Adsorbent For Removal Of Methylene Blue Dye Research Articles

Optimization study of methylene blue dye adsorption on Chamaerops humilis fibers biosorption using a central composite design

This research explores the effectiveness of Chamaerops humilis (CH) fibers as a biosorbent for the adsorption of Methylene Blue (MB) dye from aqueous solutions. The fibers were characterized using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR). To optimize the dye removal process, a Design of Experiments methodology, specifically Central Composite Design (CCD), was applied. Factors such as solution pH, adsorbent dosage, contact time, and temperature were varied. The CCD analysis identified the optimal conditions for maximum removal efficiency (99.87 %) of a 10 mg/L MB solution, which were: 1.06 g/L of CH fiber dosage, pH 9.6, and a contact time of 60 min. The adsorption process aligned well with a pseudo-second-order kinetic model, and the maximum adsorption capacity of CH fibers was determined to be 9.422 mg/g. Thermodynamic parameters, including Gibbs free energy (ΔG°), enthalpy (ΔH°), and entropy (ΔS°) changes, were calculated, confirming that the adsorption is spontaneous and endothermic. The study highlights the potential of Chamaerops humilis fibers as an efficient and eco-friendly adsorbent for MB dye removal, offering a sustainable and cost-effective solution for wastewater treatment, particularly in industrial effluent management.

Melamine-Maleic Acid Polyamide Adduct / Polyacrylonitrile Nanofibers as a Novel Adsorbent for Removal of Methyelene Blue Dye from Aqueous Solutions

Efficient removal of methylene blue (MB) dye from aqueous solutions is crucial for addressing environmental pollution. This study investigates the potential of Melamine-maleic acid polyamide adduct/polyacrylonitrile (ME-MA amide polymer/PAN) nanofibers as a novel adsorbent for MB dye removal. Characterization via scanning electron microscopy (SEM) revealed surface morphology changes, with fiber diameters ranging from 1 to 3 μm. Thermal stability analysis demonstrated enhanced stability for ME-MA/PAN compared to pure PAN fibers. Fourier transform infrared (FT-IR) analysis confirmed the presence of hydroxyl, amide, and thiol groups on the nanoparticle surface, covalently attached to the nanofiber surface. Through electrospinning, ME-MA/PAN composites were synthesized, showing promising capabilities for dye removal. Optimal conditions were observed at pH 12 and a ME-MA PAN dose of 0.02 g. MB removal efficiency increased with higher initial dye concentrations, peaking at 30 mg/L, and higher temperatures up to 40°C. Adsorption isotherm models indicated Langmuir adsorption capacity (Qm) of 111.10 mg g−1 and a separation factor (RL) of 0.297, with Freundlich constants (1/n) and KF values of 0.418 and 22.9, respectively. Kinetic and thermodynamic studies revealed favorable conditions for MB dye removal, validating ME-MA amide polymer/PAN nanofiber composites as environmentally friendly and effective materials for eliminating toxic MB dye from aqueous solutions. This research highlights the potential of ME-MA/PAN nanofibers in addressing dye pollution, suggesting their application in wastewater treatment for sustainable environmental management. Further investigation into regeneration methods and scalability is recommended for practical implementation in real-world scenarios.

Preparation of Palm Oil Industry’s Biomass-Based Graphene Composite for the Adsorptive Removal of Methylene Blue

The ability of POME-based graphene shell composite (P-GSC), an adsorbent generated from oil palm wastes abundantly available in Malaysia such as POME and PKS, was examined in removing methylene blue (MB) dye by adsorption. Adsorption experiments, involving a batch column study and a batch equilibrium study, were conducted to investigate the efficiency of synthesized P-GSC from PKS as a base material in the removal of MB dye. The batch column study demonstrated that small-sized synthesized P-GSC from PKS as a base material could remove up to 98.5% for concentration. Therefore, the following batch equilibrium study was carried out on small-sized P-GSC only. Adsorption isotherms and kinetic isotherms were studied, from which the experimental data showed that the adsorption exhibited a good fit with the Freundlich model ([Formula: see text]) and followed the pseudo-second order model ([Formula: see text]). FESEM, XPS, and XRD morphological and elemental analysis indicated the successful graphinization of POME on the P-GSC surface. The concept of deploying POME as the carbonaceous source to produce P-GSC, and then, deploying the resultant P-GSC as the adsorbent for MB dye removal has presented promising practical potential. Such cost-effective and environmentally friendly reuse of waste materials is envisioned to promote a ‘zero-waste industry.’

Fabrication of semi-interpenetrated PVA/PAMPS hydrogel as a reusable adsorbent for cationic methylene blue dye: isotherms, kinetics and thermodynamics studies

A reusable adsorbent was developed based on semi-interpenetrated hydrogel made of poly(vinyl alcohol) (PVA) and poly(2-acrylamido-2-methylpropane sulfonic acid) (PAMPS) for the adsorptive removal of cationic methylene blue (MB) dye. The developed PVA/PAMPS adsorbent hydrogel was characterized using Fourier transform infrared spectroscopy (FTIR), thermogravimetric analyzer (TGA) and scanning electron microscope (SEM) analysis tools. Consequence of the variation of AMPS concentration on water uptake profile and polymer add-on (%) was explored. In addition, batch adsorption studies were performed to evaluate the aptitude of the developed adsorbent for MB dye removal under several adsorption conditions. The results showed an increase in the add-on (%) value up to 70% with increasing AMPS content up to 5%. Moreover, the MB dye removal was occurred quickly at the initial stage and recorded 60% after only 5 min from the initial contact time, while it recorded a maximum value of 86% at 25 oC. The experimental adsorption data were well-fitted to the Langmuir isotherm model and followed the pseudo-second-order kinetic model. Moreover, the adsorption of MB dye by the adsorbent hydrogel was an endothermic process. Besides, the PVA/PAMPS adsorbent exhibited better reusability with a maximum removal (%) exceeded 70% after five consecutive cycles. The results obtained from this study infer that the PVA/PAMPS adsorbent hydrogel could be effectually used as an appropriate and reusable adsorbent for removing cationic MB dye molecules from wastewater bodies.

Facile fabrication of silk fibroin microparticles: their characterization and potential adsorption study

Silk fibroin (SF) microparticles were fabricated by blending of SF solution with hydroxyl propyl methyl cellulose (HPMC), and the SF/HPMC blend films were prepared using simple solvent evaporation technique. The SF/HPMC blends were dissolved in ultrapure water, and SF microparticles were generated with and without sonication. Fourier transformation infrared spectroscopy (FTIR), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA)/derivative thermogravimetric (DTG) measurements were used for the characterization of blend films and microparticles. The microparticles obtained sonicated consist of nanosized pores on the surface. The size of the pores was nano, but the diameter of particles was around 10 µm. Further, SF microparticles were evaluated as a novel biosorbent for the methylene blue (MB), a cationic dye. The influential factors (pH, contact time) to the adsorption of the dye by the microparticles were investigated. The SF microparticles showed a very good adsorption capacity of about 490 (nonsonicated) and of about 512 (sonicated) mg/g of the dye without any surfactants. The adsorption kinetics validates the practicality of using the pseudo-second-order kinetics. Langmuir and Freundlich isothermal models were used, and the results showed that the adsorption behavior of the samples best fits (R2=0.998) the Langmuir model. The easy preparation and obtained results suggest that the SF microparticles can be used as effective adsorbent for MB dye removal.

A sustainable process for adsorptive removal of methylene blue onto a food grade mucilage: kinetics, thermodynamics, and equilibrium evaluation

Adsorption of dyes onto natural materials like polysaccharides is considered a green chemistry approach for remediation of wastewater. In this work, the polysaccharide isolated from the corm of Colocasia esculenta (L.) Schott or taro tuber (CEM) was utilized for removing methylene blue (MB) from aqueous solution by batch adsorption method. The CEM adsorbent was characterized by FTIR spectroscopy, Brunauer–Emmett–Teller (BET), and scanning electron microscopy (SEM). The solution pH and adsorbent dose have been found to have a significant positive correlation with the adsorptive removal efficiency of CEM for MB dye. The removal efficiency of CEM was found to be 72.35% under the optimum conditions; 20 mg/L initial concentration of dye, 120 mg of adsorbent dose, solution pH 8.5, 311.2 K temperature and 80 min contact time. The adsorption of MB onto CEM followed best the Freundlich isotherm and pseudo-second-order kinetics. The adsorption was thermodynamically favorable and was endothermic in nature. The desorption/adsorption data justifiably indicated the reuse capability of CEM adsorbent for MB adsorption. Hence, CEM may be regarded as an eco-friendly and cost-effective natural adsorbent for MB dye removal from aqueous solution.