Adlayer Structure Research Articles

Electronic Oxide-Metal Strong Interactions (EOMSI) Localized at CeOx-Ag Interface.

Electronic oxide-metal strong interactions (EOMSI) refer to the electronic oxide-metal interactions (EOMI) between oxide adlayers and underlying metal substrate that is strong enough to stabilize supported oxide adlayers in a low-oxidation state, which individually is not stable under an ambient condition, from high temperature oxidation in air to a certain extent. Herein we report the deposition and electronic structure of CeOx adlayers on capping ligand-free cubic Ag nanocrystals, i.e., CeOx/Ag inverse catalysts. The EOMI occur via the charge transfer from Ag substrate to CeOx adlayers in the CeOx/Ag inverse catalyst, and the EOMSI are observed in the CeOx/Ag inverse catalyst with the average thickness of CeOx adlayers about 0.9 nm to exclusively form Ce2O3 adlayers stable against oxidation at 400 °C. As the thickness of CeOx adlayers increases, ceria adlayers with oxygen vacancies (CeO2-x) emerge and grow in the CeOx/Ag inverse catalysts, and the Ce3+/Ce4+ ratio decreases. Catalytic performance of CeOx/Ag inverse catalysts in the CO oxidation reaction is closely linked with the thickness and electronic structure of CeOx adlayers. These results demonstrate that the EOMSI and EOMI in the oxide/metal inverse catalysts are localized at the oxide-metal interface and sensitively vary with the thickness of oxide adlayers, offering a strategy of thickness engineering to tune electronic structures of oxide adlayers in oxide/metal inverse catalysts.

Interplay between the Formation of Colloidal Clathrate and Cubic Diamond Crystals.

Controlling the valency of directional interactions of patchy particles is insufficient for the selective formation of target crystalline structures due to the competition between phases of similar free energy. Examples of such are stacking hybrids of interwoven hexagonal and cubic diamonds with (i) its liquid phase, (ii) arrested glasses, or (iii) clathrates, all depending on the relative patch size, despite being within the one-bond-per-patch regime. Herein, using molecular dynamics simulations, we demonstrate that although tetrahedral patchy particles with narrow patches can assemble into clathrates or stacking hybrids in the bulk, this behavior can be suppressed by the application of external surface potential. Depending on its strength, the selective growth of either cubic diamond crystals or empty sII clathrate cages can be achieved. The formation of a given ordered network depends on the structure of the first adlayer, which is commensurate with the emerging network.

Impact of annealing treatment on adlayer structures of terphenylmethanethiol self-assembled monolayers on Au(111)

The scanning tunneling microscopy (STM) technique was employed to investigate the adlayer structure and morphology of Self-assembled monolayers (SAMs) fabricated from terphenylmethanethiol (TP1) molecules on Au(111) by preparing from an ethanolic solution at room temperature and subsequently annealed at various temperatures, reaching up to 468 K. Upon heat treatment, the TP1 adlayer exhibited a sequence of distinct structural phases characterized by varying molecular arrangements, namely α, β, γ, δ, ε, σ, and θ, emerging successively for both the as-prepared and annealed samples. The progressive transformation from α→β→ γ→δ→ε→σ→α→θ phases, driven by escalating annealing temperatures, entailed a gradual decrease in molecular packing density until the transition from γ→δ, followed by a subsequent increase leading to the formation of the most densely packed molecular network with molecules standing almost upright, referred to as the α phase, which is the same phase observed for non-heat-treated films. Interestingly, the desorption process for the annealed SAMs occurred from the densest packing TP1 molecular structure of the α phase, contrary to those of biphenyl-based organothiol and n-alkanethiol SAMs where desorption takes place from lying-down striped phases. Almost all TP1 molecules were desorbed at an annealing temperature of 468 K, leading to a significant alteration in the surface structure. During the annealing process, our results showed that the gold surface underwent remarkable changes, including the disappearance of the vacancy islands and the emergence of surface cracks in the form of trenches, along with the formation of rounded monoatomic gold islands with a densely packed α phase.

Impact of the Potential Dependent Surface Adlayer Composition on the ORR Activity and H2O2 Formation on Ru(0001) in Acid Electrolytes

AbstractStimulated by the increasing interest in ion adsorption effects on electrocatalytic reactions and by recent more detailed reports on the potential dependent adlayer structures formed on Ru(0001) in pure HClO4 and H2SO4 electrolytes, we revisited the oxygen reduction reaction (ORR) on structurally well‐defined Ru(0001) single crystal surfaces prepared under ultrahigh vacuum conditions. We demonstrate that the complex, potential‐dependent activity both for the ORR and for H2O2 formation is closely related to potential‐dependent changes in the composition and structure of the adlayer. Our results demonstrate the enormous effects adsorbed species can have on the ORR reaction characteristics, either by surface blocking, e. g., by (co‐)adsorbed bisulfate species, or by participation in the reaction, e. g., by *H transfer from adsorbed H or OH to O2. The comparison with results obtained on polycrystalline Ru, which differ significantly from Ru(0001) data, furthermore underlines the importance of using structurally well‐defined surfaces as a reference system for future theoretical studies.

Maintaining the order: 4,4′-bipyridine self-assembled layers on the Bi(111) | ionic liquid interface

The organised layer of molecules on a solid surface is at the centre of numerous molecular devices. Although the adsorption of molecules from aqueous electrolytes has been thoroughly investigated, only a limited number of studies have focused on the adsorption from ionic liquid electrolytes. This paper characterises the 4,4′-bipyridine adsorption at the Bi(111) | ionic liquid interface. We combined electrochemical impedance spectroscopy and scanning tunnelling microscopy with density functional theory calculations to gain a comprehensive overview of the interfacial processes. The results show a notable influence of electrode potential and the electrolyte on the 4,4′-bipyridine adsorption behaviour. The formation of organic adlayer on the electrode's surface was demonstrated, while highly organised striated adlayer structure was visualised only in a narrow potential range.

Interfacially Confined Dynamic Reaction Resulted to Fluorescent Nanofilms Depicting High-Performance Ammonia Sensing.

Sensing materials innovation plays a crucial role in the development of high-performance film-based fluorescent sensors (FFSs). In our current study, we present the innovative fabrication of four fluorescent nanofilms via interfacially confined dynamic reaction of a specially designed fluorescent building block, a new boron-coordinated compound (NI-CHO), with a chosen one, benzene-1,3,5-tricarbohydrazide (BTH). The nanofilms as prepared are robust, uniform, flexible, and thickness tunable, at least from 40 to 1500 nm. The fabricated FFSs based on Film 3, one of the four nanofilms, shows highly selective and fully reversible response to NH3 vapor with an experimental detection limit of <0.1 ppm and a response time of 0.2 s. The unprecedented high performance of the nanofilm is ascribed to the specific quenching of its fluorescence emission owing to formation of an excited-state complex between the sensing unit and the analyte molecule. Efficient mass transfer also contributes to the high performance owing to the porous adlayer structure of the nanofilm. This work provides an example to show how to develop a high-performance sensing film via controlling the film's structure, especially the thickness.

Two-dimensional ice-like water adlayers on a mica surface with and without a graphene coating under ambient conditions.

Water tends to wet all hydrophilic surfaces under ambient conditions, and the first water adlayers on solids are important for a broad range of physicochemical phenomena and technological processes, including corrosion, wetting, lubrication, anti-icing, catalysis, and electrochemistry. Unfortunately, challenges in characterizing the first water adlayer in the laboratory have hampered molecular-level understanding of the contact water structure. Herein, we present the first ab initio molecular dynamics simulation evidence of a previously unreported ice-like adlayer structure (named as Ice-AL-II) on a prototype mica surface under ambient conditions. Calculation showed that the newly identified Ice-AL-II structure is more stable than the widely recognized ice-adlayer structure on mica surfaces (named as Ice-AL-I). Ice-AL-II exhibited a face-centered corner-cut tetragon (or a face-centered irregular pentagon) pattern of a hydrogen-bonded network. The center of the corner-cut tetragon was occupied by either a K+ cation or a water molecule with two H atoms pinned by the mica (100) via double hydrogen bonds. Our simulation also suggested that bilayer Ice-AL-II favors AA stacking rather than AB stacking. Interestingly, when a graphene sheet was coated on top of the ice-like adlayer, the stability of Ice-AL-II was further enhanced. In contrast, due to its strongly puckered structure, the Ice-AL-I structure could be crushed into a near-Ice-AL-II structure by the graphene coating. Ice-AL-II is thus proposed as a promising candidate for the ice-like structure on a mica surface detected by scanning polarization force microscopy and by atomic force microscopy between a graphene coating and a mica surface.

Effect of Chlorine on Copper Electrodissolution

A computational study on the role of adsorbed Cl ions on copper dissolution is presented. Extensive grand canonical Monte Carlo (GCMC) calculations using reactive force-field (ReaxFF) are used to check the formation chlorine (Cl) adlayer structures on Cu (100) surface as a function of the chemical potential (µ). From experimental studies conducted by other researchers it has been observed that Cl adlattice on Cu in c(2X2) at maximum coverage. We observe that at low µ, Cl adlayer is disordered and moves to ordered c(2X2) structure at high µ. The binding energy of Cl, oxygen (O), hydroxide (OH-) and H2O on Cu at different sites is calculated and compared with Density-functional theory (DFT) values. Metal surface is often highly uneven and rough during electrodissolution process. Therefore, we also discuss the adsorption isotherm, disorder-order transformation, and preferential adsorption sites for rough surfaces. Specific anion adsorption (SAA) of Cl involves partial charge transfer to Cu substrate and these effect the type of bond and bond strength which is also briefly discussed. The electrodissolution of Cu in the presence of Cl is modelled using kinetic Monte Carlo simulation to obtain the polarization curve.Keywords: Adsorbed chlorine, electrodissolution, grand canonical monte carlo, molecular dynamics, ReaxFF, kinetic monte carlo.

Fast and Selective Luminescent Sensing by Langmuir–Schaeffer Films Based on Controlled Assembly of Perylene Bisimide Modified with A Cyclometalated AuIII Complex

AbstractCondensed films of functional luminophores dominated by the magnitude and dimensionality of the intermolecular interactions play important roles in sensing performance. However, controlling the molecular assembly and regulating photophysical properties remain challenging. In this study, a new luminophore, ortho‐PBI‐Au, was synthesized by anchoring a cyclometalated alkynyl‐gold(III) unit at the ortho‐position of perylene bisimide. An unprecedented T‐type packing model driven by weak Au‐π interaction and Au−H bonds was observed, laying foundation for striking properties of the luminophore. Controlled assembly of ortho‐PBI‐Au at the air‐water interface, realized using the classical Langmuir–Schaeffer technique, afforded the obtained luminescent films with different packing structures. With an optimized film, sensitive, selective, and rapid detection of a hazardous new psychoactive substance, phenylethylamine (PEA), was achieved. The detection limit, response time, and recovery time were &lt;4 ppb, &lt;1 s, and &lt;5 s, respectively, surpassing the performance of the PEA sensors known thus far. The relationship between the characters of films and the sensing performance was systematically examined by grey relational analysis (GRA). The present study suggests that designing novel molecular aggregation with definite adlayer structure is a crucial strategy to enhance the sensing performance, which could be favorable for the film‐based fluorescent sensors.

Fast and Selective Luminescent Sensing by Langmuir-Schaeffer Films Based on Controlled Assembly of Perylene Bisimide Modified with A Cyclometalated AuIII Complex.

Condensed films of functional luminophores dominated by the magnitude and dimensionality of the intermolecular interactions play important roles in sensing performance. However, controlling the molecular assembly and regulating photophysical properties remain challenging. In this study, a new luminophore, ortho-PBI-Au, was synthesized by anchoring a cyclometalated alkynyl-gold(III) unit at the ortho-position of perylene bisimide. An unprecedented T-type packing model driven by weak Au-π interaction and Au-H bonds was observed, laying foundation for striking properties of the luminophore. Controlled assembly of ortho-PBI-Au at the air-water interface, realized using the classical Langmuir-Schaeffer technique, afforded the obtained luminescent films with different packing structures. With an optimized film, sensitive, selective, and rapid detection of a hazardous new psychoactive substance, phenylethylamine (PEA), was achieved. The detection limit, response time, and recovery time were <4 ppb, <1 s, and <5 s, respectively, surpassing the performance of the PEA sensors known thus far. The relationship between the characters of films and the sensing performance was systematically examined by grey relational analysis (GRA). The present study suggests that designing novel molecular aggregation with definite adlayer structure is a crucial strategy to enhance the sensing performance, which could be favorable for the film-based fluorescent sensors.

Solution-Processed Formation of DNA-Origami-Supported Polyoxometalate Multi-Level Switches with Countercation-Controlled Conductance Tunability

We report a chemically programmed design and the switching characteristics of a functional metal–DNA-origami–polyoxometalate (POM) material obtained from the solution-processed assembling of biocompatible molecular precursors. The DNA origami is immobilized on the gold surface via thiolate groups and acts as a carrier (ad-layer) structure, ensuring the spatially controlled hybridization of the pre-defined six-helix bundle (6HB) positions with DNA-augmented, tris(alkoxo)-ligated Lindqvist-type polyoxovanadate (POV6) units. The DNA-confined POV6 units accept electrons in a stepwise fashion, allowing for a multi-logic function, which we directly probe using scanning tunneling electron microscopy and spectroscopy. Electron acceptance and injection into the originally non-conducting DNA structure and the subsequent release to the gold substrate depend upon the potential at the nanoscale tip and the oxidation state of POV6, as well as on the mechanism of action of POV6 countercations. By combining experiment and theory, we show that the bio-hybrid heterojunction has far-reaching potential to create a chemically controlled POM-based nano-environment with synaptic behavior.

New approaches to study of mismatched interfaces structure on low-index surfaces by molecular dynamics simulation

We used molecular dynamics simulations to study the structure of mismatched Al/Ni and Ag/Cu interfaces, considering low-index surfaces of the substrate. Embedded Atom Potentials are being employed to mimic atomic interactions between the different elements. The effect of the substrate orientation on the adlayer structure is investigated. The results showed that, on the (111) substrate, the adlayer presents a coincidence site lattice characterized by a rotation (labeled α) with respect to the substrate. This coincidence site lattice may contain dislocations and twin boundary that can be produced by the occurrence of a twin spirals (with opposite directions). To accommodate the adlayer deposition on the substrate, a slight shuffling of some atoms occurs in the substrate and leads to a rectangular structures producing a dislocation. Furthermore, on the (001) substrate, the accommodation of the triangular structure on the square lattice (substrate) is produced by a shift of some atomic rows producing a dislocation. But, the agglomeration of several square structures of 2d shape gives rise to a polycrystal delimited by a disclination forming grain boundaries and vacancies. However, the inward adsorption on the (110) substrate restricts the space of extension of adsorbed atoms, producing linear cracks. The relaxation of atoms adsorbed on these cracks change the linear shape of vacancies towards a staircase structure.

Submonolayer and Monolayer Sn Adsorption and Diffusion Behavior on Oxidized Nb(100)

Current efforts to produce brighter beams of charged particles are focused on developing Nb3Sn-coated superconducting radio frequency (SRF) cavities for use in superconducting accelerator facilities. The growth mechanisms driving the formation of Nb3Sn films on preexisting Nb SRF cavities are not, however, fully understood. In order to understand the complex interplay between metallic Sn and the oxidized Nb surface leading to Nb3Sn alloy formation, we have examined how the structural and chemical composition of an oxidized Nb(100) single crystal influences Sn adsorption and diffusion behavior at submonolayer and monolayer Sn coverages. Sn was deposited on an NbO surface and annealed at temperatures relevant to Nb3Sn growth procedures before analysis via in situ scanning tunneling microscopy (STM). Experimental data, along with supporting simulated STM and calculated binding energies obtained using density functional theory, revealed the influence of Sn coverage and annealing temperatures on thermodynamic and kinetically driven diffusion pathways, preferred binding sites, novel Sn adlayer structures, and how the underlying NbO substrate evolves to accommodate Sn diffusion. This newly realized understanding of the interfacial chemical interactions between adsorbed Sn and the Nb surface sites is essential to develop predictive growth models for Nb3Sn films for use in future SRF cavities.

Pursuing colloidal diamonds.

The endeavor to selectively fabricate a cubic diamond is challenging due to the formation of competing phases such as its hexagonal polymorph or others possessing similar free energy. The necessity to achieve this is of paramount importance since the cubic diamond is the only polymorph exhibiting a complete photonic bandgap, making it a promising candidate in view of photonic applications. Herein, we demonstrate that due to the presence of an external field and delicate manipulation of its strength we can attain selectivity in the formation of a cubic diamond in a one-component system comprised of designer tetrahedral patchy particles. The driving force of such a phenomenon is the structure of the first adlayer which is commensurate with the (110) face of the cubic diamond. Moreover, after a successful nucleation event, once the external field is turned off, the structure remains stable, paving an avenue for further post-synthetic treatment.

Electroconvective Flow in Liquid Electrolytes Containing Oligomer Additives

Metal electrodeposition in batteries is fundamentally unstable and affected by different instabilities depending on operating conditions and electrolyte chemistry. Particularly, at high charging rates, a hydrodynamic instability loosely termed electroconvection sets in, which complicates all electrochemical processes by creating a nonuniform ion flux and preferential deposition at the electrode. Here, we isolate and study electroconvection by experimentally investigating how oligomer additives in liquid electrolytes interact with the hydrodynamic instability at a cation selective interface. From electrochemical measurements and direct visualization experiments, we find that electroconvection is delayed and suppressed at all voltages in the presence of oligomers. The underlying mechanism is revealed to involve formation of an oligomer ad-layer at the interface, which in response to perturbation is believed to exert an opposing body force on the surrounding fluid to preserve the ad-layer structure and in so doing suppresses electroconvection. Our results therefore reveal that in battery electrolytes without obvious sources of bulk elasticity, surface forces produced by adsorbed polymers can be used to advantage for suppressing instability.

Self-Assembled Monolayers of Molecular Conductors with Terpyridine-Metal Redox Switching Elements: A Combined AFM, STM and Electrochemical Study

Self-assembled monolayers (SAMs) of terpyridine-based transition metal (ruthenium and osmium) complexes, anchored to gold substrate via tripodal anchoring groups, have been investigated as possible redox switching elements for molecular electronics. An electrochemical study was complemented by atomic force microscopy (AFM) and scanning tunneling microscopy (STM) methods. STM was used for determination of the SAM conductance values, and computation of the attenuation factor β from tunneling current-distance curves. We have shown that SAMs of Os-tripod molecules contain larger adlayer structures compared with SAMs of Ru-tripod molecules, which are characterized by a large number of almost evenly distributed small islands. Furthermore, upon cyclic voltammetric experimentation, Os-tripod films rearrange to form a smaller number of even larger islands, reminiscent of the Ostwald ripening process. Os-tripod SAMs displayed a higher surface concentration of molecules and lower conductance compared with Ru-tripod SAMs. The attenuation factor of Os-tripod films changed dramatically, upon electrochemical cycling, to a higher value. These observations are in accordance with previously reported electron transfer kinetics studies.

Structure of the (Bi)carbonate Adlayer on Cu(100) Electrodes.

(Bi)carbonate adsorption on Cu(100) in 0.1 M KHCO3 has been studied by in situ scanning tunneling microscopy. Coexistence of different ordered adlayer phases with ( ×6 )R45° and (4×4) unit cells was observed in the double layer potential regime. The adlayer is rather dynamic and undergoes a reversible order-disorder phase transition at 0 V vs. the reversible hydrogen electrode. Density functional calculations indicate that the adlayer consists of coadsorbed carbonate and water molecules and is strongly stabilized by liquid water in the adjacent electrolyte.

Structure of the (Bi)carbonate Adlayer on Cu(100) Electrodes

Abstract(Bi)carbonate adsorption on Cu(100) in 0.1 M KHCO3 has been studied by in situ scanning tunneling microscopy. Coexistence of different ordered adlayer phases with ( ×6 )R45° and (4×4) unit cells was observed in the double layer potential regime. The adlayer is rather dynamic and undergoes a reversible order‐disorder phase transition at 0 V vs. the reversible hydrogen electrode. Density functional calculations indicate that the adlayer consists of coadsorbed carbonate and water molecules and is strongly stabilized by liquid water in the adjacent electrolyte.

Adlayer formation on C-plane (0001) and R-plane Al2O3 surfaces.

Adlayers on C-plane (0001) and R-plane terminated surfaces of corundum phase aluminum oxide were synthesized by annealing mixtures of two oxide powders, aluminum oxide with an additive. Using high-angle annular dark field scanning transmission electron microscopy, the adsorbed layers were characterized, and image simulations aided interpretation of the results. The adlayers were pseudomorphic, one atomic layer thick and with a fractional site occupancy. Atomic positions of the adlayer atoms relaxed and changed relative to the bulk structure, where there is evidence that the magnitude of the relaxation is sensitive to the ionic radius of the adsorbate. The pseudomorphic adlayer structure formed for different elements including, but not limited to, the lanthanides (i.e., Ge, Ba and Ln = La, Ce, Pr, Nd, Sm, Eu, Gd, Dy, Ho, Er, Tm).

Fast and Selective Detection of Trace Chemical Warfare Agents Enabled by an ESIPT-Based Fluorescent Film Sensor.

Reliable detection of airborne chemical warfare agents (CWAs) at the site and in real-time remains a challenge due to the rarity of miniaturized analytical tools. Herein, an o-carborane-functionalized benzothiazole derivative (PCBO) with excited-state intramolecular proton transfer (ESIPT) and AIE characteristics was synthesized. The PCBO-based film sensor showed a highly sensitive response to representative simulants of CWAs, and detection limits were found to be 1.0 mg·m-3 for triphosgene, 6.0 mg·m-3 for chloroethyl ethyl sulfide, and 0.2 mg·m-3 for diethyl chlorophosphite. Moreover, the sensor showed great reusability (>100 cycles) and unprecedented response speed (<0.5 s). The excellent sensing performance was ascribed to the microenvironmental sensitivity of the sensing fluorophore, the porous adlayer structure of the film, and the specific binding of the fluorophore to the analytes. Furthermore, discrimination and identification of the examined CWA simulants were realized via the introduction of another fluorophore (HCBO)-based film. Importantly, a portable fluorescent CWA detector was built with the sensor as the key component, and its applicability was demonstrated by the successful detection of a typical CWA sample (Sarin). The present study indicates that fluorescent film sensors could satisfy reliable onsite and real-time detection of harmful chemicals.