Adsorbent For Wastewater Treatment Research Articles

Thermodynamic interpretation of cationic dye adsorption onto untreated coffee residues as adsorbents via statistical physics approach

In this current paper, we perform a theoretical examination of adsorption systems undertaken through the application of statistical physics modeling to experimental data Remacryl Red TGL (BR) dye adsorption isotherms onto the untreated coffee residues (UCR) based adsorbents at 298–338 K range. The experimental values exhibited a strong agreement with the predicted values, and the developed model received high approval. Significant parameters are theoretically discussed such as thermodynamic, energetic, and stereographic factors which determine the (BR) adsorption onto UCR. In the pursuit of unraveling the adsorption mechanism, four different models are adopted: a monolayer with one energy (Model 1), a monolayer with two horizontal energies (Model 2), a monolayer with three energies (Model 3) and a double-layer with two vertical energies (Model 4). The analysis considered both steric and energetic parameters associated with the adsorption reaction, namely the number of adsorbed particles per site (n1 and n2), the receptor sites density (N1m and N2m), and the concentration at half-saturation. It appears that the experimental data aligns well with a monolayer model characterized by two energy states. The variations in these factors are examined in relation to the temperature of absorption isotherms. More importantly, the calculation of adsorption energies unequivocally pointed out that the adsorption process is of a chemisorptive nature. Our findings indicate that (UCR) could be utilized as a low-cost alternative adsorbent in wastewater treatment to eliminate the Remacryl Red TGL (BR) dye.

Structural simulation and performance evaluation of a novel synthesized ZIF in the adsorption of MO from aqueous solutions.

Zeolitic imidazolate frameworks (ZIFs) are desirable materials widely applied as adsorbent for wastewater treatment. This study synthesizes and applies a novel structured ZIF with organic ligand of 2-methyl imidazole and metal salt of copper (II) sulfate as adsorbent. Its morphology and structure were investigated using Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscope, field emission scanning electron microscope, energy dispersive X-ray spectrometry, and mapping analysis. After structural analysis, the adsorbent structure was simulated and determined using Avogadro and Gaussian software. The removal efficiency of prepared ZIF in the removal of methyl orange from aqueous solution was evaluated. The effect of pH, the concentration of the dye in solution, dosage of the adsorbent, and the contact time between adsorbent and solution on the methyl orange removal were examined using central composite design of response surface methodology in five levels. The maximum dye removal of 99% was obtained for 2g adsorbent/L, pH of 3.3, and initial dye concentration of 121mg/L after 127min contact time. In addition, to reduce the economic costs and energy consumption, the synthesis time was also reduced and used to show the applicability of the adsorbent prepared and understand its advantages and disadvantages in removing methyl orange dye from aqueous solutions. This molecular adsorbent is stable, and it can be stored for months. On the other hand, this ZIF can be easily recovered and reused many times. In this research, after five times of recovery, there was no significant change in the effectiveness of the adsorbent.

Synthesis and characterization of the Cu(II)-quinoxaline, 3,3-thiodipropionate mixed ligand coordination polymer for the removal of methylene blue from aqueous solution

Herein, we report the removal of methylene blue (MB) dye from water by Cu(II)-quinoxaline, 3,3-thiodipropionate mixed ligand coordination polymer synthesized as [Cu2(TDPH)4(QNX)]·DMF. Characterization of the synthesized material was carried out by elemental analysis, thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), BET surface area analysis, X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), and UV–visible spectroscopy. ν(C = O) and ν(C–O) absorption bands were detected at 1735 and 1093 cm−1, respectively, while ν(C = N) was observed at 1608 cm−1 in the synthesized compound. The synthesized material was used as adsorbent for the removal of MB dye from aqueous solution using batch adsorption technique. The maximum adsorption capacity was found to be 7.9745 mg/g, while the maximum decolorization efficiency for the adsorbent was observed to be 99.04%. Adsorption data from the study fitted the Langmuir isotherm with an R 2 value of 0.9815, while the adsorption kinetics followed the pseudo-second-order kinetic model with an R 2 value of 0.9953. The results obtained from the study, therefore showed that the synthesized materials could be used as adsorbents in wastewater treatment.

The Potential of Electrospun Membranes in the Treatment of Textile Wastewater: A Review.

Water security and industrial wastewater treatment are significant global concerns. One of the main issues with environmental contamination has been the discharge of dye wastewater from the textile and dye industries, contributing to an ever-growing problem with water pollution, poisoning water supplies, and harming the ecosystem. The traditional approach to wastewater treatment has been found to be inefficient, and biosorption techniques and mechanisms have been proven to be a successful replacement for conventional methods. Recent developments have led to the recognition of fibrous materials as an environmentally friendly option with broad application in several industries, including wastewater treatment. This review explores the potential of fibrous materials produced by the electrospinning technique as adsorbents for wastewater treatment, while at the same time, for the removal of adsorbates such as oil, dyes, heavy metals, and other substances, as reported in the literature. Textile wastewater filtering structures, produced by electrospinning, are summarized and the use of synthetic and natural polymers for this purpose is discussed. The limitations of electrospun textile wastewater filtering structures are also mentioned. Electrospun nanofibrous membranes appear to be a very promising route to filter textile wastewater and therefore contribute to water reuse and to reducing the contamination of water courses.

Wastewater sludge-derived hydrochar: Effect of operating conditions, activation, and potential use as adsorbent

Scientific management of wastewater sludge generated from biological wastewater treatment is necessary owing to its high moisture content and poor dewaterability. In this investigation, hydrothermal carbonization technique was implemented as a potential solution for wastewater sludge management. To further improve the surface properties of wastewater sludge-derived hydrochar (synthesized at 250 ℃ for 4 h of reaction time), three activation techniques, namely physical, alkali, and alkali followed by acid activation were implemented. The effect of three activation techniques on the properties of hydrochar was investigated using physico-chemical characterization techniques. The sludge-derived hydrochar activated with KOH (1:1 by weight) followed by HCl treatment (1 M) (HC-KA) showcased highly porous structured material having a surface area of 1119 m2 g–1, which was highest amongst the other activation methods chosen in this investigation. Thus, HC-KA was utilized as an adsorbent to evaluate the adsorptive removal of methylene blue (MB). The MB adsorption process followed Langmuir isotherm (R2 of 0.996) with a maximum adsorption capacity of 192.7 mg g–1 and pseudo-second-order reaction kinetics. The results demonstrated that wastewater sludge-derived activated hydrochar can be considered a promising material as an adsorbent in wastewater treatment.

Revealing the interface chemistry of polyaniline grafted biomass via statistical modeling of multi-component dye systems: optimization, kinetics, thermodynamics, and adsorption mechanism.

The growing need to examine the adsorption capabilities of innovative materials in real-world water samples has encouraged a shift from single to multicomponent adsorption systems. In this study, a novel composite, PANI-g-SM was synthesized by covalently grafting a lignocellulosic biomass, Saccharum munja (SM) with polyaniline (PANI). The as-synthesized composite was investigated for the simultaneous adsorption of cationic (Methylene Blue (MB); Crystal Violet (CV)) and anionic dyes (Reactive Red 35 (RR); Fast Green FCF (FG)) from four single components and two binary systems, MB + RR and CV + FG. Further, the effect and interaction of pH (2-11), dosage (0.01-0.04g/10mL), and initial concentration (0.0313 to 0.1563mmol/L) on the elimination of dyes by PANI-g-SM were studied through a novel design of Box-Behnken of Response Surface Methodology (RSM) technique which was found to be highly useful for revealing the chemistry of interfaces in multi-component systems. The extended Langmuir model for the binary system indicated the presence of synergism, as result the maximum monolayer adsorption capacity increased by 44.44%, 645.83%, 67.88%, and 441.07% for MB, RR, CV, and FG dye, respectively. Further, the adsorption process mainly followed a pseudo-second-order kinetic model, and the thermodynamic studies revealed the exothermic nature of adsorption for RR and FG dye while endothermic for MB and CV dye, respectively with varying from - 1.68 to - 6.12kJ/mol indicating the spontaneity of the process. Importantly, the efficacy of the composite was evaluated for the treatment of textile industry effluent highlighting its potential as an adsorbent for wastewater treatment.

Sustainability, performance, and production perspectives of waste-derived functional carbon nanomaterials towards a sustainable environment: A review

The survival of humanity is severely threatened by the massive accumulation of waste in the ecosystem. One plausible solution for the management and upcycling of waste is conversing waste at the molecular level and deriving carbon-based nanomaterial. The field of carbon nanomaterials with distinctive properties, such as exceptionally large surface areas, good thermal and chemical stability, and improved propagation of charge carriers, remains a significant area of research. The study demonstrates recent developments in high-value carbon-based photocatalysts synthesis from various waste precursors, including zoonotic, phytogenic, polyolefinic, electronic, and biomedical, highlighting the progression as photocatalysts and adsorbents for wastewater treatment and water splitting applications. This review highpoints the benefits of using waste as a precursor to support sustainability and circular economy and the risks associated with their use. Finally, we support that a sustainable society will eventually be realized by exploring present obstacles and potential steps for creating superior carbon-based nanomaterials in the future.

The Use of Sawdust at different thickness as low cost adsorbent in wastewater treatment

The Use of Sawdust at different thickness as low cost adsorbent in wastewater treatment

A green cross-linking method for the preparation of renewable three-dimensional graphene sponges for efficient adsorption of Congo red dye

Graphene-based materials possess significant potential for the treatment of dye wastewater due to their exceptional adsorption properties toward stubborn pollutants. However, their utilization is hindered by high preparation costs, low yields, environmental pollution during synthesis, and challenges in regenerating the adsorbent. This study proposes a novel approach to address these limitations by developing nitrogen-doped three-dimensional (3D) polyvinyl alcohol cross-linked graphene sponges (N-PGA) using a cross-linking method with ammonium carbonate. This method offers a relatively mild and environmentally friendly approach. Ammonium carbonate serves as both a reducing and modifying agent, facilitating the formation of the intrinsic structure of N-PGA and acting as a nitrogen source. Meanwhile, polyvinyl alcohol (PVA) is utilized as the cross-linking agent. The results demonstrate that N-PGA exhibits a favorable internal 3D hierarchical porous structure and possesses robust mechanical properties. The measured specific surface area (BET) of N-PGA was as high as 406.538 m2·g–1, which was favorable for its efficient adsorption of Congo red dye molecules. At an initial concentration of 50 mg·L–1, N-PGA achieved an impressive removal rate of 89.6% and an adsorption capacity of 112 mg·g–1 for Congo red (CR) dye. Furthermore, it retained 79% of its initial adsorption capacity after 10 cycles, demonstrating excellent regeneration performance. In summary, the synthesized N-PGA displays remarkable efficacy in the adsorption of CR dye in wastewater, opening up new possibilities for utilizing 3D porous graphene nanomaterials as efficient adsorbents in wastewater treatment.

Enhanced methylene blue adsorption by double alkali activation of highly porous glass microspheres prepared from waste glass

The remediation of water from organic pollutants, such as dyes and related compounds and the reuse of discarded glasses, represents fundamental challenges in highly industrialized countries. Porous glass microspheres have been proposed as efficient adsorbents in wastewater treatment, but their real application is problematic, especially from the perspective of their reuse and recycling. For the first time, the present paper describes the process of preparation and use of highly porous bodies with a specific surface area of nearly 20 m2/g fabricated from alkali activated glass microspheres and applicable for the removal of methylene blue as a model organic dye from wastewater. Alkali activation is applied both as an intermediate step (using 9 M KOH) for the conversion of waste glass into porous microspheres by flame spheroidization process, and as a final step (using 2.5 M NaOH), facilitating low temperature consolidation of the microspheres, and their transformation into porous structures. The experimental adsorption capacity of porous glass microspheres pellet was 122 mg/g. The high correlation coefficient indicates the applicability of Langmuir isotherm adsorption model.

Sustainable oil palm trunk fibre based activated carbon for the adsorption of methylene blue

Activated carbon (AC) is becoming the limelight due to its widespread application as an adsorbent for wastewater treatment, gases, and catalysis. However, its high consumption and price have drawn more attention to the sustainable use of natural resources as precursor for AC production. This study focuses on synthesising AC from two types of oil palm trunk (OPT) fibres, a significant agricultural waste products produced by Malaysia's thriving palm oil industries. The BET surface area of about 2057.9 m2 g−1 was achieved by chemical activation with phosphoric acid (H3PO4). The efficiency of the synthesised AC was critically analysed based on the adsorption experiments with methylene blue (MB) by varying several parameters (dosage of adsorbent, pH, initial dye concentration, and temperature of the solution) to elucidate the adsorption mechanism(s). A maximum adsorption capacity of 320.4 mg g−1 at 50 °C was achieved, and the Temkin (r2 = 0.98, 0.95, 0.95) and Langmuir (r2 = 0.94, 0.93, 0.95) isotherm models fitted the adsorption process better than the Freundlich (r2 = 0.95, 0.90, 0.86) model. Besides, the pseudo-second-order model (r2 > 0.90) best described the adsorption process, favouring chemisorption over physisorption. Thermodynamics showed MB adsorption on AC was spontaneous except at the highest dye concentration. It was exothermic at lower dye concentrations (50 and 100 mg L−1) and endothermic at higher ones (300, 500, and 700 mg L−1). In a nutshell, this study reveals that OPT fibre is a promising precursor for synthesising highly porous AC for the adsorption of MB dye.

Nanostructured Cellulose-Based Aerogels: Influence of Chemical/Mechanical Cascade Processes on Quality Index for Benchmarking Dye Pollutant Adsorbents in Wastewater Treatment.

(1) Background: Nanostructured cellulose has emerged as an efficient bio-adsorbent aerogel material, offering biocompatibility and renewable sourcing advantages. This study focuses on isolating (ligno)cellulose nanofibers ((L)CNFs) from barley straw and producing aerogels to develop sustainable and highly efficient decontamination systems. (2) Methods: (Ligno)cellulose pulp has been isolated from barley straw through a pulping process, and was subsequently deconstructed into nanofibers employing various pre-treatment methods (TEMPO-mediated oxidation process or PFI beater mechanical treatment) followed by the high-pressure homogenization (HPH) process. (3) Results: The aerogels made by (L)CNFs, with a higher crystallinity degree, larger aspect ratio, lower shrinkage rate, and higher Young's modulus than cellulose aerogels, successfully adsorb and remove organic dye pollutants from wastewater. (L)CNF-based aerogels, with a quality index (determined using four characterization parameters) above 70%, exhibited outstanding contaminant removal capacity over 80%. The high specific surface area of nanocellulose isolated using the TEMPO oxidation process significantly enhanced the affinity and interactions between hydroxyl and carboxyl groups of nanofibers and cationic groups of contaminants. The efficacy in adsorbing cationic dyes in wastewater onto the aerogels was verified by the Langmuir adsorption isotherm model. (4) Conclusions: This study offers insights into designing and applying advanced (L)CNF-based aerogels as efficient wastewater decontamination and environmental remediation platforms.

Progress in agricultural waste derived biochar as adsorbents for wastewater treatment

The wastewater generated from diverse human activities needs to be treated, restore, and reused. Researchers have moved from the deployment of synthetic absorbents to manufacturing adsorbents from waste biomass for the elimination of contaminants from wastewater. The deployment of biochar constructed from agricultural waste has elicited significant devotion due to its ready availability, accessibility, low cost, ease of preparation, and environmental sustainability. This review presents developments in the utilization of biochar obtained from agricultural waste for the remediation of domestic wastewater, industrial wastewater, agricultural wastewater, and stormwater. Discussions on the classification, composition, and characteristics of agricultural waste, techniques for biochar production, and characteristics of wastewater as well as the outcomes of the deployment of biochar in the decontamination of wastewater were highlighted. The study concludes that, notwithstanding the identified environmental, social, economic, and infrastructural challenges, biochar constructed from agricultural waste is an effective, efficient, easy to use, and eco-friendly adsorbent for the decontamination of wastewater. Agricultural waste-derived biochar removes contaminants from wastewater and safeguards aquatic ecosystem and contributes to availability of safe water. Future research directions on innovative and more effective avenues for the application of biochar developed from agricultural waste for wastewater treatment are suggested. The outcome of this review will stimulate renewed interests in using readily available and eco-friendly materials in wastewater remediation.

Sorption of Pb2+, Zn2+, Cu2+ and Ni2+ Ions on Na-enriched Natural Zeolite for Wastewater Treatment Process: A Kinetic Approach

Low-cost and easily available natural zeolite is a promising adsorbent for metal ions removal in wastewater treatment. The possibility of using zeolitic tuff from Serbia in the form of Na-enriched natural zeolite (Na-Z) for the adsorption of Pb2+, Zn2+, Cu2+, and Ni2+ ions from wastewater was investigated in the presented paper. The research included Na-Z characterization and determination of adsorption kinetics in individual ion adsorption tests using non-linear pseudo-first-order (PFO), pseudo-second-order (PSO) and mixed-order (MO) kinetic models. The results indicate that the adsorption processes of metal ions on Na-Z are complex processes dominated by multiple rate-limiting mechanisms and best defined by the MO model. The mechanisms of ion diffusion and adsorption to active sites are equally represented in the Pb2+ ions adsorption process. The mechanism of ion diffusion is more pronounced in the Zn2+ ions adsorption process, while in the case of the adsorption of Cu2+ and Ni2+ ions adsorption on the active sites is the main kinetic mechanism. Within the MO model, the PFO rate (external/internal diffusion) and the PSO rate (adsorption on the active sites) were calculated and results were applied to a multicomponent wastewater sample in order to determine and explain the adsorption efficiency in wastewater treatment. The results show that the rate of adsorption of individual metal ions and the efficiency of ion removal from a multicomponent wastewater sample are influenced by several factors including the radius of the hydrated ion and the free energy of hydration. The achieved removal of metal ions by Na-Z is Pb2+ (89%) > Cu2+ (72%) > Zn2+ (61%) > Ni2+ (58%) and defines Na-enriched natural zeolite as an effective adsorbent in wastewater treatment.

Activated Carbon and P-Rich Fertilizer Production from Industrial Sludge by Application of an Integrated Thermo-Chemical Treatment

The cost and environmental impact of sludge disposal methods highlight the necessity of new solutions for resource recovery. This study aims at concurrently producing activated carbon while recovering phosphorous by applying an integrated thermo-chemical treatment to a sludge of industrial origin. The sludge was first subjected to slow pyrolysis on a laboratory scale at different temperatures, and the produced chars were processed by leaching to obtain biocoal. Leaching tests enabled us to define the optimal slow pyrolysis temperatures to maximize leaching performances. Then, sludge was processed in a slow pyrolysis pilot-scale plant, and the produced char was subjected to acid leaching and finally to physical activation. Chemical precipitation was then applied to the liquid leachate to recover phosphorous as a salt. Laboratory-scale slow pyrolysis and leaching tests showed that a higher pyrolysis temperature leads to a lower degree of demineralization by leaching. Leaching enabled us to reduce the char ash content by almost 88%, extracting 100% P, Mg, Ca, and Fe and almost 90% Al. Physical activation of biocoal with CO2 at 700 and 800 °C produced materials with a surface area of 353 and 417 m2 g−1, respectively, that make them potentially applicable as adsorbents in wastewater treatment or in industrial emissions processes. Moreover, the activated carbons showed the atomic H/C and O/C ratios of anthracite, which opens a wide range of alternative market applications to fossil coal, such as metallurgy and the advanced material sector. In addition, the high P and K concentrations in the salt obtained by precipitation make it a promising fertilizing product in line with the current regulations.

From Waste to Resource: Valorization of Lignocellulosic Agri-Food Residues through Engineered Hydrochar and Biochar for Environmental and Clean Energy Applications-A Comprehensive Review.

Agri-food residues or by-products have increased their contribution to the global tally of unsustainably generated waste. These residues, characterized by their inherent physicochemical properties and rich in lignocellulosic composition, are progressively being recognized as valuable products that align with the principles of zero waste and circular economy advocated for by different government entities. Consequently, they are utilized as raw materials in other industrial sectors, such as the notable case of environmental remediation. This review highlights the substantial potential of thermochemical valorized agri-food residues, transformed into biochar and hydrochar, as versatile adsorbents in wastewater treatment and as promising alternatives in various environmental and energy-related applications. These materials, with their enhanced properties achieved through tailored engineering techniques, offer competent solutions with cost-effective and satisfactory results in applications in various environmental contexts such as removing pollutants from wastewater or green energy generation. This sustainable approach not only addresses environmental concerns but also paves the way for a more eco-friendly and resource-efficient future, making it an exciting prospect for diverse applications.

PAN/PVP/CD-MOF composite beads for the removal of Crystal Violet and Brilliant Blue G in water

Cyclodextrin metal–organic frameworks (CD-MOFs) have a high surface area and unique coordination chemistry that enable them to be used as a carrier material for various materials. However, it is unstable in water, limiting its application in aqueous solutions. Here, we report the application of CD-MOFs in treating cationic and anionic dyes in water for the first time by forming a composite with polyacrylonitrile (PAN) and polyvinylpyrrolidone (PVP) to form composite beads. The composition of the composite beads was optimized through a Box-Behnken design of experiments. The optimum composition of PAN = 5.91 wt%, PVP = 1.89 wt%, and CD-MOF = 2.68 wt% yielded a CV and BB sorption capacities of 50.8109 ± 0.0634 mg/g and 28.5583 ± 0.1296 mg/g, respectively. The composite beads were characterized using SEM, EDX, and FTIR. We showed that CD-MOFs could be used as an adsorbent for wastewater treatment.

Hemicelluloses hydrogel: Synthesis, characterization, and application in dye removal

Novel materials using biowaste as adsorbents in wastewater treatment have been allocated considerable interest. Herein, we present the synthesis of different hydrogels of crosslinked polyacrylamide in presence of hemicelluloses with/ without bentonite, using a soft reaction condition. The structure of new hydrogels was characterized by spectroscopic, thermal and microscopic experiments. The semi-interpenetrated network with hemicelluloses: 10 %; acrylamide 79 %; bentonite 10 %; N,N,N′,N′-tetramethylethylenediamine: 1 % allows reducing 20 % the use of non-renewable acrylamide, without changing its decomposition temperatures and keeping its water absorption capacity. This hydrogel was applied to dye removals, such as rhodamine B, methylene red and methylene blue in aqueous solutions. In the case of methylene blue, highest removal is observed with maximum adsorption of qmax = 140.66 mg/g, compared to material without hemicelluloses that only a qmax = 88.495 mg/g. The adsorption kinetics and equilibrium adsorption isotherms are in accordance with the pseudo-second-order kinetic model and Langmuir isotherm model, respectively. The developed hydrogel from hemicelluloses represents a potential alternative adsorbent for a sustainable system of sewage treatment.

The Use of sawdust and sugarcane bagasse as low cost adsorbent in wastewater treatment

The Use of sawdust and sugarcane bagasse as low cost adsorbent in wastewater treatment

Fabrication of porous adsorbent by quinoa husk stabilized foam templates for dye adsorption and carbonization for soil remediation

In this study, a novel adsorbent with a sufficient porous structure was fabricated using a green and highly stable water-based foam template. This template was stabilized with agricultural waste quinoa husk (QH) and applied to remove dye pollutants in wastewater. The porous adsorbent exhibited a high adsorption capacity of 740.95 mg/g for methylene blue and 1022.1 mg/g for methyl violet. The adsorption process was well described by the Langmuir-Freundlich model and the pseudo second-order kinetic model. A sustainable concept for handling the spent adsorbent was also proposed, involving its conversion into biochar and safe return to the soil. An additional benefit was observed, as the biochar effectively adjusted the physicochemical properties of the soil and improved crop growth with the addition of 1 wt%. The potential application of porous adsorbent in wastewater treatment and the reference of sustainable strategy for disposing of other adsorbents are both noteworthy.