Aerosol Dispersion Performance Research Articles

Preparation and characterization of lysozyme loaded liposomal dry powder inhalation using non-ionic surfactants

Delivering protein drugs through dry powder inhalation (DPI) remains a significant challenge. Liposomes offer a promising solution, providing protection for proteins from external environment and controlled release capabilities. Furthermore, the use of non-ionic surfactants plays a crucial role in protecting the activity of proteins because of how the surfactants positioning themselves at the liquid–gas interface during the spray-drying process. In this study, lysozyme-loaded liposomal DPI formulations were prepared using various non-ionic surfactants, including polysorbate 80, poloxamer 188, poloxamer 407, and sucrose stearate. Lysozyme solution and 1,2-distearoyl-sn-glycero-3-phosphatidylcholine liposomes were subjected through high-pressure homogenization to form lysozyme-loaded liposomes. Formulations of homogenized lysozyme liposomes were spray-dried and further characterized. The particle size of reconstituted liposomal lysozyme DPI was from 129.5 to 816.9 nm. The formulations showed encapsulation efficiency up to 32.5% with zeta potential value of around − 30 mV, and spherical structures were observed. The aerosol dispersion performance of the dry powder inhalers was evaluated with emitted doses reaching up to 103% and fine particle fractions up to 28.4%. Significantly higher lysozyme activity was confirmed in formulation with drug to PS 80 ratio of 1: 0.5 w/w (92.1%) compared to that of formulation containing no surfactant (59.8%). The formulation stood out as the only formulation that maintained protein activity while demonstrating good aerosol performance.

Investigation of aerosol dispersion and air purifier performance in a hospital patient room using CFD and measurements

Transmission of airborne disease is a concern in many indoor spaces. Recent studies have identified correlations between poor indoor air quality (IAQ) and COVID-19 vulnerability and mortality. Studying the role building design and ventilation play in both the spread and mitigation of airborne viruses in high-density spaces is thus imperative. However, guidance for IAQ improvement and COVID-19 risk mitigation is general and insufficient for specific application in at-risk spaces like British Columbia’s (BC) patient settings and long-term care homes. What remains underdefined is a workflow for translating site specific data on indoor aerosol spread into actionable tools health officials can use towards building retrofit and intervention planning. The objective of this project was thus to develop a library of ‘digital twin’ models of at-risk indoor spaces that can provide accurate and rapid investigations of indoor air quality improvement measures using computation fluid dynamics (CFD) software. To calibrate these models, 41 repeated controlled experiments of aerosol dispersion and removal were conducted to assess the ventilation patterns of a 4-bed hospital room. From these experiments, a 3D CFD model of the room was created using the RhinoCFD modelling package, calibrated with measured IAQ sensor data, and validated against the results of the live study. This paper presents the methodology and in-progress results of this CFD modelling process.

A facile one-step jet-milling approach for the preparation of proliposomal dry powder for inhalation as effective delivery system for anti-TB therapeutics

Objective Physicochemical characterization and assessment of aerosol dispersion performance of anti-TB proliposome dry powders for inhalation (DPIs) prepared using a single-step jet-milling (JM) approach. Significance Conventional tuberculosis (TB) treatment involves isoniazid and rifampicin as first-line agents in extended oral multi-drug regimes. Liposomal DPIs are emerging as promising alternatives for targeted delivery of anti-TB agents to alveolar macrophages harboring Mycobacterium tuberculosis. However, traditional approaches for liposomal DPI preparation are tedious, time consuming and require sophisticated/expensive equipment. The proposed JM technique for preparation of proliposome DPIs could obviate these limitations and facilitate use of these drugs for more effective and safer treatment. Methods Proliposome DPIs containing isoniazid and/or rifampicin, cholesterol and cholesterol sulfate were successfully prepared via JM (injection pressure, 7.4 bar; milling pressure, 3.68 bar). Their physicochemical, content uniformity, and in vitro aerosol dispersion performance were assessed using scanning electron microscopy/energy-dispersive X-ray spectroscopy, transmission electron microscopy, dynamic light scattering/Zeta potential, X-ray diffraction spectroscopy, thermogravimetric analysis, high-performance liquid chromatography, and the Next-Generation Impactor. Results The DPIs exhibited consistent, spherically shaped, smooth particles. Drug particles were evenly distributed with acceptable content uniformity. Drug crystallinity was not significantly affected by milling and the formulations had minimal (<2.0%) water content. After reconstitution of the DPIs, the hydrodynamic size was about 370.9–556.2 nm and charge was –12.3 to –47.3 mV. Furthermore, the proliposome DPIs presented emitted dose (69.04–89.03%), fine particle fraction, <4.4 µm (13.7 − 57.8%), and mass median aerodynamic diameter (<3.0 µm), which satisfied the requirements for deep lung delivery. Conclusion The proposed approach was suitable for preparation of proliposome DPIs that could be deployed for local targeting of the lower respiratory tract for the treatment of TB.

Advanced Microparticulate/Nanoparticulate Respirable Dry Powders of a Selective RhoA/Rho Kinase (Rock) Inhibitor for Targeted Pulmonary Inhalation Aerosol Delivery.

Pulmonary hypertension (PH) is a progressive disease that eventually leads to heart failure and potentially death for some patients. There are many unique advantages to treating pulmonary diseases directly and non-invasively by inhalation aerosols and dry powder inhalers (DPIs) possess additional unique advantages. There continues to be significant unmet medical needs in the effective treatment of PH that target the underlying mechanisms. To date, there is no FDA-approved DPI indicated for the treatment of PH. Fasudil is a novel RhoA/Rho kinase (ROCK) inhibitor that has shown great potential in effectively treating pulmonary hypertension. This systematic study is the first to report on the design and development of DPI formulations comprised of respirable nanoparticles/microparticles using particle engineering design by advanced spray drying. In addition, comprehensive physicochemical characterization, in vitro aerosol aerosol dispersion performance with different types of human DPI devices, in vitro cell-drug dose response cell viability of different human respiratory cells from distinct lung regions, and in vitro transepithelial electrical resistance (TEER) as air-interface culture (AIC) demonstrated that these innovative DPI fasudil formulations are safe on human lung cells and have high aerosol dispersion performance properties.

Synthesis, Physicochemical Characterization, In Vitro 2D/3D Human Cell Culture, and In Vitro Aerosol Dispersion Performance of Advanced Spray Dried and Co-Spray Dried Angiotensin (1-7) Peptide and PNA5 with Trehalose as Microparticles/Nanoparticles for Targeted Respiratory Delivery as Dry Powder Inhalers.

The peptide hormone Angiotensin (1—7), Ang (1—7) or (Asp-Arg-Val-Tyr-Ile-His-Pro), is an essential component of the renin–angiotensin system (RAS) peripherally and is an agonist of the Mas receptor centrally. Activation of this receptor in the CNS stimulates various biological activities that make the Ang (1—7)/MAS axis a novel therapeutic approach for the treatment of many diseases. The related O-linked glycopeptide, Asp-Arg-Val-Tyr-Ile-His-Ser-(O-β-D-Glc)-amide (PNA5), is a biousian revision of the native peptide hormone Ang (1—7) and shows enhanced stability in vivo and greater levels of brain penetration. We have synthesized the native Ang (1—7) peptide and the glycopeptide, PNA5, and have formulated them for targeted respiratory delivery as inhalable dry powders. Solid phase peptide synthesis (SPPS) successfully produced Ang (1—7) and PNA5. Measurements of solubility and lipophilicity of raw Ang (1—7) and raw PNA5 using experimental and computational approaches confirmed that both the peptide and glycopeptide have high-water solubility and are amphipathic. Advanced organic solution spray drying was used to engineer the particles and produce spray-dried powders (SD) of both the peptide and the glycopeptide, as well as co-spray-dried powders (co-SD) with the non-reducing sugar and pharmaceutical excipient, trehalose. The native peptide, glycopeptide, SD, and co-SD powders were comprehensively characterized, and exhibited distinct glass transitions (Tg) consistent with the amorphous glassy state formation with Tgs that are compatible with use in vivo. The homogeneous particles displayed small sizes in the nanometer size range and low residual water content in the solid-state. Excellent aerosol dispersion performance with a human DPI device was demonstrated. In vitro human cell viability assays showed that Ang (1—7) and PNA5 are biocompatible and safe for different human respiratory and brain cells.

Design and Comprehensive Characterization of Tetramethylpyrazine (TMP) for Targeted Lung Delivery as Inhalation Aerosols in Pulmonary Hypertension (PH): In Vitro Human Lung Cell Culture and In Vivo Efficacy.

This is the first study reporting on the design and development innovative inhaled formulations of the novel natural product antioxidant therapeutic, tetramethylpyrazine (TMP), also known as ligustrazine. TMP is obtained from Chinese herbs belonging to the class of Ligusticum. It is known to have antioxidant properties. It can act as a Nrf2/ARE activator and a Rho/ROCK inhibitor. The present study reports for the first time on the comprehensive characterization of raw TMP (non-spray dried) and spray dried TMP in a systematic manner using thermal analysis, electron microscopy, optical microscopy, and Raman spectroscopy. The in vitro aerosol dispersion performance of spray dried TMP was tested using three different FDA-approved unit-dose capsule-based human dry powder inhaler devices. In vitro human cellular studies were conducted on pulmonary cells from different regions of the human lung to examine the biocompatibility and non-cytotoxicity of TMP. Furthermore, the efficacy of inhaled TMP as both liquid and dry powder inhalation aerosols was tested in vivo using the monocrotaline (MCT)-induced PH rat model.

Organic Solution Advanced Spray-Dried Microparticulate/Nanoparticulate Dry Powders of Lactomorphin for Respiratory Delivery: Physicochemical Characterization, In Vitro Aerosol Dispersion, and Cellular Studies.

The purpose of this study was to formulate Lactomorphin (MMP2200) in its pure state as spray-dried(SD) powders, and with the excipient Trehalose as co-spray-dried(co-SD) powders; for intranasal and deep lung administration with Dry Powder Inhalers (DPI). Lactomorphin is a glycopeptide which was developed for the control of moderate to severe pain. Particles were rationally designed and produced by advanced spray drying particle engineering in a closed mode from a dilute organic solution. Comprehensive physicochemical characterization using different analytical techniques was carried out to analyze the particle size, particle morphology, particle surface morphology, solid-state transitions, crystallinity/non-crystallinity, and residual water content. The particle chemical composition was confirmed using attenuated total reflectance-Fourier-transform infrared (ATR-FTIR), and Confocal Raman Microscopy (CRM) confirmed the particles’ chemical homogeneity. The solubility and Partition coefficient (LogP) of Lactomorphin were determined by the analytical and computational methodology and revealed the hydrophilicity of Lactomorphin. A thermal degradation study was performed by exposing samples of solid-state Lactomorphin to a high temperature (62 °C) combined with zero relative humidity (RH) and to a high temperature (62 °C) combined with a high RH (75%) to evaluate the stability of Lactomorphin under these two different conditions. The solid-state processed particles exhibited excellent aerosol dispersion performance with an FDA-approved human DPI device to reach lower airways. The cell viability resazurin assay showed that Lactomorphin is safe up to 1000 μg/mL on nasal epithelium cells, lung cells, endothelial, and astrocyte brain cells.

Comparison of l-Carnitine and l-Carnitine HCL salt for targeted lung treatment of pulmonary hypertension (PH) as inhalation aerosols: Design, comprehensive characterization, in vitro 2D/3D cell cultures, and in vivo MCT-Rat model of PH

Disrupted l-Carnitine (L-Car) homeostasis has been implicated in the development of pulmonary hypertension (PH). L-Car has been administered orally and intravenously causing systemic side effects. To the authors’ knowledge, there are no reports using L-Car or L-Car HCl as an inhaled aerosol through the respiratory route in a targeted manner either from dry powder inhaler (DPI) or liquid delivery system. The purpose of the comprehensive and systematic comparative study between L-Car and L-Car HCl salt was to design and develop dry powder inhalers (DPIs) of each. This was followed by comprehensive physicochemical characterization, in vitro cell viability as a function of dose on 2D human pulmonary cell lines from different lung regions and in vitro cell viability on 3D small airway epithelia human primary cells at the air-liquid interface (ALI). In addition in vitro transepithelial electrical resistance (TEER) in air-interface culture (AIC) conditions on 2D human pulmonary cell line and 3D small airway epithelia human primary cells was carried out. In vitro aerosol dispersion performance using three FDA-approved human DPI devices with different device properties was also examined. Following advanced spray drying under various conditions, two spray drying pump rates (low and medium) were found to successfully produce spray-dried L-Car powders while four spray drying pump rates (low, medium, medium-high, and high) all resulted in the production of spray-dried L-Car HCl powders. Raw L-Car and L-Car HCl were found to be crystalline. All SD powders retained crystallinity following spray drying and polymorphic interconversion in the solid-state was identified as the mechanism for retaining crystallinity after the advanced spray drying process. All SD powders aerosolized readily with all three human DPI devices. However, the in vitro dispersion parameters for the SD powders was not conducive for in vivo administration to rats in DPIs due to hygroscopicity and nanoaggreation. In vivo rat studies were successfully accomplished using inhaled liquid aerosols. Safety was successfully demonstrated in vivo in healthy Sprague Dawley rats. Furthermore, therapeutic efficacy was successfully demonstrated in vivo in the monocrotaline (MCT)-rat model of PH after two weeks of daily L-Car inhalation aerosol treatment.

Inhalable Nanoparticles/Microparticles of an AMPK and Nrf2 Activator for Targeted Pulmonary Drug Delivery as Dry Powder Inhalers

Metformin is an activator of the AMPK and Nrf2 pathways which are important in the pathology of several complex pulmonary diseases with unmet medical needs. Organic solution advanced spray drying in the absence of water in closed-mode was used to design and develop respirable dry powders. Following comprehensive characterization, the influence of physicochemical properties was correlated with performance as aerosols using inertial impaction and three different human dry powder inhaler (DPI) devices varying in device properties. In vitro cell assays were conducted to test safety in 2D human pulmonary cell lines and in 3D small airway epithelia comprising primary cells at the air-liquid interface (ALI). In addition, in vitro transepithelial electrical resistance (TEER) was carried out. Metformin remained crystalline following advanced spray drying under these conditions. All SD powders consisted of nanoparticles/microparticles in the solid state. In vitro aerosol dispersion performance showed high aerosolization for all SD metformin powders with all DPI devices tested. High emitted dose for all powders with all three DPI devices was measured. Differences in other aerosol performance parameters and the interplay between the properties of different formulations produced at specific pump rates and the three different DPI devices were correlated with spray drying pump rate and device properties. Safety over a wide metformin dose range was also demonstrated in vitro. Aerosol delivery of metformin nanoparticles/microparticles has the potential to be a new “first-in-class” therapeutic for the treatment of a number of pulmonary diseases including pulmonary vascular diseases such as pulmonary hypertension.

Advanced spray dried proliposomes of amphotericin B lung surfactant-mimic phospholipid microparticles/nanoparticles as dry powder inhalers for targeted pulmonary drug delivery

The purpose of this study was to design, develop and characterize inhalable proliposomal microparticles/nanoparticles of Amphotericin B (AmB) with synthetic phospholipids, dipalmitoylphosphatidylcholine (DPPC) and dipalmitoylphosphatidylglycerol (DPPG) which are lung surfactant-mimic phospholipids. Organic solutions of AmB and phospholipids, were co-spray dried using an advanced closed-mode system and a high performance cyclone. Scanning electron microscopy (SEM) was employed to visualize the surface structure, morphology, and particles size. The residual water content of the proliposomes was quantified by Karl Fisher coulometric titration (KFT). Degree of crystallinity/non-crystallinity was measured by X-ray powder diffraction (XRPD). Phase behavior was measured by differential scanning calorimetry. The chemical composition by molecular fingerprinting was established using attenuated total reflectance (ATR)-Fourier-transform infrared (FTIR) spectroscopy. The amount of AmB loaded into the proliposomes was quantified using UV-VIS spectroscopy. The in vitro aerosol dispersion performance was conducted using the Next Generation Impactor (NGI) and the human dry powder inhaler (DPI) (Handihaler®) that is FDA-approved. Different human lung cell lines were employed to demonstrate in vitro safety as a function of dose and formulation. Smooth, spherical microparticles/nanoparticles were formed at medium and high spray drying pump rates and had low residual water content. A characteristic peak in the XRPD diffraction pattern as well as an endotherm in DSC confirmed the presence of the lipid bilayer structure characteristic in the DPPC/DPPG proliposomal systems. Superior in vitro aerosol performance was achieved with engineered microparticles/nanoparticles demonstrating suitability for targeted pulmonary drug delivery as inhalable dry powders. The in vitro cellular studies demonstrated that the formulated proliposomes are safe. These AmB proliposomes can be a better option for targeted treatment of severe pulmonary fungal infections.

An effective approach to modify the inhalable betamethasone powders based on morphology and surface control using a biosurfactant

Morphology control is one of the major aspects associated with the preparation of fine powders for the particle design of dry powder inhaler (DPI) formulations. We used betamethasone (BMZ) as the model steroid drug for DPI formulations and sodium surfactin (SF-Na) as the biosurfactant to modify the surface of the BMZ particles. Two types of BMZ particles with different crystal states, which exhibit different morphological properties, can be obtained using the spray-drying and freeze-drying method.The aerosol dispersion performance of the formulations measured using an Andersen cascade impactor revealed that the fine particle fractions of the BMZ/SF-Na (4/1) SDPs and FDPs are 53.4% ± 4.7% and 17.1% ± 3.4%, respectively. High aerosol performance of the BMZ spray-dried formulation may be achieved using SF-Na because the presence of SF-Na on the surface of the formulation plays an essential role in aggregate prevention. The results indicate that biosurfactant-assisted morphological control may be used to obtain fine particles for efficient pulmonary delivery.

Thermosensitive polysaccharide particles for pulmonary drug delivery

In the present study, we have prepared drug carriers for pulmonary administration: temperature-responsive polysaccharide particles prepared through an emulsion formation and a subsequent sol-gel transition of polysaccharides. The particles are obtained by the cooling of w/o (water-in-oil) emulsions prepared from an aqueous polysaccharide solution and a surfactant-dissolving organic solvent. We found that highly stable s/o (solid-in-oil) suspensions were formed regardless of HLB value, structure, and composition of the surfactants when high-molecular-weight surfactants were used. There are two possible important factors affecting the formation of spherical κ-carrageenan particles: (1) the formation of physically crosslinked domains inside the particle by means of the increase of concentrations of polysaccharides and cations and (2) the formation of a stable solid-liquid interfaces by using high-molecular-weight surfactants. We obtained stable polysaccharide particles with dimpled surfaces. As a result of the in vitro aerosol dispersion performance of the κ-carrageenan particles with the cascade impactor, we identified the characteristic delivery behavior of κ-carrageenan particles: the κ-carrageenan particles delivered more to the alveoli than to the pharynx and bronchi, despite their high density. The present study shows that the “dimpled” κ-carrageenan particles can likely stay in the alveoli so that high therapeutic effects will likely occur in pulmonary administration.

Evaluation of Granulated Lactose as a Carrier for Dry Powder Inhaler Formulations 2: Effect of Drugs and Drug Loading

Previously, granulated lactose carriers were shown to improve uniformity and aerosolization of a low-dose model drug. In the present study, the blending uniformity and aerosol dispersion performance were assessed for 2 model drugs salbutamol sulfate (SS) and rifampicin (RIF), blended at high loadings (10% or 30% drug) with granulated lactose carriers. The model drug powders differed in particle size distribution, morphology, density, and surface energies. Content uniformity of RIF blends was better than that of SS. Aerosolization studies showed that all blend formulations had acceptable emitted fractions (>70%). The SS blends showed low induction-port deposition (6%-10%) compared to RIF (5%-30%). This difference was greater at high flow rates. At 90 L/min, the low induction port deposition of SS blends allowed high fine particle fraction (FPF) of 73%-81%, whereas the FPF of the RIF blends was around 43%-45% with higher induction port deposition. However, SS blends exhibited strong flow rate–dependent performance. Increasing the flow rate from 30 L/min to 90 L/min increased SS FPF from approximately 20% to 80%. Conversely, RIF blends were flow rate and drug loading independent. It was concluded that the aerosolization of high drug–loaded dry powder inhaler formulations using granulated lactose, particularly flow rate dependency, varies with active pharmaceutical ingredient properties.

Preparation and physicochemical characterization of spray-dried and jet-milled microparticles containing bosentan hydrate for dry powder inhalation aerosols.

The objectives of this study were to prepare bosentan hydrate (BST) microparticles as dry powder inhalations (DPIs) via spray drying and jet milling under various parameters, to comprehensively characterize the physicochemical properties of the BST hydrate microparticles, and to evaluate the aerosol dispersion performance and dissolution behavior as DPIs. The BST microparticles were successfully prepared for DPIs by spray drying from feeding solution concentrations of 1%, 3%, and 5% (w/v) and by jet milling at grinding pressures of 2, 3, and 4 MPa. The physicochemical properties of the spray-dried (SD) and jet-milled (JM) microparticles were determined via scanning electron microscopy, atomic force microscopy, dynamic light scattering particle size analysis, Karl Fischer titration, surface analysis, pycnometry, differential scanning calorimetry, powder X-ray diffraction, and Fourier transform infrared spectroscopy. The in vitro aerosol dispersion performance and drug dissolution behavior were evaluated using an Anderson cascade impactor and a Franz diffusion cell, respectively. The JM microparticles exhibited an irregular corrugated surface and a crystalline solid state, while the SD microparticles were spherical with a smooth surface and an amorphous solid state. Thus, the in vitro aerosol dispersion performance and dissolution behavior as DPIs were considerably different due to the differences in the physicochemical properties of the SD and JM microparticles. In particular, the highest grinding pressures under jet milling exhibited excellent aerosol dispersion performance with statistically higher values of 56.8%±2.0% of respirable fraction and 33.8%±2.3% of fine particle fraction and lower mass median aerodynamic diameter of 5.0±0.3 μm than the others (P<0.05, analysis of variance/Tukey). The drug dissolution mechanism was also affected by the physicochemical properties that determine the dissolution kinetics of the SD and JM microparticles, which were well fitted into the Higuchi and zero-order models, respectively.

Phospholipid-based pyrazinamide spray-dried inhalable powders for treating tuberculosis

Sterilization of necrotic granulomas containing Mycobacterium tuberculosis is difficult by oral and parenteral drug delivery of antitubercular drugs. Pulmonary delivery of these drugs should increase the concentration of drug in the granulomas and, thereby, improve the sterilization. The current study aimed to develop spray-dried (SD) powders composed of pyrazinamide, 1,2-dipalmitoyl-sn-glycero-3-phosphatidylcholine (DPPC), 1,2-distearoyl-sn-glycero-3-phosphoethanolamine N-(carbonyl-methoxy polyethylene glycol-2000) (DSPE-PEG2k) and l-leucine to improve drug delivery to the deeper lung. Pyrazinamide SD powders with varying amounts of DPPC (5, 15 and 25% w/w) were produced using a BUCHI B-290 Mini Spray-Dryer. The powders were characterized physicochemically and for their aerosol dispersion performance using a Next Generation Impactor (NGI). All the SD powders had a narrow particle size distribution (1.29–4.26μm) with low residual moisture (<2%). Solid state characterization confirmed that the α-polymorphic crystalline pyrazinamide transformed into the γ-polymorphic form during spray-drying. SD pyrazinamide (PDDL0) without excipients showed very poor aerosolization with a fine particle fraction (FPF%) of 8.5±1.0%. However, the SD powder with 25% w/w DPPC (PDDL3) exhibited the best aerosolization with a FPF of 73.2±4.0%. Incorporating high amounts of DPPC improved aerosolization of SD powders; however further evaluation of the developed inhalation powders is necessary to determine their therapeutic potential for treating pulmonary tuberculosis.

In Vitro Pulmonary Cell Culture in Pharmaceutical Inhalation Aerosol Delivery: 2-D, 3-D, and In Situ Bioimpactor Models

The use of non-invasive inhaled aerosols for pulmonary drug delivery continues to grow. This is due to the many unique advantages this delivery route offers for the treatment of both local and systemic diseases. The physicochemical properties of the formulated drugs as well as the physiology of the lungs play a key role in both the deposition and absorption of the particles. The airway and the alveolar epithelium are targets for the treatment of respiratory diseases. However, particles have to overcome biological barriers before they reach their target and produce an effect. In vitro aerosol dispersion performance (i.e. aerodynamic size and aerodynamic size distribution) of inhalable particles is quantified by inertial impaction, as required by regulatory agencies for an investigational pharmaceutical inhalation aerosol formulation to be approved for use in patients as a marketed pharmaceutical product. Using inertial impaction in conjunction with cell cultures of various pulmonary cells in situ as bioimpactors has unique aspects in correlating aerodynamic properties with pulmonary cellular behavior including viability and uptake. These can be as co-culture or in single culture, as 3-D multicellular spheroids or 2-D cellular monolayer using different conditions to grow them, such as air-liquid interface culture (ALI) or in liquid covered culture (LCC). evaluation of the currently available in vitro models and the challenges in developing reliable cellular tools to predict the deposition of inhalable particles in the lungs as a function of aerodynamic particle properties is presented in the manuscript. The mechanistic aerodynamic and biophysical properties of inhaled aerosol particles on the entire respiratory tract at the cellular level based on aerodynamic size and aerodynamic size distribution will be better understood with the development of in vitro methods which are described in this work.

Effect of compression pressure on inhalation grade lactose as carrier for dry powder inhalations.

Introduction:This study focused on the potential effects of compression forces experienced during lactose (InhaLac 70, 120, and 230) storage and transport on the flowability and aerosol performance in dry powder inhaler formulation.Materials and Methods:Lactose was subjected to typical compression forces 4, 10, and 20 N/cm2. Powder flowability and particle size distribution analysis of un-compressed and compressed lactose was evaluated by Carr's index, Hausner's ratio, the angle of repose and by laser diffraction method. Aerosol performance of un-compressed and compressed lactose was assessed in dispersion studies using glass twin-stage-liquid-impenger at flow rate 40-80 L/min.Results:At compression forces, the flowability of compressed lactose was observed same or slightly improved. Furthermore, compression of lactose caused a decrease in in vitro aerosol dispersion performance.Conclusion:The present study illustrates that, as carrier size increases, a concurrent decrease in drug aerosolization performance was observed. Thus, the compression of the lactose fines onto the surfaces of the larger lactose particles due to compression pressures was hypothesized to be the cause of these observed performance variations. The simulations of storage and transport in an industrial scale can induce significant variations in formulation performance, and it could be a source of batch-to-batch variations.

Formulation and characterization of inhalable magnetic nanocomposite microparticles (MnMs) for targeted pulmonary delivery via spray drying

Targeted pulmonary delivery facilitates the direct application of bioactive materials to the lungs in a controlled manner and provides an exciting platform for targeting magnetic nanoparticles (MNPs) to the lungs. Iron oxide MNPs remotely heat in the presence of an alternating magnetic field (AMF) providing unique opportunities for therapeutic applications such as hyperthermia. In this study, spray drying was used to formulate magnetic nanocomposite microparticles (MnMs) consisting of iron oxide MNPs and d-mannitol. The physicochemical properties of these MnMs were evaluated and the in vitro aerosol dispersion performance of the dry powders was measured by the Next Generation Impactor®. For all powders, the mass median aerosol diameter (MMAD) was <5μm and deposition patterns revealed that MnMs could deposit throughout the lungs. Heating studies with a custom AMF showed that MNPs retain excellent thermal properties after spray drying into composite dry powders, with specific absorption ratios (SAR)>200W/g, and in vitro studies on a human lung cell line indicated moderate cytotoxicity of these materials. These inhalable composites present a class of materials with many potential applications and pose a promising approach for thermal treatment of the lungs through targeted pulmonary administration of MNPs.

Development of dry powder inhaler formulation loaded with alendronate solid lipid nanoparticles: solid-state characterization and aerosol dispersion performance

Alendronate sodium is a bisphosphonate drug used for the treatment of osteoporosis and acts as a specific inhibitor of osteoclast-mediated bone resorption. Inhalable solid lipid nanoparticles (SLNs) of the alendronate were successfully designed and developed by spray-dried and co-spray dried inhalable mannitol from aqueous solution. Emulsification technique using a simple homogenization method was used for preparation of SLNs. In vitro deposition of the aerosolized drug was studied using a Next Generation Impactor at 60 L/min following the methodology described in the European and United States Pharmacopeias. The Carr’s Index, Hausner ratio and angle of repose were calculated as suitable criteria for estimation of the flow behavior of solids. Scanning electron microscopy showed spherical particle morphology of the respirable particles. The proposed spray-dried nanoparticulate-on-microparticles dry powders displayed good aerosol dispersion performance as dry powder inhalers with high values in emitted dose, fine particle fraction and mass median aerodynamic diameter. These results indicate that this novel inhalable spray-dried nanoparticulate-on-microparticles aerosol platform has great potential in systemic delivery of the drug.

Design, Characterization, and Aerosol Dispersion Performance Modeling of Advanced Co-Spray Dried Antibiotics with Mannitol as Respirable Microparticles/Nanoparticles for Targeted Pulmonary Delivery as Dry Powder Inhalers

Dry powder inhalation aerosols of antibiotic drugs (a first-line aminoglycoside, tobramycin, and a first-line macrolide, azithromycin) and a sugar alcohol mucolytic agent (mannitol) as co-spray dried (co-SD) particles at various molar ratios of drug:mannitol were successfully produced by organic solution advanced co-spray drying from dilute solute concentration. These microparticulate/nanoparticulate aerosols consisting of various antibiotic drug:mannitol molar ratios were rationally designed with a narrow and unimodal primary particle size distribution, spherical particle shape, relatively smooth particle surface, and very low residual water content to minimize the interparticulate interactions and enhance in vitro aerosolization. These microparticulate/nanoparticulate inhalation powders were high-performing aerosols as reflected in the aerosol dispersion performance parameters of emitted dose, fine particle fraction (FPF), respirable fraction (RF), and mass median aerodynamic diameter (MMAD). The glass transition temperature (Tg) values were significantly above room temperature, which indicated that the co-SD powders were all in the amorphous glassy state. The Tg values for co-SD tobramycin:mannitol powders were significantly lower than those for co-SD azithromycin:mannitol powders. The interplay between aerosol dispersion performance parameters and Tg was modeled where higher Tg values (i.e., more ordered glass) were correlated with higher values in FPF and RF and lower values in MMAD.