Adsorption Of Polyethylene Research Articles

Adsorption mechanism of cefradine on three microplastics: A combined molecular dynamics simulation and density functional theory calculation study

Microplastics and antibiotics are receiving increasing attention as two emerging pollutants in the aquatic ecosystem. The absorption of antibiotics by microplastics can potentially intensify their impact on marine organisms and human health. However, the detailed mechanisms underlying this interaction remain to be elucidated. Through molecular dynamics (MD) simulations and density functional theory (DFT) calculations, this study investigated the adsorption of cefradine (CED) onto three typical microplastics (MPs)-polyethylene (PE), polypropylene (PP), and polyamide (PA). The results of the molecular dynamics simulations showed that the interaction energy between CED and microplastics followed the order of PA-CED > PP-CED > PE-CED, indicating that PA microplastics had the highest adsorption capacity for CED antibiotics. The total energy contribution of the microplastics-cefradine (MPs-CED) systems suggested that the van der Waals and electrostatic interactions were the two primary mechanisms for the adsorption of CED by these three microplastics. In DFT calculations, the adsorption of CED on PA was found to be significantly influenced by both electrostatic and van der Waals effects, while the main driving force in the adsorption of PE and PP is van der Waals effect. In addition, IGMH analysis and AIM topological analysis confirmed that the adsorption of CED on PA relied heavily on the synergistic effect of hydrogen bonding and the van der Waals effect. The findings of this study validate the results obtained from molecular dynamics simulations, laying a foundation for a comprehensive exploration of the interaction mechanisms between microplastics and organic pollutants by integrating MD simulations and DFT calculations.

The interaction mechanisms of algal organic matter (AOM) and various types and aging degrees of microplastics

Algal blooms can produce substantial amounts of algal organic matter (AOM). Microplastics (MPs) in aquatic environments inevitably interact with AOM. Meanwhile, the aging and type of MPs may increase the uncertainty surrounding interaction. This study focused on polyethylene (PE) and polylactic acid (PLA) to investigate their interaction with AOM before and after aging. The results shw that PLA has a stronger adsorption capacity for AOM than PE. Meanwhile, aging enhanced and weakened the adsorption of PE and PLA for AOM. Compared to unaged PE (UPE) and aged PLA (APLA), aged PE (APE) and unaged PLA (UPLA) more significantly promote the humification of AOM and alter its functional groups. 2D-IR-COS analysis reveals that the sequence of functional group changes in AOM interacting with MPs is influenced by the type and aging of MPs. After interacting with AOM, surface roughness increased for all MPs. FTIR and XPS analyses show that the addition of AOM accelerated the oxidation of MPs surfaces, especially for UPE and APLA, with oxygen content increasing by 9.32 % and 1 %. Aging enhances the interaction between PE and AOM, while weakening the interaction between PLA and AOM. These findings provide new insights into understanding the interplay between AOM and MPs.

Interaction characteristics and mechanism of Cr(VI)/Cr(III) with microplastics: Influence factor experiment and DFT calculation

The coexistence of highly toxic heavy metal chromium and new pollutants microplastics has been widely present, and the interaction behavior and mechanism of the two are crucial for their environmental effects in coexisting environments, which urgently need to be further explored. Firstly, the interaction characteristics of polyamide (PA) and polyethylene (PE) with Cr(VI)/Cr(III) were investigated, where PA exhibited higher adsorption capacity of both Cr(VI) and Cr(III) than PE among various environmental conditions. The higher adsorption energy of PA on Cr(VI)/Cr(III) was also achieved by DFT calculation, and the bending configuration of PA during the adsorption process may be beneficial for its interaction with Cr. Then, the combination of characterization analysis and DFT calculation showed that significant chemical bonding occurred in the interaction between CO bond of PA and Cr(III), weak chemical interactions occurred in the adsorption of PE with Cr(III) and PA with Cr(VI), while the adsorption of PE with Cr(VI) was mainly physical effects. This study provides theoretical support for pollution control of microplastics and chromium in co-existing environment.

Characteristics and Mechanism of Cd Release and Transport in Soil Contaminated with PE-Cd

Microplastics （MPs） are a type of emerging contaminants that pose a potential threat to global terrestrial ecosystems. The accumulation of MPs in soil inevitably affects soil physical and chemical properties， both directly and indirectly. Additionally， owing to their small size and surface features， MPs have excellent sorption capacity for both organic and inorganic materials， thus affecting their fate in the environment. However， the influence of MPs on heavy metal sorption and transport in soil is still not fully understood. In this study， polyethylene （PE） and Cd were selected as research objects， and on the basis of clarifying the adsorption mechanism of Cd on PE MPs， the effects of PE concentration and particle size on Cd release and transport behavior in soil under different ionic strengths and types （Ca2+ and Na+） were studied using column leaching experiments. The results of the batch experiments showed that the adsorption capacity of PE MPs for Cd2+ decreased with the increase in particle size. Scanning electron microscopy （SEM）， Fourier transform infrared spectroscopy （FTIR）， and Zeta potential were used to analyze the properties of PE MPs and adsorption behavior of Cd2+ onto MPs. The adsorption was mainly a physical process and was controlled by intra-particle diffusion. The adsorption kinetics could be described well by the quasi-second-order kinetics and Webber-Morris model. The adsorption isotherm conformed to the Langmuir model， indicating monolayer adsorption. The results of leaching experiments showed that the effect of PE MPs on Cd release and transport in soil was related to the CaCl2 concentration. At high ionic strength （0.05 mol·L-1 and 0.1 mol·L-1）， PE promoted the transport of Cd. The effluent concentration of Cd2+ increased from 6.48 mg·L-1 and 16.79 mg·L-1 to 7.12 mg·L-1 and 23.45 mg·L-1， whereas at low ionic strength （0.01 mol·L-1）， Cd transport was inhibited by PE MPs， and the effluent concentration of Cd2+ decreased from 0.66 mg·L-1 to 0.57 mg·L-1. The larger the amount of PE added， the more significant the promoting or inhibiting effect. Additionally， the release and transport of Cd in soil were also affected by the MPs particle size and concentration. When the addition amount was small （1%， 4%）， the large-sized MPs were more conducive to the transport of Cd in soil. When the addition amount was large （7%， 20%）， MPs with small particle sizes promoted Cd2+ transport more significantly. When the leaching solution used was NaCl， soil permeability decreased significantly. PE MPs had no significant effect on Cd release and transport but changed the stability of soil aggregates. In conclusion， PE MPs could change the release and transport behavior of Cd in soil， and the impact results were not only related to the particle size and content of MPs but were also influenced by the chemical properties of the soil solution.

Adsorption-desorption behavior of florpyrauxifen-benzyl on three microplastics in aqueous environment as well as its mechanism and various influencing factors

Microplastics (MPs) and pesticides are two categories contaminants with proposed negative impacts to aqueous ecosystems, and adsorption of pesticides on MPs may result in their long-range transport and compound combination effects. Florpyrauxifen-benzyl, a novel pyridine-2-carboxylate auxin herbicide has been widely used to control weeds in paddy field, but the insights of which are extremely limited. Therefore, adsorption and desorption behaviors of florpyrauxifen-benzyl on polyvinyl chloride (PVC), polyethylene (PE) and disposable face masks (DFMs) in five water environment were investigated. The impacts of various environmental factors on adsorption capacity were evaluated, as well as adsorption mechanisms. The results revealed significant variations in adsorption capacity of florpyrauxifen-benzyl on three MPs, with approximately order of DFMs > PE > PVC. The discrepancy can be attributed to differences in structural and physicochemical properties, as evidenced by various characterization analysis. The kinetics and isotherm of florpyrauxifen-benzyl on three MPs were suitable for different models, wherein physical force predominantly governed adsorption process. Thermodynamic analysis revealed that both high and low temperatures weakened PE and DFMs adsorption, whereas temperature exhibited negligible impact on PVC adsorption. The adsorption capacity was significantly influenced by most environmental factors, particularly pH, cations and coexisting herbicide. This study provides valuable insights into the fate of florpyrauxifen-benzyl in presence of MPs, suggesting that PVC, PE and DFMs can serve as carriers of florpyrauxifen-benzyl in aquatic environment.

Clay minerals/sodium alginate/polyethylene hydrogel adsorbents control the selective adsorption and reduction of uranium: Experimental optimization and Monte Carlo simulation study

Clay minerals formations are potential geological barrier (host rocks) for the long-rerm storage of uranium tailing in deep geological repositories. However, there are still obstacles to the efficient retardation of uranium because of the competition between negatively charged regions at the clay minerals end face, surface and between layers, as well as low mineralization capacity. Herein, employing a simple method, we used sodium alginate (SA), an inexpensive natural polymer material, polyethylene (PE), and the natural clay minerals montmorillonite (Mt), nontronite (Nt), and beidellite (Bd) to prepare three hydrogel adsorbents, (denoted as Mt/PE-@SA, Nt/PE-@SA, and Bd/PE-@SA), respectively. The application of obtained hydrogel adsorbents further extends to uranium(VI) removal from aqueous. Due to the synergistic action of SA group and PE group, hydrogel adsorbents showed select adsorption and mineralization effect on uranium(VI), among which the maximum uranium(VI) adsorption capacity of Nt/PE-@SA was 133.3 mg·g-1 and Mt/PE-@SA exhibited strong selectivity for uranium(VI) in the presence of coexisting metal ions. Cyclic voltammetry studies indicated the mitigation and immobilization of uranium species onto adsorbents by both reduction and mineralization. Besides, the synergistic adsorption of SA and PE on clay minerals was hypothesized, and the idea was supported by structure optimizations results from Monte Carlo dynamics simulation (MCD). Three obtained hydrogel adsorbents structural model was constructed based on its physicochemical characterization, the low energy adsorption sites and adsorption energies are investigated using MCD simulation. The simulation results show that obtained hydrogel adsorbents have a strong interaction with uranium(VI), which ensures the high adsorption capacity of those materials. Most importantly, this work demonstrates a new strategy for preparing mineral-based hydrogel adsorbents with enough stability and provides a new perspective for uranium(VI) removal in complex environment.

Mechanistic Understanding of Efficient Polyethylene Hydrocracking over Two‐Dimensional Platinum‐Anchored Tungsten Trioxide

AbstractChemical upcycling of polyethylene (PE) can convert plastic waste into valuable resources. However, engineering a catalyst that allows PE decomposition at low temperatures with high activity remains a significant challenge. Herein, we anchored 0.2 wt.% platinum (Pt) on defective two‐dimensional tungsten trioxide (2D WO3) nanosheets and achieved hydrocracking of high‐density polyethylene (HDPE) waste at 200–250 °C with a liquid fuel (C5–18) formation rate up to 1456 gproducts ⋅ gmetal species−1 ⋅ h−1. The reaction pathway over the bifunctional 2D Pt/WO3 is elucidated by quasi‐operando transmission infrared spectroscopy, where (I) well‐dispersed Pt immobilized on 2D WO3 nanosheets trigger the dissociation of hydrogen; (II) adsorption of PE and activation of C−C cleavage on WO3 are through the formation of C=O/C=C intermediates; (III) intermediates are converted to alkane products by the dissociated H. Our study directly illustrates the synergistic role of bifunctional Pt/WO3 catalyst in the hydrocracking of HDPE, paving the way for the development of high‐performance catalysts with optimized chemical and morphological properties.

Mechanistic Understanding of Efficient Polyethylene Hydrocracking over Two-Dimensional Platinum-Anchored Tungsten Trioxide.

Chemical upcycling of polyethylene (PE) can convert plastic waste into valuable resources. However, engineering a catalyst that allows PE decomposition at low temperatures with high activity remains a significant challenge. Herein, we anchored 0.2 wt.% platinum (Pt) on defective two-dimensional tungsten trioxide (2D WO3 ) nanosheets and achieved hydrocracking of high-density polyethylene (HDPE) waste at 200-250 °C with a liquid fuel (C5-18 ) formation rate up to 1456 gproducts ⋅ gmetal species -1 ⋅ h-1 . The reaction pathway over the bifunctional 2D Pt/WO3 is elucidated by quasi-operando transmission infrared spectroscopy, where (I) well-dispersed Pt immobilized on 2D WO3 nanosheets trigger the dissociation of hydrogen; (II) adsorption of PE and activation of C-C cleavage on WO3 are through the formation of C=O/C=C intermediates; (III) intermediates are converted to alkane products by the dissociated H. Our study directly illustrates the synergistic role of bifunctional Pt/WO3 catalyst in the hydrocracking of HDPE, paving the way for the development of high-performance catalysts with optimized chemical and morphological properties.

Adsorption mechanism of two pesticides on polyethylene and polypropylene microplastics: DFT calculations and particle size effects

Polyethylene (PE) and polypropylene (PP) microplastics (MPs), as carriers, can bind with pesticides, which propose harmful impacts to aqueous ecosystems. Meanwhile, carbofuran and carbendazim (CBD), two widely used carbamate pesticides, are toxic to humans because of the inhibition of acetylcholinesterase activity. The interaction between two MPs and two pesticides could start in farmland and be maintained during transportation to the ocean. Herein, the adsorption behavior and mechanism of carbofuran and carbendazim (CBD) by PE and PP MPs were investigated via characterization and density functional theory (DFT) simulation. The adsorption kinetic and thermodynamic data were best described by pseudo-second-order kinetics and the Freundlich models. The adsorption behaviors of individual carbofuran/CBD on both MPs were very similar. The CBD adsorption rate and capacity of PE and PP MPs were higher than those of carbofuran. This phenomenon explained the lower negative effects of DOM (oxalic acid, glycine (Gly)) on CBD adsorption relative to those of carbofuran. The presence of oxalic acid and Gly decreased the PE adsorption by 20.40–48.02% and the PP adsorption by 19.27–42.11%, respectively. It indicated the significance of DOM in carbofuran cycling. The adsorption capacities were negatively correlated with MPs size, indicating the importance of specific surficial area. Fourier transformation infrared spectroscopy before and after adsorption suggested that the adsorption process did not produce any new covalent bond. Instead, intermolecular van der Waals forces were one of the primary adsorption mechanisms of carbofuran and CBD by MPs, as evidenced by DFT calculations. Based on the zeta potential, the electrostatic interaction explained the higher adsorption CBD by MPs than carbofuran.

Synergistic effect of the co-pyrolysis of cardboard and polyethylene: A kinetic and thermodynamic study

Pyrolysis of municipal solid waste (MSW) represents one of the most promising solutions to recycle materials and recover energy. Two of the main components of MSW are waste cardboard and plastic. In this study, the pyrolysis of cardboard and polyethylene (PE) and the co-pyrolysis of their mixtures were conducted to investigate the synergistic effect by using thermogravimetric analysis. The whole reaction process was divided into four pseudoreactions, namely, hemicellulose, lignin, cellulose, and PE, by using the Frazer-Suzuki deconvolution method. It was found that the co-pyrolysis of cardboard and PE could promote the decomposition degrees of cardboard from 70.28% to 75.31%, when the PE fraction increased from 0 to 75%. However, the presence of cardboard can hinder the heat adsorption of PE, which shifts the peak of the PE reaction to a higher temperature. This results in higher Ea and ΔH‡ values for PE pyrolysis with an increasing fraction of cardboard. On the other hand, the Ea and ΔH‡ values of cellulose pyrolysis have their lowest values when the mixing rate is around 50%. This research deepens the understanding of the synergistic effect of co-pyrolysis of cardboard and PE, which supports the potential application of pyrolysis of MSW.

Upcycling Single-Use Polyethylene into High-Quality Liquid Products.

Our civilization relies on synthetic polymers for all aspects of modern life; yet, inefficient recycling and extremely slow environmental degradation of plastics are causing increasing concern about their widespread use. After a single use, many of these materials are currently treated as waste, underutilizing their inherent chemical and energy value. In this study, energy-rich polyethylene (PE) macromolecules are catalytically transformed into value-added products by hydrogenolysis using well-dispersed Pt nanoparticles (NPs) supported on SrTiO3 perovskite nanocuboids by atomic layer deposition. Pt/SrTiO3 completely converts PE (Mn = 8000–158,000 Da) or a single-use plastic bag (Mn = 31,000 Da) into high-quality liquid products, such as lubricants and waxes, characterized by a narrow distribution of oligomeric chains, at 170 psi H2 and 300 °C under solvent-free conditions for reaction durations up to 96 h. The binding of PE onto the catalyst surface contributes to the number averaged molecular weight (Mn) and the narrow polydispersity (Đ) of the final liquid product. Solid-state nuclear magnetic resonance of 13C-enriched PE adsorption studies and density functional theory computations suggest that PE adsorption is more favorable on Pt sites than that on the SrTiO3 support. Smaller Pt NPs with higher concentrations of undercoordinated Pt sites over-hydrogenolyzed PE to undesired light hydrocarbons.

Effect of mixing temperature on the carbon nanofiller distribution in immiscible blends of polycarbonate and polyolefin

We studied the selective localization of carbon nanofillers, such as multi-walled carbon nanotube (MWCNT) and graphene nanoplatelet (GNP), in immiscible polymer blends composed of polycarbonate (PC) and polyethylene (PE) or ethylene-propylene copolymer (EPR). It was found that the distribution state of the carbon nanofillers in the composites is greatly affected by the mixing temperature and the species of nanofillers. MWCNTs resided in the PE or EPR phase in the composites, which cannot be explained by the difference in the interfacial tension. A similar morphology was detected in the PC/GNP/PE composite prepared at 300°C. In contrast, the PC/GNP/PE composite prepared at the low temperature (250°C) and the PC/GNP/EPR composites have the carbon nanofillers mostly in the PC phase. The selective localization in the PE or EPR phase is attributed to the surface adsorption of PE or EPR chains on the carbon nanofillers, which is more obvious for PE and at the high mixing temperature. These results demonstrate that both the species of carbon nanofillers and the mixing temperature affect the carbon nanofiller distribution in the immiscible blends.

Polymer Adsorption on Graphite and CVD Graphene Surfaces Studied by Surface-Specific Vibrational Spectroscopy.

Sum-frequency vibrational spectroscopy was employed to probe polymer contaminants on chemical vapor deposition (CVD) graphene and to study alkane and polyethylene (PE) adsorption on graphite. In comparing the spectra from the two surfaces, it was found that the contaminants on CVD graphene must be long-chain alkane or PE-like molecules. PE adsorption from solution on the honeycomb surface results in a self-assembled ordered monolayer with the C-C skeleton plane perpendicular to the surface and an adsorption free energy of ∼42 kJ/mol for PE(H(CH2CH2)nH) with n ≈ 60. Such large adsorption energy is responsible for the easy contamination of CVD graphene by impurity in the polymer during standard transfer processes. Contamination can be minimized with the use of purified polymers free of PE-like impurities.

Structural and elastic properties and stability characteristics of oxygenated carbon nanotubes under physical adsorption of polymers

The importance of covalent and non-covalent functionalization approaches for modification the properties of carbon nanotubes is being more widely recognized. To this end, elastic properties and buckling behavior of oxygenated CNT with atomic oxygen and hydroxyl under physical adsorption of PE (Polyethylene) and PEO (Poly (ethylene oxide)) are determined through employing the molecular dynamics (MD) simulations. The results demonstrate that non-covalent bonding of polymer on the surface of oxygenated CNT causes reductions in the variations of critical buckling load and critical strain compared to oxygenated CNTs. Critical buckling load and critical strain of oxygenated CNT/polymer are higher than those of oxygenated CNT. Also, it is demonstrated that critical buckling load and critical strain values in the case of oxygenated CNT/polymer are independent of polymer type unlike the value of Young's modulus. It is shown that variations of Young's modulus decrease as PE adsorbed on the surface of oxygenated CNT. Moreover, the presence of oxygen atom on PEO chain leads to bigger variations of Young's modulus with weight percentage of chemisorbed component, i.e. atomic oxygen and hydroxyl. It is also demonstrated that Young's modulus reduces more considerably in the presence of PEO chain compared to PE one.

ADSORPTION AND DIFFUSION PROCESSES OF POLYETHYLENE ON SILICON (111) SURFACE STUDIED BY MOLECULAR DYNAMICS SIMULATION

The adsorption of polyethylene with different chain lengths on a silicon (111) surface is studied via molecular dynamics simulations. The relative dielectric constant is selected to be 1 and 78.0 to mimic in vacuum and in solution environment, respectively. Different configurations and dynamic properties are found in the two absolutely different environments, showing that the solvent condition plays an obvious role in the process of chain adsorption and diffusion on the hydrophobic surface. The chain all present as two-dimensional (2D) adsorption configuration on the surface. The adsorption energy of different chain lengths follows a linear function, and the average adsorption energy per segment is -1.58 kcal/mol. In addition, the diffusion coefficient (D) of such chains scales with the degree of polymerization (N) as N-3/2.

Characterization of ethylene‐propylene copolymers with high‐temperature gradient adsorption liquid chromatography and CRYSTAF

AbstractBlends of linear polyethylene (PE) and isotactic polypropylene (iPP) with different average molar masses and a series of ethylene‐propylene (EP) copolymers with different chemical composition as well as blends of PE, Ipp, and EP copolymers were separated using a carbon‐column packing (Hypercarb®) and gradients of 1‐decanol or 2‐ethyl‐1‐hexanol → 1,2,4‐trichlorobenzene (TCB). The separation is based on full adsorption of linear PE on the carbon sorbent at temperature 160°C. However, iPP is not adsorbed and elutes in size exclusion mode. The random EP copolymers have been adsorbed in the column packing and separated according to their average chemical composition after application of the gradient starting with alcohol and ending with pure TCB. The elution volumes of the copolymers depended linearly on the average concentration of ethylene in the copolymers. The HPLC elution profiles were correlated with the CRYSTAF elution profiles. In contrast to CRYSTAF, fully amorphous polyolefin samples were separated with the high‐temperature adsorption liquid chromatography. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011

Adsorption of polyethylene from solution onto starch film surfaces

AbstractWe prepared starch films by jet‐cooking aqueous dispersions of high‐amylose starch and then allowing the jet‐cooked dispersions to air‐dry on Teflon surfaces. When the starch films were immersed in 1% solutions of polyethylene (PE) in 1‐dodecanol, dodecane, and xylene at 120°C and the solutions were allowed to slowly cool, PE precipitated from the solutions and adsorbed onto the starch film surfaces. Fourier transform infrared spectroscopy was used to estimate the micrograms of PE adsorbed per square centimeter of starch film. PE was preferentially adsorbed onto the film side that was in contact with the Teflon surface during drying. The amount of PE adsorbed ranged from about 8 to 45 μg/cm2 and depended upon the solvent used and the final temperature of the cooled solution. Scanning electron microscopy of the starch film surfaces showed discontinuous networks of adsorbed PE on the Teflon side and widely spaced nodules of adsorbed PE on the air side. NMR analysis showed that the PE adsorbed onto the starch surface was more linear and/or had a higher molecular weight than the starting PE. Possible reasons for the selective adsorption of PE onto the Teflon side of the starch film surface are discussed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009

Automated Monitoring of the Establishment of the Adsorption Equilibrium: Adsorption of Polyethylene from 1,2,4‐Trichlorobenzene onto a Zeolite at Temperature 140∘C

The automated procedure for the monitoring of the adsorption process in the solute-sorbent-solvent system has been elaborated. It uses commercially available instrument CRYSTAF model 200. The application of CRYSTAF enabled monitoring of adsorption of linear polyethylene with weight average molar masses of 2, 14, and 53 kg/mol from 1,2,4-trichlorobenzene onto zeolite SH-300 at temperature as high as 140°C. It is the authors' understanding that this is the first demonstration of an adsorption isotherms for polyethylene. The measurement with the CRYSTAF instrument reduces manual manipulations with dangerous solvents at high temperature and enables automated long-time monitoring of the concentration of the solute in an adsorption system.

Selective removal of polyethylene or polypropylene from their blends based on difference in their adsorption behaviour

The adsorption of polyethylene and polypropylene on zeolites depends on the nature of zeolite, the solvent as well as the molar mass of the polymer sample. For example, linear polyethylene is strongly retained on zeolite SH-300 from decalin, while isotactic, syndiotactic or atactic polypropylene is fully eluted in this system. On the other hand, polypropylene is retained on zeolite CBV-780 from diphenylether, while linear polyethylene is eluted. These differences in the elution behaviour have been utilised for selective removal of either linear polyethylene or polypropylene from blends of both polymers. The desorption of the retained polymer is difficult, or at times impossible. However, the selected adsorption systems have complimentary character, i.e. either one or second component is eluted or fully retained. Thus these sorbent/solvent systems, identified herein, are the first isocratic chromatographic systems, which enable selectively to remove polyethylene or polypropylene from their mixture. Moreover, decalin/SH-300 enables the removal of both linear and branched polyethylene from mixtures with random ethylene/propylene copolymers (polyethylene fully retained, ethylene/propylene copolymers eluted).

Adsorption of Polyethylene and Polypropylene by Zeolites: Inside or Outside?

Adsorption of Polyethylene and Polypropylene by Zeolites: Inside or Outside?