitude, compared to the 25-mm-filter collection. The study shows that the proposed mixing-flow scheme enables a compact spot sample collector suitable for handheld or portable applications, while still allowing for high flow rates.

Effect of forceful suction and air disinfection machines on aerosol removal

BackgroundsDental procedures involving drilling and grinding can produce a significant amount of suspended aerosol particles (PM) and bioaerosols. This study aims to analyze the size and concentration of aerosol particles generated during drilling and to investigate the effectiveness of two air exchange systems, namely forceful suction (FS) and air disinfection machines (DM), in removing PM.MethodsFor this study, 100 extracted permanent teeth were collected and divided into three groups: without suction (n = 50), suction with forceful suction (n = 25), and suction with air disinfection machines (n = 25). The removal rate of suspended aerosol particles was analyzed using particle counters and air data multimeter.ResultsWhen drilling and grinding were performed without vacuum, 0.75% of the aerosol particles generated were PM2.5-10, 78.25% of total suspended aerosol particles (TSP) were PM2.5, and 98.68% of TSP were PM1. The nanoanalyzer measurements revealed that the aerodynamic diameter of most aerosol particles was below 60 nm, with an average particle diameter of 52.61 nm and an average concentration of 2.6*1011 ultrafine aerosol particles. The air change per hour (ACH) was significantly lower in the air disinfection machines group compared to the forceful suction group. Additionally, the number of aerosol particles and mass concentration was significantly lower in the air disinfection machines group compared to the forceful suction group in terms of PM2.5 levels. However, the forceful suction group also reduced the mass concentration in PM10 level than the air disinfection machines group.ConclusionIn conclusion, the air exchange system can reduce the aerosol particles generated during drilling and grinding. Comparing the two air exchange systems, it was found that the air disinfection machines group reduces the number of aerosol particles and mass concentration in PM2.5 levels, while the forceful suction group reduces the mass concentration in PM10 level.

A new exhalation-assisted aerosol delivery method for nasal administration

Nasal administration can be used to treat not only local and systemic diseases but also central nervous system diseases. However, the delivery efficiency to the target site needs to be improved. In this paper, a new exhalation-assisted aerosol delivery method (EDM) for nasal administration is proposed. Numerical simulation model validated by experiments was applied to investigate the transport phenomenon of aerosol drugs in the nasal cavity. The effects of aerosol particle diameter and expiratory flow rate on delivery efficiency were investigated. The results show that exhalation flow prevents small-sized particles from entering the larynx and lower respiratory tract, so it will reduce drug wastage and side effects. Moreover, the delivery efficiency of EDM was compared with bi-direction nasal delivery method (BDM) to confirm that the proposed method has an advantage. A slight exhalation flow during aerosol administration can achieve higher delivery efficiency to the turbinate compared with BDM for small particles. There exists an optimum expiratory flow rate for a specific particle size that maximizes the delivery efficiency of the turbinate. The EDM has the advantages of more uniform drug distribution and higher delivery efficiency, it may be more promising for the treatment of central nervous system diseases, local diseases, and systemic diseases in the future.

Efficient, Breathable, and Compostable Multilayer Air Filter Material Prepared from Plant-Derived Biopolymers.

State-of-art face masks and respirators are fabricated as single-use devices using microfibrous polypropylene fabrics, which are challenging to be collected and recycled at a community scale. Compostable face masks and respirators can offer a viable alternative to reducing their environmental impact. In this work, we have developed a compostable air filter produced by electrospinning a plant-derived protein, zein, on a craft paper-based substrate. The electrospun material is tailored to be humidity tolerant and mechanically durable by crosslinking zein with citric acid. The electrospun material demonstrated a high particle filtration efficiency (PFE) of 91.15% and a high pressure drop (PD) of 191.2 Pa using an aerosol particle diameter of 75 ± 2 nm at a face velocity of 10 cm/s. We deployed a pleated structure to reduce the PD or improve the breathability of the electrospun material without compromising the PFE over short- and long-duration tests. Over a 1 h salt loading test, the PD of a single-layer pleated filter increased from 28.9 to 39.1 Pa, while that of the flat sample increased from 169.3 to 327 Pa. The stacking of pleated layers enhanced the PFE while retaining a low PD; a two-layer stack with a pleat width of 5 mm offers a PFE of 95.4 ± 0.34% and a low PD of 75.2 ± 6.1 Pa.

Size distribution and relationship of airborne SARS-CoV-2 RNA to indoor aerosol in hospital ward environments

Aerosol particles proved to play a key role in airborne transmission of SARS-CoV-2 viruses. Therefore, their size-fractionated collection and analysis is invaluable. However, aerosol sampling in COVID departments is not straightforward, especially in the sub-500-nm size range. In this study, particle number concentrations were measured with high temporal resolution using an optical particle counter, and several 8 h daytime sample sets were collected simultaneously on gelatin filters with cascade impactors in two different hospital wards during both alpha and delta variants of concern periods. Due to the large number (152) of size-fractionated samples, SARS-CoV-2 RNA copies could be statistically analyzed over a wide range of aerosol particle diameters (70–10 µm). Our results revealed that SARS-CoV-2 RNA is most likely to exist in particles with 0.5–4 µm aerodynamic diameter, but also in ultrafine particles. Correlation analysis of particulate matter (PM) and RNA copies highlighted the importance of indoor medical activity. It was found that the daily maximum increment of PM mass concentration correlated the most with the number concentration of SARS-CoV-2 RNA in the corresponding size fractions. Our results suggest that particle resuspension from surrounding surfaces is an important source of SARS-CoV-2 RNA present in the air of hospital rooms.

Comparative Dissemination of Aerosol and Splatter Using Suction Device during Ultrasonic Scaling: A Pilot Study.

Objective: This study compared the aerosol and splatter diameter and count numbers produced by a dental mouth prop with a suction holder device and a saliva ejector during ultrasonic scaling in a clinical setting. Methodology: Fluorescein dye was placed in the dental equipment irrigation reservoirs with a mannequin, and an ultrasonic scaler was employed. The procedures were performed three times per device. The upper and bottom board papers were placed on the laboratory platform. All processes used an ultrasonic scaler to generate aerosol and splatter. A dental mouth prop with a suction holder and a saliva ejector were also tested. Photographic analysis was used to examine the fluorescein samples, followed by image processing in Python and assessment of the diameter and count number. For device comparison, statistics were used with an independent t-test. Result: When using the dental mouth prop with a suction holder, the scaler produced aerosol particles that were maintained on the upper board paper (mean ± SD: 1080 ± 662 µm) compared to on the bottom board paper (1230 ± 1020 µm). When the saliva ejector was used, it was found that the diameter of the aerosol on the upper board paper was 900 ± 580 µm, and the diameter on the bottom board paper was 1000 ± 756 µm. Conclusion: There was a significant difference in the aerosol and splatter particle diameter and count number between the dental mouth prop with a suction holder and saliva ejector (p < 0.05). Furthermore, the results revealed that there was a statistically significant difference between the two groups on the upper and bottom board papers.

Experimental Evaluation of Dry Powder Inhalers during Inhalation and Exhalation Using a Model of the Human Respiratory System (xPULM™).

Dry powder inhalers are used by a large number of patients worldwide to treat respiratory diseases. The objective of this work is to experimentally investigate changes in aerosol particle diameter and particle number concentration of pharmaceutical aerosols generated by four dry powder inhalers under realistic inhalation and exhalation conditions. To simulate patients undergoing inhalation therapy, the active respiratory system model (xPULM™) was used. A mechanical upper airway model was developed, manufactured, and introduced as a part of the xPULM™ to represent the human upper respiratory tract with high fidelity. Integration of optical aerosol spectrometry technique into the setup allowed for evaluation of pharmaceutical aerosols. The results show that there is a significant difference (p < 0.05) in mean particle diameter between inhaled and exhaled particles with the majority of the particles depositing in the lung, while particles with the size of (>0.5 μm) are least influenced by deposition mechanisms. The fraction of exhaled particles ranges from 2.13% (HandiHaler®) over 2.94% (BreezHaler®), and 6.22% (Turbohaler®) to 10.24% (Ellipta®). These values are comparable to previously published studies. Furthermore, the mechanical upper airway model increases the resistance of the overall system and acts as a filter for larger particles (>3 μm). In conclusion, the xPULM™ active respiratory system model is a viable option for studying interactions of pharmaceutical aerosols and the respiratory tract regarding applicable deposition mechanisms. The model strives to support the reduction of animal experimentation in aerosol research and provides an alternative to experiments with human subjects.

Aerosol Electroanalysis by PILSNER: Particle-into-Liquid Sampling for Nanoliter Electrochemical Reactions.

Particle-into-liquid sampling (PILS) has enabled robust quantification of analytes of interest in aerosol particles. In PILS, the limit of detection is limited by the factor of particle dilution into the liquid sampling volume. Thus, much lower limits of detection can be achieved by decreasing the sampling volume and increasing the surface area-to-volume ratio of the collection substrate. Unfortunately, few analytical techniques can realize this miniaturization. Here, we use an ultramicroelectrode in a microliter or smaller sampling volume to detect redox active species in aerosols to develop the technique of Particle-into-Liquid Sampling for Nanoliter Electrochemical Reactions (PILSNER). As a proof-of-concept to validate this technique, we demonstrate the detection of K4Fe(CN)6 in aerosol particles (diameter ∼0.1-2 μm) and quantify the electrochemical response. To further explore the utility of the method to detect environmentally relevant redox molecules, we show PILSNER can detect 1 ng/m3 airborne Pb in aerosols. We also demonstrate the feasibility of detecting perfluorooctanesulfonate (PFOS), a persistent environmental contaminant, using this technique. PILSNER is shown to represent a significant advancement toward simple and effective detection of a variety of emerging contaminants with an easily miniaturizable and tunable electroanalytical platform.

The Asian tropopause aerosol layer within the 2017 monsoon anticyclone: microphysical properties derived from aircraft-borne in situ measurements

Abstract. The Asian summer monsoon is an effective pathway for aerosol particles and precursors from the planetary boundary layer over Central, South, and East Asia into the upper troposphere and lower stratosphere. An enhancement of aerosol particles within the Asian monsoon anticyclone (AMA), called the Asian tropopause aerosol layer (ATAL), has been observed by satellites. We discuss airborne in situ and remote sensing observations of aerosol microphysical properties conducted during the 2017 StratoClim field campaign within the AMA region. The aerosol particle measurements aboard the high-altitude research aircraft M55 Geophysica (maximum altitude reached of ∼20.5 km) were conducted with a modified ultra-high-sensitivity aerosol spectrometer – airborne (UHSAS-A; particle diameter detection range of 65 nm to 1 µm), the COndensation PArticle counting System (COPAS, detecting total concentrations of submicrometer-sized particles), and the New Ice eXpEriment – Cloud and Aerosol Spectrometer with Detection of POLarization (NIXE-CAS-DPOL). In the COPAS and UHSAS-A vertical particle mixing ratio (PMR) profiles and the size distribution profiles (for number, surface area, and volume concentration), the ATAL is evident as a distinct layer between ∼370 and 420 K potential temperature (Θ). Within the ATAL, the maximum detected PMRs (from the median profiles) were ∼700 mg−1 for particle diameters between 65 nm and 1 µm (UHSAS-A) and higher than 2500 mg−1 for diameters larger than 10 nm (COPAS). These values are up to 2 times higher than those previously found at similar altitudes in other tropical locations. The difference between the PMR profiles measured by the UHSAS-A and the COPAS indicate that the region below the ATAL at Θ levels from 350 to 370 K is influenced by the nucleation of aerosol particles (diameter &lt;65 nm). We provide detailed analyses of the vertical distribution of the aerosol particle size distributions and the PMR and compare these with previous tropical and extratropical measurements. The backscatter ratio (BR) was calculated based on the aerosol particle size distributions measured in situ. The resulting data set was compared with the vertical profiles of the BR detected by the multiwavelength aerosol scatterometer (MAS) and an airborne miniature aerosol lidar (MAL) aboard the M55 Geophysica and by the satellite-borne Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP). The data of all four methods largely agree with one another, showing enhanced BR values in the altitude range of the ATAL (between ∼15 and 18.5 km) with a maximum at 17.5 km altitude. By means of the AMA-centered equivalent latitude calculated from meteorological reanalysis data, it is shown that such enhanced values of the BR larger than 1.1 could only be observed within the confinement of the AMA.

A method for estimating the ratio of aerosol mass concentration to the imaginary part of the atmospheric complex refractive index and its application

Based on the principle of light propagation, it is necessary to obtain the ratio (RMN) of atmospheric aerosol mass concentration to the imaginary part of the atmospheric equivalent refractive index for measuring aerosol mass vertical flux. In this paper, the factors affecting the RMN values are analyzed by numerical calculation under an ideal state and by using observational data. Numerical calculations show that the RMN is mainly determined by the aerosol particle size distribution (PSD), hygroscopicity parameters and relative humidity. With the same relative humidity, the smaller the geometric mean diameter (Dg) is, the larger the RMN, and when the aerosol particle hygroscopicity parameter is greater than 0.14, the greater the relative humidity is, the smaller the RMN. Comprehensive experiments were conducted in urban Hefei, and the results of observations at Hefei confirm the numerical results. Data from ten cities across China also confirm the numerical results. The order of geometric mean diameter of aerosol particles at the ten sites can be determined by the order of RMN, and the order of hygroscopicity parameters at the ten sites can be determined by the order of the change rate of RMN with relative humidity. The geometric mean diameters of aerosol particles are different among the ten sites, while the hygroscopicity parameters are similar.

Study on Gravity Sedimentation of Multicomponent Hygroscopic Aerosols in Reactor Severe Accident

In the event of a severe accident, the multicomponent hygroscopic aerosols in the containment will absorb water under the high humidity condition, thereby influencing the gravity sedimentation behavior. In this study, a physical model of the equilibrium particle diameter of the multicomponent hygroscopic aerosol particles was developed through theoretical analysis, and it was also validated by experimental results. The model focuses on the effect of solubility on the hygroscopic process and explains the reason why the multicomponent hygroscopic particles grow along a discontinuity curve. Based on a typical gigawatt-class pressurized water reactor, the effects of relative humidity, dry particle diameter and mass fraction of hygroscopic components on the removal coefficient of the gravity sedimentation were investigated. The results show that the velocity of the gravity sedimentation will significantly increase, only if the aerosol particles grow to a certain degree. Only when the humidity is more than a certain value, the sedimentation process of the pure hygroscopic aerosol particles with a dry particle diameter exceeding 0.1 μm will accelerate due to hygroscopicity, and this humidity limit will decrease as the dry particle diameter increases. With the progress of the accident, the mass fraction of non-hygroscopic components in the aerosol particles gradually decreases, leading the above-mentioned humidity limit increasing and the acceleration of gravity sedimentation due to the hygroscopicity decreasing in the same humidity.

Seasonal variability and trends in global type-segregated aerosol optical depth as revealed by MISR satellite observations

This study utilized a long-term (2001–2018) aerosol optical component dataset retrieved from the Multiangle Imaging Spectroradiometer (MISR), Version 23, to perform comprehensive analyses of the global climatology of seasonal AODs, partitioned by aerosol types (including small-size, medium-size, large-size, spherical, and non-spherical). By dividing eight different AOD bins and performing trend analysis, the seasonal variability and trends in these type-segregated AODs, as well as in the frequency occurrences (FOs) for different AOD bins, globally and over 12 regions of interest, were also investigated. In terms of particle size, small-size aerosol particles (diameter < 0.7 μm) contribute the largest to global extinction in all three seasons except winter. A similar globally dominant role is exhibited by spherical aerosols, which contribute 68.5%, 73.3%, 71.6% and 70.2% to the global total AOD (TAOD) in spring, summer, autumn and winter, respectively, on a global average scale. FOs with different aerosol loading levels suggested that the seasonal FOs tend to decrease progressively with increasing aerosol loading, except for Level 1 (TAOD< 0.05). Examination of the seasonal distribution of FOs revealed that the FO at Level 1 (Level 2, 0.05 < TAOD< 0.15) is much larger in summer/winter (winter/autumn) than in spring/autumn (spring/summer) over most areas of the world. However, the FOs for Level 3 (0.15 < TAOD< 0.25) to Level 8 (TAOD> 1.0) generally exhibit greater intensity in spring/summer than in autumn/winter. Temporal trend analyses showed that the seasonal TAOD experiences a significant decline during 2001–2018 in most regions globally, except in South Asia, the Middle East, and North Africa. Opposite seasonal trends in the above regions are closely related to the increase in FOs in the range of 0.4 < TAOD< 1.0. The global average TAOD shows the most pronounced decline in spring, falling by −10.4% (P < 0.05). Examination of the trends in type-segregated AODs further revealed that the decreases in size-segregated (shape-segregated) AODs all contribute to the decrease in seasonal TAOD, with small-size AOD (spherical AOD) contributing most significantly.

Aerosol deposition and airflow dynamics in healthy and asthmatic human airways during inhalation

Inhalation of aerosols such as pharmaceutical aerosols or virus aerosol uptake is of great concern to the human population. To elucidate the underlying aerosol dynamics, the deposition fractions (DFs) of aerosols in healthy and asthmatic human airways of generations 13–15 are predicted. The Navier-stokes equations governing the gaseous phase and the discrete phase model for particles’ motion are solved using numerical methods. The main forces responsible for deposition are inertial impaction forces and complex secondary flow velocities. The curvatures and sinusoidal folds in the asthmatic geometry lead to the formation of complex secondary flows and hence higher DFs. The intensities of complex secondary flows are strongest at the generations affected by asthma. The DF in the healthy airways is 0%, and it ranges from 1.69% to 52.93% in the asthmatic ones. From this study, the effects of the pharmaceutical aerosol particle diameters in the treatment of asthma patients can be established, which is conducive to inhibiting the inflammation of asthma airways. Furthermore, with the recent development of COVID-19 which causes pneumonia, the predicted physics and effective simulation methods of bioaerosols delivery to asthma patients are vital to prevent the exacerbation of the chronic ailment and the epidemic.

Inhalation of IL-1 Receptor Antagonist (ALTA-2530) Achieves Stable and Prolonged Pulmonary Exposure in Nonclinical Studies Supportive of Development for Bronchiolitis Obliterans Syndrome

Purpose ALTA-2530 is a novel inhaled formulation of recombinant human IL-1 receptor antagonist (rhIL-1Ra) in development for bronchiolitis obliterans syndrome (BOS). IL-1 overexpression in BOS drives chronic inflammation and fibroblast activation leading to airway remodeling and impaired oxygen transfer. Endogenous IL-1Ra is upregulated in response to IL-1 to limit cytokine signaling, but expression is inadequate to prevent BOS. Pharmacological IL-1 blockade is considered akin to restoration of physiologic immune regulation. Herein we determine if ALTA-2530 is stable during nebulization, achieves aerosol particle diameters consistent with distribution to distal airways, and pulmonary exposure commensurate with treatment of BOS. Methods Aerosolization and in vivo studies were performed with Aerogen Solo or Phillips InnospireGo vibrating mesh nebulizers. Rats (n=4/grp/timepoint) received ALTA-2530 by nose-only inhalation (0.63, 1.3, and 2.1mg/g lung). Serum and bronchioalveolar lavage (BAL) samples were collected for analysis by LC-MSMS. ALTA-2530 in lung epithelial lining fluid (ELF) was calculated using a BALF dilution factor. Results Nebulized ALTA-2530 delivered rhIL-1Ra particles with mass median aerodynamic diameters of ∼2.5-4 µm, consistent with delivery to small bronchioles. Impurity profiling by HPLC-UV and HPLC-SEC methods and an in vitro potency assay demonstrated rhIL-1Ra protein was stable during nebulization and retained full potency. ALTA-2530 achieved extensive and sustained exposure in lung ELF. The ratio of ELF to serum rhIL-1Ra was >2500X across all doses compared to 0.44X reported for lung tissue to plasma following a 5 hr IV infusion. Duration of lung exposure from a single inhaled dose exceeded 24 hr, in contrast to 1000X. Conclusion Nebulized ALTA-2530 delivers stable and active rhIL-1Ra protein, in a particle size for delivery to small airways of the lung and exposure duration predictive for once daily therapeutic dosing in BOS.

Numerical Simulation of the Aerosol Particle Motion in Granular Filters with Solid and Porous Granules

In this work, a study was carried out to compare the filtering and hydrodynamic properties of granular filters with solid spherical granules and spherical granules with modifications in the form of micropores. We used the discrete element method (DEM) to construct the geometry of the filters. Models of granular filters with spherical granules with diameters of 3, 4, and 5 mm, and with porosity values of 0.439, 0.466, and 0.477, respectively, were created. The results of the numerical simulation are in good agreement with the experimental data of other authors. We created models of granular filters containing micropores with different porosity values (0.158–0.366) in order to study the micropores’ effect on the aerosol motion. The study showed that micropores contribute to a decrease in hydrodynamic resistance and an increase in particle deposition efficiency. There is also a maximum limiting value of the granule microporosity for a given aerosol particle diameter when a further increase in microporosity leads to a decrease in the deposition efficiency.

Insights into the chemistry of aerosol growth in Beijing: Implication of fine particle episode formation during wintertime

Nucleation particle growth plays a major role in the occurrence of fine particles, yet the mechanism of new particle formation (NPF) remains ambiguous in the complex atmosphere of megacities and hinders the development of measures to mitigate PM2.5 pollution. In this study, the chemistry of ultrafine particles during the growth phase of nucleation events was investigated in urban Beijing from Nov. 15, 2018 to Jan. 15, 2019, using two scanning mobility particle spectrometers (SMPS) systems and an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS). During this intense campaign, 11 NPF events were observed and the growth rate (GR) of nanoparticles ranged from 12.5 to 24.5 nm h−1. Four periodic cycles of PM2.5 episodes that included aerosol particle growth to particulate matter pollution were identified. Based on the QGR – QAMS theoretical frame that exploring the balance between the source rate of condensable vapors and the observed growth rate of nanoparticles, we clearly showed the physical and chemical evolution of nano-particle during the growth processes to ambient-atmosphere sizes (>100 nm). Generally, the modal diameter of aerosol particles grew by more than 100 nm (7 out of 11 NPF events) when the nitrate concentration and less-oxidized oxygenated organic aerosol (LO-OOA) were high; however, another class of aerosol particle growth was limited to 50–100 nm (3 out of 11 NPF events) when sulfate was high. Note that the remaining one NPF event could not be identified if it can grow up to 100 nm or not due to the unavailable of observation data during the late growth stage. By linking the aerosol growth with chemical compositions, sulfate and organics were found to be the main contributors during the initial stage of the aerosol growth, while cooking-related OA (COA) enhanced the transition stage, and nitrate and more-oxidized OOA (MO-OOA) dominated the subsequent growth of aerosol to ambient-atmosphere sizes. An important portion of aerosol growth in PM2.5 was controlled by semi-volatile organic vapors, which can partition into the externally condensed phase of the accumulation mode and coarse mode via the physical process of adsorption. Through quantifying the physical and chemical properties of aerosol particle growth, the detail processes of nucleation initiated PM2.5 pollution episodes were evaluated and provided observational evidence on the formation mechanism of winter haze pollution in the megacity of Beijing.

Experimental Study on the Dependency of Ice Nucleation Active Surface Site Density on ATD Aerosol Size

In light of the percentage of Earth’s cloud coverage, heterogeneous ice nucleation in clouds is the most important global-scale pathway. More recent parameterizations of ice nucleation processes in the atmosphere are based on the concept of ice nucleation active surface site density (ns). It is usually assumed that ns is independent of time and aerosol size distribution, i.e. that the surface properties of aerosols of the same species do not vary with size. However, the independence of ns on aerosol size for every species has been questioned. This study presents the results of ice nucleation processes of ATD laboratory-generated aerosol (particle diameters of 0 - 3 μm). Ice nucleation in the condensation mode was performed in a Dynamic Filter Processing Cham- ber at temperatures of -18°C and -22°C, with a saturation ratio with respect to water of 1.02. Results show that ns increased by lowering the nucleation temperature, and was also dependent on the particle size. The ns of particles collected on the filters, after a 0.5 μm D50 cut-off cyclone, resulted statistically higher with respect to the values obtained from the particles collected on total filters. The results obtained suggest the need for further investigation of ns dependence of same composition aerosol particles with a view to support weather and climate predictions.

Capturing Aerosol Particles in a Device with a Regular Pulsating Nozzle

The paper is dedicated to reducing the technogenic impact on the environment of using highly efficient apparatus for the complex exhaust gas treatment, operating in the advanced turbulence regime – an apparatus with a regular pulsating nozzle (RPN). Devices with on-load tap-changers are characterized by high efficiency of capturing solid particles of different dispersion (e.g., fog, dust, and smoke), the possibility of self-cleaning of contact elements from sticky dust, low material consumption, and high reliability in operation. Purpose of the study – to obtain analytical solutions for assessing the efficiency of capturing polydisperse aerosols in an apparatus with an on-load tap-changer due to diffusion and inertial mechanisms. The paper proposes a new solution for the minimum effective diameter of aerosol particles that can be captured in devices with an on-load tap-changer and can be used for a wide range of diameters of absorbing liquid droplets and their number in the volume of the apparatus. The calculations allow us to say that the minimum effective diameter of aerosol particles captured by liquid drops in an apparatus with an on-load tap-changer is less than 0.3 microns.

Thermodynamic equilibrium dose-response models for MERS-CoV infection reveal a potential protective role of human lung mucus but not for SARS-CoV-2

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) and Middle East respiratory syndrome coronavirus (MERS-CoV) infect the human respiratory tract. A prototype thermodynamic equilibrium model is presented here for the probability of the virions getting through the mucus barrier and infecting epithelial cells based on the binding affinity (Kmucin) of the virions to mucin molecules in the mucus and parameters for binding and infection of the epithelial cell. Both MERS-CoV and SARS-CoV-2 bind strongly to their cellular receptors, DDP4 and ACE2, respectively, and infect very efficiently both bronchus and lung ex vivo cell cultures which are not protected by a mucus barrier. According to the model, mucin binding could reduce the infectivity for MERS-CoV compared to SARS-CoV-2 by at least 100-fold depending on the magnitude of Kmucin. Specifically Kmucin values up to 106 M−1 have little protective effect and thus the mucus barrier would not remove SARS-CoV-2 which does not bind to sialic acids (SA) and hence would have a very low Kmucin. Depending on the viability of individual virions, the ID50 for SARS-CoV-2 is estimated to be ~500 virions (viral RNA genomic copies) representing 1 to 2 pfu. In contrast MERS-CoV binds both SA and human mucin and a Kmucin of 5 × 109 M−1 as reported for lectins would mop up 99.83% of the virus according to the model with the ID50 for MERS-CoV estimated to be ~295,000 virions (viral RNA genomic copies) representing 819 pfu. This could in part explain why MERS-CoV is poorly transmitted from human to human compared to SARS-CoV-2. Some coronaviruses use an esterase to escape the mucin, although MERS-CoV does not. Instead, it is shown here that “clustering” of virions into single aerosol particles as recently reported for rotavirus in extracellular vesicles could provide a co-operative mechanism whereby MERS-CoV could theoretically overcome the mucin barrier locally and a small proportion of 10 μm diameter aerosol particles could contain ~70 virions based on reported maximum levels in saliva. Although recent evidence suggests SARS-CoV-2 initiates infection in the nasal epithelium, the thermodynamic equilibrium models presented here could complement published approaches for modelling the physical entry of pathogens to the lung based on the fate and transport of the pathogen particles (as for anthrax spores) to develop a dose-response model for aerosol exposure to respiratory viruses. This would enable the infectivity through aerosols to be defined based on molecular parameters as well as physical parameters. The role of the spike proteins of MERS-CoV and SARS-CoV-2 binding to SA and heparan sulphate, respectively, may be to aid non-specific attachment to the host cell. It is proposed that a high Kmucin is the cost for subsequent binding of MERS-CoV to SAs on the cell surface to partially overcome the unfavourable entropy of immobilisation as the virus adopts the correct orientation for spike protein interactions with its protein cellular receptor DPP4.

The importance of representative aerosol diameter and bubble size distribution in pool scrubbing

Mitigation methods that reduce the amount of radioactive materials leaking into the environment have emerged as a critical issue. Many researchers have found that pool scrubbing can play a crucial role in this process. Pool scrubbing is a practice that removes radioactive aerosols using pool water when a gas containing aerosols rises in a pool. Several codes have been developed to evaluate how much aerosol is removed during the pool scrubbing process. This study aims to improve the pool scrubbing code in a bubbly flow to make it more realistic. The importance of selecting a representative diameter of aerosol particles with a lognormal distribution is discussed. Moreover, unlike the BUSCA (BUbble SCrubbing Algorithm) code and the SPARC (Suppression Pool Aerosol Removal Code) code, which do not account for the condensation effect of the steam in the injection region or for thermophoresis, respectively, the presented code, called POSCAR (POol SCrubbing Aerosol Removal code), takes these two phenomena into account. Additionally, the calculation is performed considering the aerosol removal effect with the lognormal bubble size distribution, which had not been considered in the two aforementioned codes. Finally, the performance of this code is evaluated based on experimental results to further improve existing codes.