Adsorbent Dosage Research Articles

Preparation and characterization of oat hulls-filled-sodium alginate biocomposite microbeads for the effective adsorption of toxic methylene blue dye

In this work, the performance of oat hull-filled sodium alginate (SA-O) biocomposite microbeads in the adsorptive removal of methylene blue (MB) dye was examined. First, oat hulls were pulverized and biocomposite gels containing different weight ratios of oat hulls (10 %, 20 %, and 30 %, concerning the SA amount) were prepared by dispersing them in SA solution by ultrasonic homogenization method. Finally, gels were cross-linked by dropping into a 2 % CaCl2 solution. The study revealed that the optimal adsorbent dosage was 0.025 g/50 mL, pH was roughly 6–8, and the contact time was 120 min. According to isotherm models, the non-linear Sips and Langmuir model was more appropriate compare to other isotherms from error analysis, with a maximum adsorption capacity of 687.65 mg/g and 757.57 mg/g at 298 K, respectively. Furthermore, the non-linear kinetic data and error analyzes demonstrated that the process followed the pseudo-second-order kinetic. The adsorption process was exothermic (∆H°=−17.71 kJ/mol) and spontaneous (∆G°=−26.23 kJ/mol) at 298 K, based on thermodynamic characteristics. Furthermore, reusability investigations demonstrated that the adsorbent retained its performance with no major changes in characteristics. This work reveals that highly efficient, low-cost, sustainable, and eco-friendly SA-O composites with properties might be useful adsorbents for cationic dye adsorption.

Investigation of the iridium adsorption process with functionalized magnetic nanoparticles using triisobutylphosphine sulfide extractors

In this research work, the adsorption process of iridium using magnetic nanoparticles functionalized with Cyanex 471X has been investigated. In this regard, parameters affecting the adsorption process such as pH, initial concentration of iridium ions, contact time and adsorbent dosage were assessed. According to the results, pH 6, adsorbent dosage 1.2 g/L, initial concentration of iridium of 10 mg/L, and contact time of 10 min were selected as optimal conditions for iridium adsorption by this synthesized magnetic nanosorbent. The kinetics of the adsorption process was studied, and it was found that the adsorption reaction follows the pseudo-second-order kinetic model with the correlation coefficient of 0.9960. Also, experimental studies indicated that the Langmuir adsorption isotherm model best matches the experimental data (R2 = 0.9961). The maximum adsorption capacity of the nanosorbent for iridium adsorption was estimated to be 35.34 mg/g by the Langmuir isotherm. With the thermodynamic analysis of the adsorption process, it was found that this process is endothermic and spontaneous. In addition, in the investigation of iridium adsorption and desorption, HCl/HNO3 solution with a concentration of 1.5 M was selected as suitable eluent.

Utilising date palm fibres as a permeable reactive barrier to remove methylene blue dye from groundwater: a batch and continuous adsorption study.

This study aimed to utilise cheap and abundantly available date palm fibre (DPF) wastes for the remediation of methylene blue (MLB) dye-contaminated groundwater. The DPF adsorbents were first prepared, followed by various characterisation analyses, including surface morphology, functional groups, and material structure. Subsequently, the DPF adsorbents were applied in the batch and continuous adsorption studies to assess the MLB dye removal from aqueous environments. The batch adsorption study achieved 98% maximum removal efficiency with a contact time, adsorbents dosage, initial pH, temperature, particle size, initial dye concentration, and agitation speed of 105min, 3g/L, 7.0, 45°C, 0.075mm, 50mg/L, and 150rpm, respectively. Langmuir was the best-fitted isotherm model depending on a higher correlation coefficient (R2 = 0.985), with a maximum monolayer dye adsorption capacity (qmax) of 54.204mg/g. Additionally, the second order was the best-fitted kinetic model (R2 = 0.990), indicating that MLB dye was removed through chemisorption. Besides, the positive enthalpy change (ΔH°) and negative Gibb's free energy (ΔG°) values verified the endothermic process and spontaneous adsorption. According to the impact analysis of initial dye concentrations and flow rates on the permeable reactive barrier (PRB) performance in the continuous adsorption study using the Thomas, Belter, and Yan models, the experimental results and predicted breakthrough curves reflected an excellent agreement (R2 ≥ 0.8767) and a sum of squared errors (SSE) ≤ 0.4834. In short, the results demonstrated DPF as an effective adsorbent material in PRB technology.

Optimization, Kinetic and Thermodynamic Study of Rhodamine B Removal by Zinc Chloride-activated Arachis hypogaea (Groundnut Husk) biochar

Adsorption of dye from industrial effluent before discharge into the environment has become a major challenge to the food, pharmaceutical, textile, photographic and cosmetic industries. This has led scientists to the search for suitable green solutions. Carbonized and zinc chloride activated Arachis hypogaea (groundnut husk) in a 1:1 ratio was used as an adsorbent for the removal of Rhodamine B from aqueous solution. The adsorbent was characterized by ash content, bulk density, moisture content, pH, Iodine number, surface area and functional group analyses. Key parameters such as initial pH, initial concentration of Rhodamine B dye, temperature and contact time were investigated. The equilibrium data obtained were correlated with Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherms. It was found that both the Freundlich and Langmuir isotherms fit well to the data. The Langmuir isotherm model best describes the uptake of Rhodamine B onto zinc chloride activated groundnut husk biochar with R2 > 0.997. Maximum Rhodamine B. dye removal was observed at a pH of 11.0, with an adsorbent dosage of 1.0 g, a contact time of 125 min, an initial dye concentration of 20 mg/L and a temperature at 315 K. The efficiency of zinc chloride activated groundnut husk biochar for Rhodamine B removal was 99.55% for dilute solutions at 50 g/L. The Fourier Transform Infrared (FTIR) spectra recorded before and after activation showed the numbers of functional groups available for Rhodamine B. molecules to bind onto in the studied adsorbent. The kinetic data were best described by the pseudo-first-order and pseudo second-order models, while the thermodynamic studies indicated a spontaneous and endothermic nature in the adsorption of Rhodamine B by the zinc chloride modified groundnut husk. This research clearly details an innovative approach to utilizing carbonized and zinc chloride-activated Arachis hypogaea (groundnut husk) as an eco-friendly adsorbent for the removal of Rhodamine B from industrial effluents.

Isotherm, kinetic, and thermodynamic studies of adsorption of copper (II) and nickel (II) ions using low‐cost treated orange peel from aqueous solutions

AbstractThe aim of this study was to utilize processed orange peel waste (TOP) as an adsorbent to remove Cu(II) and Ni(II) ions from aqueous solutions. As a result of systematic experiments to determine the optimal conditions, it was determined that the most suitable conditions for the effective removal of Cu(II) ions were 400 mg/L initial concentration, 100 min contact time, 0.2 g adsorbent dosage, and a solution pH of 5.92. Similarly, the optimal conditions for the removal of Ni(II) ions were determined by systematic experiments to be 300 mg/L initial concentration, 0.2 g adsorbent dosage, 100 min contact time, and a solution pH of 6.19. The systematic experiments also included further investigation of the surface properties of TOP, and promising results were obtained by tests at three different temperatures (298, 308, and 318 K). The adsorption capacities for Cu(II), Ni(II), and Ni(II) were determined as 72.99, 75.18, and 76.33 mg/g, 42.55, 44.44, and 46.29 mg/g, respectively. Further analysis of the adsorption kinetics revealed that the pseudo‐second‐order model accurately represented the experimental data for both ions. Thermodynamic investigations provided strong evidence that the adsorption process of these noble metal ions on TOP is endothermic and spontaneous. The results of this study emphasize that TOP, with its low cost, easy‐to‐use nature, and high adsorption capacity, can be considered a long‐term solution for environmental remediation and water treatment in sustainable engineering applications.

Construction and demolition waste as a low-cost adsorbent for water treatment: kinetics, isotherm, thermodynamics, and Fenton regeneration.

The present study proposes to investigate the feasibility of using construction and demolition waste (CDW) as an aqueous remediation agent through adsorption. The CDW, with and without chemical and thermal pre-activation, was evaluated to remove the methylene blue (MB) dye from the water solution. Variables interfering with adsorption processes, such as adsorbent dosage, solution pH, and particle size, were evaluated. The material was characterized by pHZPC, FTIR, XRD, SEM, EDS, and TG. The kinetic and equilibrium data better fitted the Elovich and Sips models, respectively. A maximum adsorption capacity of 18.62mgg-1 at 60°C was observed. Thermodynamic data indicated that adsorption occurred through a spontaneous and favorable process governed mainly by physical processes. The regeneration studies were carried out using processes based on the Fenton reaction, where the catalytic action of the iron naturally present in the CDW was evaluated. The results showed that the desorption balance was the main limiting factor for the effective regeneration of the saturated material. Adding Fe2+ to the system made this process suitable for the regeneration of the CDW and degradation of the pollutant in the aqueous phase. A regeneration efficiency of 65%, maintained practically constant during five adsorption-regeneration cycles, was observed. These results highlight the high potential of using CDWs as an adsorbent material.

Innovative Use of Spirogyra sp. Biomass for the Sustainable Adsorption of Aflatoxin B1 and Ochratoxin A in Aqueous Solutions

This research investigates the efficacy of Spirogyra sp. biomass as an effective adsorbent for the removal of AFB1 and OTA from aqueous solutions. Several factors, including contact time, adsorbent dosage, pH level, and initial mycotoxin concentration, were analyzed to evaluate their impact on adsorption efficacy. The optimal contact time for equilibrium was determined at 60 min, during which the TPA obtained a 91% reduction in AFB1 and 68% removal of OTA. Although increasing the adsorbent dosage improved effectiveness, excessive quantities led to particle aggregation, hence diminishing adsorption performance. The optimal dosage of 5.0 mg/mL optimized the efficacy and use of resources. Adsorption was more efficacious at acidic to neutral pH levels (5–6), enhancing the accessibility of functional groups on the biomass. Kinetic analysis indicated that adsorption process followed a pseudo second-order model, whereas isotherm studies demonstrated a heterogeneous adsorption mechanism, with the Freundlich model providing the optimal fit. The TPB exhibited enhanced adsorption capacities for both mycotoxins, offering a viable solution for mitigating mycotoxin contamination in food and feed. These findings illustrate the significance of biomass treatment techniques in improving mycotoxin removal efficacy and suggest the potential of algal biomass in food safety applications.

Adsorption of Phosphate from Aqueous Solution Using Hydrochar Produced from Agricultural Wastes

Excess phosphorus (P) in agricultural runoff can cause eutrophication in nearby waterbodies. Therefore, it is crucial to remove P from agricultural runoff before it reaches aquatic environments. This study evaluated the P adsorption potential of adsorbents prepared via co-hydrothermal carbonization of multiple agricultural wastes, including dairy manure (DM), corn stover (CS), and eggshell (ES), followed by thermal activation. The performance of the prepared adsorbents was investigated by both batch and column experiments. The activated hydrochar (AHC) with a DM/CS/ES ratio of 1:0:1 showed the highest P adsorption capacity of 209 ± 0.6 and 65.97 ± 9.04 mg/g in batch and column experiments, respectively. The P adsorption mechanism was well described by the Langmuir isotherm model (R2 > 0.8802) and the pseudo-second-order kinetics model (R2 > 0.8989). The adsorbent indicated the longest breakthrough and exhaust time of 210 and 540 min, respectively, with an adsorbent dose of 1 g and an initial concentration of 25 mg P/L. The breakthrough curve was well described by the Thomas model (R2 > 0.971). Thus, this study indicates that AHC with eggshell has high potential for use as an adsorbent for P removal from agricultural runoff.

Removal of metaldehyde and acetamiprid by extracted cellulose from biomass incorporated with copper after acetylation

The presence of pesticides in water have reached to an alarming level in some parts of the world and have caused deteriorating effects on human health. Reclamation of portable water from such contaminants have become mandatory. Scientists around the world are trying to devise new methods of water purification. The target can be achieved either by limiting the use of pesticides for agriculture purposes or by devising unique methods for their recoveries from contaminated water. In this context, herein cellulose has been extracted from Populus nigra, subjected to acetylation using acetic acid in the acidic medium (sulfuric acid). The modified acetylated cellulose was treated with Cu-based salt to enable the metallic combination. The prepared sorbent was characterized by UV, SEM, EDX, XRD, and FTIR techniques. Two insecticides; metaldehyde and acetamiprid in synthetic waste-water solution were subjected for adsorption on the modified sorbent in a series of experiments to evaluate the impact of contact time, sorbent dosage, pH, and temperature. Optimum conditions established in a series of experiments such as 80 and 60 min of contact time for acetamiprid and metaldehyde respectively, pH of 8 and 9 (slightly basic) correspondingly for the mentioned pesticides, and a 0.08 g adsorbent dosage were used in the estimation of kinetics and isothermal parameters. The kinetic data successfully followed the pseudo-second-order kinetic model whereas, the isothermal data was found to be best fitted by Langmuir isotherm model in the case of acetamiprid and by Freundlich in the case of metaldehyde. The regeneration study was performed for both the pesticides showing more than 70 % removal capabilities of fabricated adsorbent after three consecutive cycles. The prepared adsorbent could be a better alternative of commercial activated carbon however, further experiments are encouraged to investigate the full environmental application spectrum of the fabricated sorbent.

Efficient removal of paracetamol, diclofenac sodium, and tetracycline using green synthesized Fe-zn co-doped sunflower seed shells

ABSTRACT In this study, carbon material obtained from sunflower seed shells and doped with Fe and Zn using mint extract (Fe-Zn-SSSC) was prepared, and the usability of this adsorbent in the removal of paracetamol, diclofenac sodium, and tetracycline was investigated. Fe-Zn-SSSC was characterized by SEM-EDX and FTIR. Additionally, the effects of pH and adsorbent dosage on the removal of paracetamol, diclofenac sodium, and tetracycline were investigated. The removal rates of paracetamol, diclofenac sodium, and tetracycline were obtained as 88.7%, 65.4%, and 76.0% at a pH of 4, after 1 hour of adsorption with 5 g/L Fe-Zn-SSSC, respectively. The best removal of paracetamol, diclofenac sodium, and tetracycline was obtained at pH 4, with qmax values calculated as 14.51 mg/g, 6.33 mg/g, and 8.99 mg/g, respectively. It was determined that the adsorption of paracetamol, diclofenac sodium, and tetracycline with Fe-Zn-SSSC was more compatible with the Langmuir isotherm model and pseudo-second-order kinetic model. As a result, this study demonstrates that carbon materials synthesized from sunflower seed shells can serve as an effective and low-cost adsorbent for drug from water.

Arabic gum-grafted-polyaniline@MnFe2O4/UIO66-NH2 bionanocomposite as adsorbent for quercetin antioxidant: Efficiency, kinetics, thermodynamics and isotherm modelling

Quercetin is one of the most powerful antioxidants in nature and a major dietary flavonoid, so its efficient recovery by nanoadsorbents can be valuable for human health. In this study, the nanocomposite Arabic gum-grafted-polyaniline@MnFe2O4/UIO66-NH2 (AG-g-PANI@MnFe2O4/UIO66-NH2) was synthesized by in situ copolymerization. The physicochemical and structural properties of the AG-g-PANI@MnFe2O4/UIO66-NH2 nanocomposite were examined using various methods, including XRD, FE-SEM, FT-IR, EDX, VSM, TGA, and BET. The adsorption capacity of natural nanoadsorbent was evaluated for the adsorption of quercetin antioxidant from an ethanol-water solution (50 % v/v) in a batch system. The influence of controlling factors such as solution pH, adsorbent dose, contact time, initial quercetin concentration and temperature on the adsorption process was investigated. The highest adsorption capacity (9.1157 mg.g−1) was achieved at a pH of 8, with 0.025 g of adsorbent, a quercetin solution concentration of 20 mg.L−1, a 300 min contact time and at the temperature 298.15 K. In addition, the data from adsorption experiments were analyzed using different isotherm and kinetic models. The findings demonstrated that the Temkin isotherm and the pseudo-second-order kinetic model are the most suitable for representing the adsorption behavior. In addition, from analysis of the temperature effect was found that the adsorption of quercetin on AG-g-PANI@MnFe2O4/UIO66-NH2 is a spontaneous (∆G° < 0) and exothermic (ΔH° < 0) process. Finally, the reusability of nanoadsorbent and desorption kinetics of quercetin were investigated and it was specified that AG-g-PANI@MnFe2O4/UIO66-NH2 can be effectively renewed and recycled, maintaining its adsorption efficacy without significant reduction after five repeated cycles.

Adsorption of methyl orange and methylene blue on activated biocarbon derived from birchwood pellets

This study explored the adsorption capacity of a physically activated biocarbon derived from the pyrolysis of birchwood pellets (ABPB) towards two dyes - methyl orange (MO, anionic) and methylene blue (MB, cationic), at pH 2, 7 and 11. Compared to mineral commercial activated carbon (CACmineral), ABPB exhibited lower SSA, pores volume and surface; higher external surface and average pore diameter, similar ash content and aromaticity, and stronger hydrophilicity and polarity. The maximum adsorption capacity on ABPB was equal to 220 mg/g for MO and 91 mg/g for MB after 17 h. Batch tests with variable adsorbent amount (0.5–2.5 g/L) showed for both ABPB and CACmineral better results for lower adsorbent dose. Under all tested conditions, ABPB showed higher or analogous adsorption capacity compared to CACmineral. Based on the pKa of MB (3.80) and MO (3.46) and on the pHPZC of ABPB (5.3), the adsorption was favored at pH 2 for MO and at pH 11 for MB. Kinetics analysis and isotherm modelling revealed that, although many different physicochemical interactions occurred between ABPB and the dyes molecules, chemisorption is the rate-controlling step and prevalent mechanism. In conclusion, this study may provide support to further research aimed at exploring the effect of ABPB's physicochemical properties on the efficiency and mechanisms of dyes adsorption.

Facile Preparation of Cross-Linked Moringa oleifera Seed Hulls Powder/Hydroxyapatite Framework Composite for Efficient Removal of Toluidine Blue and Methyl Violet 2B from Aqueous Solution

AbstractIn this study, adsorption of two cationic dyes, Toluidine Blue (TB) and Methyl violet 2B (MV 2B) from an aqueous solution was achieved by using multifunctional composite material. The formulation of the composite (MO@HA) was obtained by using Moringa oleifera seed hull powder, calcium chloride (CaCl2), and ammonium hydrogenophosphate (NH4)2HPO4 salts. Surface morphology, functional groups, specific surface area, and surface charge of the composite were explored using Scanning electron microscopy (SEM), Fourier Transform infrared spectroscopy (FTIR), BET analysis, and point of zero charge (PZC), respectively. The composite material resulted in a structural change in the surface of the adsorbents, increased oxygen vacancies, enhancement of active sites, and a specific surface area of 735.55 m2 g−1. Different adsorption parameters such as pH, contact time, adsorbent dosage, and initial concentration were evaluated. The adsorption study showed that equilibrium was reached after 60 min, and the optimum adsorption pH for both dyes (TB and MV 2B) was 6. Langmuir, Freundlich, Liu, and Temkin were fitted to describe the adsorption isotherm, both TB and MV 2B had best correlation with Liu isotherm. The maximum adsorption capacity of TB and MV 2B were 341.488 and 182.453 mg g−1, respectively. Adsorption-desorption cycling studies on the adsorbent confirmed its regeneration and reusability after 5 cycles. A possible adsorption mechanism involving electrostatic interactions, n-π bonding, and hydrogen bonding was suggested. These findings highlight a new direction in the development of efficient and sustainable adsorbent in environmental remediation, specifically in the removal of dyes from aqueous solution.

Preparation, characterization and application of polymeric ultra-permeable biodegradable ferromagnetic nanocomposite adsorbent for removal of Cr(VI) from synthetic wastewater: kinetics, isotherms and thermodynamics

Hexavalent chromium (Cr(VI)) contamination in drinking water due to industrial activities is a growing worldwide concern. Cr(VI) concentrations exceeding a few parts per billion (ppb) can cause serious health problems such as asthma, blood cancer, kidney-related diseases, liver and spleen damage, as well as neurological system, immunological deficiencies, and reproductive issues. This study, thus, explored the feasibility of employing a novel polymeric ferromagnetic nanocomposite adsorbent made of low-cost, biodegradable, and ultra-permeable materials from pulp and paper sludge for adsorptive removal of hexavalent chromium (Cr6+) from synthetic wastewater. Vibrating-sample magnetometer (VSM), X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer-Emmet-Teller surface area (BET), and Fourier transform infrared (FTIR) were used to analyze the produced nanocomposite adsorbent. The Fourier transform infrared results confirmed the presence of adsorptive peaks attributed to −OH, −NH2, and FeO. Scanning electron microscopy micrographs revealed a porous adsorbent surface. XRD revealed the existence of the crystalline spinel-structured magnetite (Fe3O4) phase of iron oxide, while the saturation magnetization was established to be 26.90 emu/g. The Brunauer–Emmett–Teller analysis confirmed a slight decrease in the surface area of the nanocomposite adsorbent to 6.693 m2.g−1, compared to Fe3O4 (7.591 m2.g−1). The optimum conditions for Cr6+ removal were pH 2.0, 1.0 g/L adsorbent dose, room temperature (25°C), 120 min contact time, and 20 mg/L pollutant concentration. During removal, the Cr(VI) was adsorbed by electrostatic attraction and/or reduced to trivalent chromium Cr(III). At low starting Cr(VI) concentrations, chemisorption dominated the removal process, but as concentrations increased, physisorption became more significant. The prepared nanocomposite adsorbent presented exceptional removal efficiency of up to 92.23%, indicating that it may be useful for the adsorption of metal ions from industrial and household wastewater.

High-performance activated carbon from coconut shells for dye removal: study of isotherm and thermodynamics.

This study investigates the production of high-performance activated carbon (AC) from coconut shells (CS) through acid and base activation processes, along with pre- and post-functionalization of the biochar, aiming to effectively remove dyes from aqueous solutions. The resulting AC exhibited outstanding adsorption capabilities, with the Langmuir model providing a good fit to the experimental data. Maximum adsorption capacities were observed at different temperatures: 805 mg g-1 at 298 K, 904 mg g-1 at 318 K, and 1000 mg g-1 at 338 K for NaOH-activated AC, and 252 mg g-1 at 298 K, 295 mg g-1 at 318 K, and 305 mg g-1 at 338 K for H2SO4-activated AC. The presence of active sites and functional groups on the surface of AC facilitated dye adsorption. The influence of various parameters, including adsorbent dosage, dye concentration, pH, and temperature, on the adsorption process were also examined, identifying the ideal conditions for dye removal. Thermodynamic analysis confirmed the endothermic nature of the adsorption process, with higher temperatures leading to increased adsorption capacities. Overall, the research highlights the potential of various activation routes for the production of high-value AC as a sustainable and effective adsorbent for dye removal from wastewater.

Enhancing Selenium Removal Using Pre-Treated Natural Clay: Experimental Investigation and Predictive Modeling

Abstract A heat treatment methodology was adopted as a pretreatment strategy, altering the porous structure of the clay to minimize leaching for selenium adsorption in an aqueous system. Rigorous experiments were carried out in batch mode to determine optimal parameters across various variables, including contact time, adsorbent dosages, selenium concentrations, pH, temperature, and stirring speed during selenium removal using natural clay. Investigating several kinetic and isotherm models revealed the best fitting for the pseudo-second-order and the Langmuir isotherm. Endothermic and spontaneous characteristics of the adsorption process were shown during thermodynamic analysis. In this study, a predictive model for the efficiency of selenium separation was established using Response Surface Methodology (RSM). Additionally, an Artificial Neural Network (ANN), a data-driven model, was employed for comparative analysis. The predictive model exhibited a high degree of agreement with experimental data, demonstrated by a low relative error of &lt;0.10, a high regression coefficient of &gt;0.97), and a substantial Willmott-d index of &gt;0.95. Moreover, the efficacy of pre-activated clay in selenium removal was assessed, revealing the superior performance of ANN models over RSM models in forecasting the efficiency of the adsorption process. This research significantly advances an effective and sustainable material for selenium removal, providing valuable insights into predictive modeling techniques applicable to similar contexts to boost scale-up confidence during industrial implementation in affected regions.&amp;#xD;

Recent Developments in the Adsorption of Heavy Metal Ions from Aqueous Solutions Using Various Nanomaterials

Water pollution is caused by heavy metals, minerals, and dyes. It has become a global environmental problem. There are numerous methods for removing different types of pollutants from wastewater. Adsorption is viewed as the most promising and financially viable option. Nanostructured materials are used as effective materials for adsorption techniques to extract metal ions from wastewater. Many types of nanomaterials, such as zero-valent metals, metal oxides, carbon nanomaterials, and magnetic nanocomposites, are used as adsorbents. Magnetic nanocomposites as adsorbents have magnetic properties and abundant active functional groups, and unique nanomaterials endow them with better properties than nonmagnetic materials (classic adsorbents). Nonmagnetic materials (classic adsorbents) typically have limitations such as limited adsorption capacity, adsorbent recovery, poor selective adsorption, and secondary treatment. Magnetic nanocomposites are easy to recover, have strong selectivity and high adsorption capacity, are safe and economical, and have always been a hotspot for research. A large amount of data has been collected in this review, which is based on an extensive study of the synthesis, characterization, and adsorption capacity for the elimination of ions from wastewater and their separation from water. The effects of several experimental parameters on metal ion removal, including contact duration, temperature, adsorbent dose, pH, starting ion concentration, and ionic strength, have also been investigated. In addition, a variety of illustrations are used to describe the various adsorption kinetics and adsorption isotherm models, providing insight into the adsorption process.

Sulfonate-Bonded Conjugated Microporous Polymer Hollowed-Out Spheres to Capture Fluoroquinolone Antibiotics and Cationic Dyes from Wastewater.

Developing adsorbent materials for the efficient removal of multiple organic pollutants in water is of importance technological significance. In the present work, a kind of conjugated microporous polymer (CMP) with a hollow sphere structure was constructed by applying SiO2 nanoparticles as a template and 1,3,5-triethynylbenzene (TEB) and 2,7-dibromocarbazole (27-DBCZ) as building blocks via the Sonogashira-Hagihara cross-coupling reaction. In order to further improve the dispersibility of the as-resulting CMPs in water, hydrophilic CMPs (H-S-CMPs) were obtained by a sulfonation modification. The adsorption performance of H-S-CMPs on dyes and antibiotics was investigated, which was based on different experimental parameters such as the initial concentration, contact time, temperature, pH, and adsorbent dose. The adsorption isotherm, kinetics, and thermodynamics were also studied, and the possible adsorption mechanism of H-S-CMPs was discussed. The experimental results illustrated that the adsorption process of H-S-CMPs on dyes and antibiotics is more consistent with the Langmuir isotherm model and the pseudo-second-order kinetic model. The maximum adsorption capacities of H-S-CMPs for rhodamine B (RhB), methylene blue (MB), ciprofloxacin, and norfloxacin were 206.2, 324.7, 222.2, and 216.9 mg/g, respectively, which were determined according to the Langmuir isothern model. In addition, the adsorption mechanism of H-S-CMPs may be attributed to the synergistic effects of hydrogen bonding, electrostatic attraction, π-π stacking, and pore filling. After 5 cycles, H-S-CMPs still maintained good stability, and their removal rate of dyes could reach more than 70%. Notably, this polymeric hollow microsphere has been less extensively investigated as an adsorbent for the removal of dyes and antibiotics. As a result, based on the designable flexibility of CMPs and the unique structure of hollow microspheres, the material holds great promise for wastewater treatment in the presence of multiple pollutants.

Modeling and optimization of direct dyes removal from aqueous solutions using activated carbon produced from sesame shell waste

Today, there is a significant concern in the industry regarding the disposal of wastewater containing dyes into the environment, so the management and appropriate disposal of these wastes in the environment are considerable. The main aim of this study is to assess the efficiency of activated carbon (AC) prepared from sesame shells to remove direct dyes from aqueous solutions. According to the results, AC prepared from sesame shell had a high specific surface area (525 m2/g) and porous structure. The results demonstrated that the adsorbent had high potential to remove direct dyes as 84.5% of direct brown 103 (DB103), 93.08% of direct red 80 (DR80), 93.37% of direct blue 21 (DB21) and 98.39% of direct blue 199 (DB199) under the optimal conditions of adsorbent dose 4.8 g/L, contact time 19 min, pH 3 and initial dye concentration 12 mg/L. The experimental results showed that kinetic data were best described by the pseudo-second-order model (R2 = 0.989) while isotherm data were best fitted by the Freundlich model (R2 = 0.994). In the present study, not only was the produced waste used as a useful and economically valuable material, but it was also applied as an effective adsorbent to remove direct dyes from industrial effluents and reduce environmental pollution.

Sugarcane Bagasse Based Adsorbents and their Adsorption Efficacy on Removal of Heavy Metals from Nakuru Industrial Wastewater: Optimization, Kinetic and Thermodynamic Aspects

Currently, researchers are seeking to reduce heavy metal contamination from the environment, using agricultural waste materials like rice husk, groundnuts shells among others. The study focused on the removal of Cu(II), Pb(II), Cd(II), Ni(II), and Cr(III) ions from aqueous solutions and Nakuru industrial wastewater using sugarcane bagasse (NSCB) and valorised bagasse ash (VSCB), as alternative low-cost agricultural waste bio-sorbents. To achieve this goal, sugarcane bagasse was collected from Nzoia sugar industry in western Kenya, while the valorised bagasse was obtained by heating sugarcane bagasse sample in a muffle furnace at 300°C for three hours. Furthermore, batch adsorption studies were performed, and the effects of several factors, i.e. adsorbent particle size, pH, contact time, initial heavy metal ions concentration and temperature were investigated to optimise the removal efficiency of Pb, Cu, Cd, Ni, and Cr. The optimal adsorption conditions were pH of 5.0, adsorbent dosage of 0.1 g and ≤ 150µm particle size, equilibrium time of 60 minutes and at 25 degrees Celcius. The removal kinetics of the metal ions onto both adsorbents fitted well with the pseudo-second-order model. The removal kinetics of the metal ions onto both adsorbents fitted well with the pseudo-second-order model. The adsorption of Pb2+ and Ni2+ onto NSCB fitted better with the Freundlich isotherm model, while Cd2+, Cu2+ and Cr3+ showed better fit for the Langmuir isotherm model. As for VSCB adsorbent, Cr3+ has a better fit with the Langmuir isotherm model whereas Pb2+, Ni2+, Cd2+, and Cu2+ fitted well on the Freundlich isotherm model. Freundlich constant’s (1/n) values and the separation factor (RL) from the Langmuir isotherm model indicate that the metal ions were favourably adsorbed onto the adsorbents. Langmuir isotherm model was used to estimate the maximum adsorption capacities (qmax) for Cu(II), Pb(II), Ni(II), Cd(II), and Cr(III). The negative free energy change (∆G) values revealed that adsorption process of the metal ions onto NSCB and VSCB was spontaneous. Fourier Transform Infrared Spectroscopy (FTIR) was used for characterization studies. Interactions with metal ions caused the frequencies of the active functional groups, –OH, C=O and C=C, on the bio-sorbent surfaces to shift to higher values. Therefore, sugarcane bagasse and valorised bagasse have demonstrated higher potential to remove relatively all selected heavy metals in the industrial wastewater at controlled pH.