Amount Of Adhesion Research Articles

Indole-3-acetic acid regulating the initial adhesion of microalgae in biofilm formation

Regulating the microalgal initial adhesion in biofilm formation is a key approach to address the challenges of attached microalgae cultivation. As a type of phytohormone, Indole-3-acetic acid (IAA) can promote the growth and metabolism of microalgae. However, limited knowledge has been acquired of how IAA can change the initial adhesion of microalgae in biofilm formation. This study focused on investigating the initial adhesion of microalgae under different IAA concentrations exposure in biofilm formation. The results showed that IAA showed obvious hormesis-like effects on the initial adhesion ability of microalgae biofilm. Under exposure to the low concentration (0.1 mg/L) of IAA, the initial adhesion quantity of microalgae on the surface of the carrier reached the highest value of 7.2 g/m2. However, exposure to the excessively high concentration (10 mg/L) of IAA led to a decrease in the initial adhesion capability of microalgal biofilms. The enhanced adhesion of microalgal biofilms due to IAA was attributed to the upregulation of genes related to the Calvin Cycle, which promoted the synthesis of hydrophobic amino acids, leading to increased protein secretion and altering the surface electron donor characteristics of microalgal biofilms. This, in turn, reduced the energy barrier between the carriers and microalgae. The research findings would provide crucial support for the application of IAA in regulating the operation of microalgal biofilm systems.

Construction of a Soft Antifouling PAA/PSBMA Hydrogel Coating with High Toughness and Low Swelling through the Dynamic Coordination Bonding Provided by Al(OH)3 Nanoparticles.

Marine biofouling, resulting from the adhesion of marine organisms to ship surfaces, has long been a significant issue in the maritime industry. In this paper, we focused on utilizing soft and hydrophilic hydrogels as a potential approach for antifouling (AF) coatings. Acrylic acid (AA) with a polyelectrolyte effect and N-(3-sulfopropyl)-N-(methacryloxyethyl)-N,N-dimethylammonium betaine (SBMA) with an antipolyelectrolyte effect were selected as monomers. By adjusting the monomer ratio, we were able to create hydrogel coatings that exhibited low swelling ratio in both fresh water and seawater. The Al(OH)3 nanoparticle, as a physical cross-linker, provided better mechanical properties (higher tensile strength and larger elongation at break) than the chemical cross-linker through the dynamic coordination bonds and plentiful hydrogen bonds. Additionally, we incorporated trehalose into the hydrogel, enabling the repair of the hydrogel network through covalent-like hydrogen bonding. The zwitterion compound SBMA endowed the hydrogel with excellent AF performance. It was found that the highest SBMA content did not lead to the best antibacterial performance, as bacterial adhesion quantity was also influenced by the charge of the hydrogel. The hydrogel with appropriate SBMA content being close to electrical neutrality exhibits the strongest zwitterionic property of PSBMA chains, resulting in the best antibacterial adhesion performance. Furthermore, the pronounced hydrophilicity of SBMA enhanced the lubrication of the hydrogel surface, thereby reducing the friction resistance when applied to the hull surface during ship navigation.

Investigating the effect of particle slenderness ratio on optimizing the mechanical properties of particleboard using the response surface method

Restricted formaldehyde gas emissions and a scarcity of lignocellulosic raw materials have particleboard companies in Iran concerned about raw materials and adhesive use. The particle slenderness ratio is one of the main parameters that leads to the required mechanical characteristics of particleboard, together with the simultaneous decrease of density (raw materials) and the quantity of adhesive. The objective of this study was to evaluate the mechanical properties of particleboard composed of poplar particles with variables of density, adhesive quantity, and slenderness ratio using response surface technique. The variables were then optimized for the examined responses according to the EN 312-3 (1993) standard for the manufacturing of particleboard for domestic use as well as home and office furniture. Particleboard with minimum allowable properties according to EN 312-3 (MOR = 11 MPa, MOE = 1.6 GPa, and IB = 0.35 MPa) with a density of 0.65 g/cm3, adhesive percentage of 10.54, and a slenderness ratio of 37.5 can be produced, according to optimization findings. Through raising the density to 0.69 g/cm3 and the slenderness ratio to 46.99, the quantity of adhesive utilized in particleboard manufacturing could be decreased from 10.54 to 8.9% while keeping the minimum allowable resistances of EN 312-3 (1993) standard.

Effect of crosslinker to monomer ratio on the adhesion and size distribution of silver nanoparticles grown on poly (methacrylic acid) microspheres

In this study poly methacrylic acid (MAA) microparticles were synthesized with variations in methylene-bis-acrylamide (MBA), with MBA in the role of the crosslinker. The as produced microparticles serve as substrates for the growth of silver nanoparticles while evaluating the effect of different crosslinker content. Each formulation was assessed in terms of silver nanoparticle adhesion, size distribution and silver quantity. Experimental evidence reveals that while incorporating crosslinker above 20 wt% with respect to the monomer, silver nanoparticle adhesion to the polymer surface increases, whereas in formulations above 35 wt% microparticle morphology hinders silver ion binding and the subsequent formation of silver nanoparticles. In addition, TEM microcopy combined with image classification analysis reported that in the range of 20–35 wt% MBA content, silver nanoparticle size distribution can be tuned. Evidently, MBA content between 20 wt% and 35 wt% (in relation to MAA) exhibits a dynamic state where carboxylic acid terminated functional side groups and amino-terminal side groups provide a synergistic effect in silver ion binding thus opening a functional pathway towards the controlled synthesis of silver nanoparticles.

Influence of surface properties on the adhesion of bacteria onto different casings

Bacteria adhere to the surfaces of sausage casing and form biofilms, which causes food spoilage and quality deterioration. However, bacterial adhesion to the casing surfaces has not received enough attention and has not been extensively studied. In this study, the effect of the physicochemical properties of casing surfaces on bacterial initial adhesion were investigated with Leuconostoc mesenteroides as model bacteria. The adhesion of Leuconostoc mesenteroides onto 5 types of casings were systematically investigated, including animal casings, collagen casings, cellulose casings, fiber casings, and nylon casings, which are the most frequently encountered casings in sausage processing. It was found that the number of viable cells on the casings following the trend as: animal casings > collagen casings > fiber casings > cellulose casings > nylon casings after 4 h of incubation time. This phenomenon might be due to the different physicochemical properties of the different casings. Therefore, physicochemical factors, including zeta potential, hydrophobicity and roughness of casings, zeta potential and hydrophobicity of Leuconostoc mesenteroides, were further characterized. In terms of hydrophobic interactions, the results showed that the number of bacteria attached to the casings did not conform to the trend of hydrophobic interaction. In terms of electrostatic interactions, the results showed that the number of bacteria attached to the casings did not conform to the trend of hydrophobic interaction. The casings with different surface roughnesses in a range of 1.67–20.83 μm, the variation of bacterial adhesion quantity was in good agreement with the variation trend of casing roughness, the result showed that the surface roughness was the key factor dominating the bacterial adhesion rate compared with the surface hydrophobicity and zeta potential. The results give new insights to explore the mechanism of bacterial adhesion on casings and prevent sausage spoilage.

Loofah Sandwich Panels: The Effect of Adhesive Content on Mechanical and Physical Properties.

In the development of new materials, the focus nowadays is increasingly on their relevance with regard to lightweight construction or environmental compatibility. The idea of a lightweight sandwich panel was inspired by an increasing number of cosmetic accessories that use the fibers of the loofah plant, a rapidly renewable, light, fibrous raw material. The aim of the study was to develop a fiber composite panel based on the fibers of the loofah plant (Luffa cylindrica) as core material and wooden veneer as the skin layer to be used in areas of lead construction. Three different panel variations were produced for the tests, with a fiber–adhesive ratio between 1:1.05, 1:0.8, and 1:0.5. The mechanical strength (flexural strength and internal bond) and the physical properties (density and thickness swelling) were determined as a function of the fiber–adhesive composition. The results show that the flexural strength increased by approx. 400% and the thickness swelling was reduced by 10% with increasing adhesive quantity.

Ballistic impact response and failure mechanism of aluminum/ultrahigh molecular weight polyethylene fiber laminates with different adhesive quantity

AbstractThe aim of this study is to investigate the effects of metal‐composite interface (MCI) adhesive quantity on the energy absorption and failure behavior of fiber metal laminates (FMLs) under ballistic impact. The dynamic shear and ballistic impact tests were systematically conducted, and CT scan was employed to quantitatively investigate the damage and failure mechanisms of the FMLs. The results reveal that the dynamic shear strength of MCI initially increases and then remains constant with the increase in the adhesive quantity at a constant strain rate. Moreover, the MCI adhesive quantity has a certain influence on the impact energy absorption of FMLs, and the degree of influence is related to the impact velocity. At an impact velocity of 360 m/s, the difference of energy absorption is maximal, approximately 14.7%. The distribution of total debonding area changes with increase in the adhesive quantity. When the impact velocity is 212 m/s, compared to FMLs with the lowest adhesive quantity, the total debonding area of FMLs with the highest adhesive quantity decreases by 774.57 mm2 (9.20%), otherwise the debonding area near the rear aluminum alloy sheet increases by 595.94 mm2 (58.99%).

Novel environment-friendly grease-infused porous surface exhibiting long-term cycle effective antifouling performance

With the increasingly strict requirements for marine environmental protection, the demand for antifouling coatings that can replace organotin is becoming more urgent. Here, environmentally friendly lubricants were infused into porous surfaces to obtain antifouling coating. The stability of the coating was evaluated by the contact angle and sliding angle tests. The antifouling performance was intuitively represented by the adhesion quantity of three marine algae. The adhesion experiment showed that a lubricating oil of suitable viscosity balanced stability and lubricity, so that the silicone oil (PMX200-100)-infused surface showed the best antifouling effect. However, it was covered by Navicula exigua (N. exigua) after a long time of immersion. In our work, the grease-infused surface displayed outstanding stability in water. In addition, the grease-infused porous surface showed another state of algae attachment after a period of immersion in algae solution. Algae adhered to the surface and congregated to form a layer of biofilm, but it could be easily removed and re-expose the new grease-infused surface. The requirement of lubricating grease for porous surface structures is not as high as that of lubricating oil. The grease-infused surface has a long-term circulation antifouling effect on algae.

Effects of surface pre-treatment and adhesive quantity on interface characteristics of fiber metal laminates

ABSTRACT Fiber metal laminates (FMLs) are hybrid materials consisting of metals and fiber-reinforced composite materials. The characteristics of interfaces between metal layers and layers of composites directly determine the damage tolerance and impact resistance of FMLs. In this study, the effects of surface pre-treatment and adhesive quantity on the interface of FMLs were investigated. Aluminum substrates were treated with sandpaper and anodizing. The treated surface structure and joint shear strength were evaluated to analyze the bonding interface quality. The results show that the surface roughness, structure and thickness of the anodized films affect the interface characteristics and adhesion strength. A porous oxide layer was formed on the substrate surface after anodization, resulting in a better wetting surface than that of sanded. Moreover, statistical analysis of the surface structures reveals that the shear strength of phosphoric acid anodizing treatment was higher than other anodizing. With the increase in adhesive layers, the lap shear strength was markedly improved at the beginning but slowly increased thereafter. From the results, the surface pre-treatment and adhesive quantity could be optimized to improve the manufacturing process of FMLs.

Comparing Five New Polymer Barriers for the Prevention of Intra-abdominal Adhesions in a Rat Model

BackgroundIntra-abdominal adhesions affect up to 93% of the patients after abdominal surgery, causing small-bowel obstruction, infertility, chronic abdominal pain, and iatrogenic bowel injury at reoperation. The efficacy of five new polymer antiadhesive barriers to avoid adhesion formation is evaluated in an ischemic button model in rats. Materials and methodsFive new, biodegradable polyurethane and copolyester-based, antiadhesive barriers (A1, A2, A3, B1, and B2) were evaluated in separate experimental groups and compared with two control groups (hyaluronate carboxymethylcellulose barrier and no antiadhesive barrier) in an ischemic button model (n = 11 per group operated). After 14 d, the quantity and quality of the adhesions were scored macroscopically. The Kruskal–Wallis with Mann–Whitney U post hoc and the Fisher's exact tests were used for data analysis. The Bonferroni correction method was applied, and a P-value <0.007 was considered significant. ResultsTwo animals died during surgery and follow-up. A significant reduction of adhesions to ischemic buttons was found in the A2 group (median, 3.5; interquartile range, 2.25) compared with no adhesive barrier (median, 8.0; interquartile range, 2.0) (P = 0.001). The remaining groups did not differ significantly regarding adhesion quantity or quality. Adverse events were observed in the A2, A3, and B2 groups. ConclusionsThe A2 antiadhesive barrier reduced the adhesion formation significantly compared with no anti-adhesive barrier, but applicability is questionable because of extensive adverse events observed due to implantation of the anti-adhesive barrier. The Nair score appears not to be sensitive enough to detect differences in adhesion formation in this model. Future research should focus on anti-adhesive barriers that are self-adhering.

Effect of adhesive quantity on selected physico-mechanical properties of Bamboo glulam

This study was aimed at determining the optimal glue quantity for bamboo lamination. Bamboo laminated boards were produced using glue applied at three different rates: 150 g/m2, 200 g/m2 and 250 g/m2. The boards produced were evaluated for their physical (density, longitudinal, tangential, radial and volumetric shrinkage) and mechanical (impact bending strength, modulus of elasticity, modulus of rupture and maximum compressive strength parallel to grain properties. It was discovered that the boards were uniform in their investigated physical properties but the glue quantity significantly influenced both the impact bending strength and modulus of rupture of the boards. Based on the results, it was observed that the boards produced with glue applied at the rate of 200 g/m2 met all the technical specifications on the basis of the investigated physical and mechanical properties, hence, concluded to be the optimal glue quantity for bamboo lamination. Keywords: Bambusa vulgaris, compressive strength, density, glue application rate, optimal glue quantity

A prospective randomized experimental study to investigate the peritoneal adhesion formation after waterjet injection and argon plasma coagulation (HybridAPC) in a rat model.

This prospective, randomized, controlled, single-blinded study investigates the peritoneal adhesion formation of HybridAPC (waterjet elevation of the peritoneum with subsequent argon plasma coagulation) versus only waterjet (elevation with the same instrument, but without subsequent argon plasma coagulation) in a rat model (24 female Wistar rats). Bilateral lesions were created on the abdominal wall with HybridAPC on one sidewall and waterjet elevation on the other sidewall of the peritoneum in a standard fashion. After 10days, the rats were euthanized to evaluate the peritoneal trauma sites. Adhesion incidence, quantity, and quality were scored 10days postoperatively and studied histopathologically. Incidence of adhesion formation was 2.3% for HybridAPC; no adhesions occurred for peritoneal elevation with saline (p=1.00). Histologic evaluation revealed no acute inflammation in both groups. An overall moderate degree of granulation tissue formation and myonecrosis was observed in the HybridAPC group, whereas no chronic inflammation and myonecrosis occurred after elevation without thermal ablation (p<0.0001). This study investigates the effect of waterjet elevation of the peritoneum with and without subsequent thermal ablation on adhesion formation in a rat model for the first time. Peritoneal waterjet elevation with saline does not provide any risk of adhesion formation. Thermal coagulation with APC after waterjet elevation of the peritoneum creates advantageous peritoneal conditions due to a permanent moist tissue surface and the cooling effect of the injected solution, resulting in no significant difference in adhesion formation compared to peritoneal elevation without thermal ablation. HybridAPC can thus be regarded as a beneficial coagulation method with only minor adhesion formation due to positive tissue effects of the combined waterjet.

Solid-Liquid Interface Thermal Resistance Affects the Evaporation Rate of Droplets from a Surface: A Study of Perfluorohexane on Chromium Using Molecular Dynamics and Continuum Theory.

We study the role of solid-liquid interface thermal resistance (Kapitza resistance) on the evaporation rate of droplets on a heated surface by using a multiscale combination of molecular dynamics (MD) simulations and analytical continuum theory. We parametrize the nonbonded interaction potential between perfluorohexane (C6F14) and a face-centered-cubic solid surface to reproduce the experimental wetting behavior of C6F14 on black chromium through the solid-liquid work of adhesion (quantity directly related to the wetting angle). The thermal conductances between C6F14 and (100) and (111) solid substrates are evaluated by a nonequilibrium molecular dynamics approach for a liquid pressure lower than 2 MPa. Finally, we examine the influence of the Kapitza resistance on evaporation of droplets in the vicinity of a three-phase contact line with continuum theory, where the thermal resistance of liquid layer is comparable with the Kapitza resistance. We determine the thermodynamic conditions under which the Kapitza resistance plays an important role in correctly predicting the evaporation heat flux.

Effect of adhesive quantity on failure behavior and mechanical properties of fiber metal laminates based on the aluminum–lithium alloy

The effect of adhesive quantity on the failure behavior and mechanical properties of fiber metal laminates based on the aluminum–lithium alloys (NFMLs) was investigated to optimize the manufacture process and further recognize the interface interaction. The NFMLs with different adhesive quantities (0g/m2, 20g/m2, 40g/m2, 60g/m2) were prepared primarily. Then, the influence of adhesive quantity on the interlaminar, tensile, flexural and fatigue properties of NFMLs was studied respectively. Also, the failure behaviors of NFMLs under different loading conditions were revealed. The results indicated that the adhesive layers significantly enhanced the interlaminar properties of the NFMLs within the investigated quantities. Moreover, the reasonable adhesive quantity also greatly improved the mechanical properties of the laminates, while an excessive amount deteriorated the performance. For the different properties, the peak values appeared under different adhesive quantities. Besides, the changing mechanical properties followed with the variation of failure mode. From the engineering perspective, the adhesive quantity of 40g/m2 is optimal to achieve the excellent performance of NFMLs.

Shear Strength of Conductive Adhesive Joints on Rigid and Flexible Substrates Depending on Adhesive Quantity

Abstract This article deals with the impact of electrically conductive adhesive quantity on the shear strength of joints glued by adhesives “EPO-TEKⓇ H20S” and “MG8331S” on three types of substrates (FR-4, MELINEXⓇST504, DuPont™ PyraluxⓇAC). These joints were made by gluing chip resistors 1206, 0805 and 0603, with two curing profiles for each adhesive. Different thicknesses of stencil and reductions in the size of the hole in stencils were used for this experiment. These differences have an effect on the quantity of conductive adhesives which must be used on the samples. Samples were measured after the curing process by using a shear strength test applied by the device LabTest 3.030. This article presents the effects of different curing profiles, various types of substrates, and different quantities of adhesives on the mechanical strength of the joint.

Preparation and Performance Evaluation of Bamboo Lumber Prepared by Assembly and Glue-Curing of Naturally Arc-Shaped Segments with Finger Joints

Using bamboo to replace wood has great significance for the protection of forests. This work presents the concept of the reorganization of arc bamboo sheet to produce recombined arc-segment bamboo lumber (RABL). Several key preparation technology parameters were investigated. Results showed that when the phenol resin (PF) double-sided adhesive quantity was 250 g/m2, unit pressure was 2.0 MPa, screen voltage was 4200 V, screen current was 1.5 A, and hot pressing time was 30 s/mm, the modulus of rupture (MOR) of the RABL was 105 MPa and the modulus of elasticity (MOE) was 5000 MPa. These parameters mean that RABL could be used as the structural material for load-bearing situations. If ignoring the machining allowance, the bamboo utilization rate of the RABL was 1.72 times that of the rectangular element recombinant bamboo and the adhesive level of the RABL was 0.6 times that of the rectangular element recombinant bamboo. When considering the machining allowance, the bamboo utilization rate of the RABL was 1.8 times that of the rectangular element recombinant bamboo, and the adhesive volume of the RABL was 0.56 times that of the rectangular element recombinant bamboo, so RABL has obvious advantages.

Effects of carbon dioxide pneumoperitoneum on postoperative adhesion formation and oxidative stress in a rat cecal abrasion model

IntroductionIt is claimed that CO2 pneumoperitoneum (CP) is less adhesiogenic than laparotomy. Our aim in this study was to investigate the local oxidative stress responses and related adhesion formation resulting from exposure to CP. MethodsForty-five rats were randomised into six groups. Group 1 underwent laparotomy only; in group 2, 6 mmHg CP was performed for 60 min; in group 3, the same procedure was carried out using 12 mmHg CP; in group 4, laparotomy and cecal-peritoneal abrasion were performed; in group 5, 6 mmHg CP was performed for 60 min, followed by laparotomy and cecal-peritoneal abrasion; in group 6, the same procedure was carried out using 12 mmHg CP. Groups 1, 2 and 3 were sacrificed immediately and used only for biochemical examination. The other groups were sacrificed on the 14th postoperative day. ResultsThe total adhesion scores, thickness, quantity, extent and type of adhesions decreased steadily in groups 4, 5 and 6 (p < 0.05). The median values for neutrophil and monocyte infiltration, and for capillary and fibroblast proliferation decreased steadily in groups 4, 5 and 6 (p < 0.05). CAT, SOD and GSHPx levels decreased significantly in line with increasing pressure in groups 1, 2 and 3. SOD and GSHPx levels were similar in groups 4, 5 and 6, while CAT levels decreased with increasing pressure in groups 4, 5 and 6. ConclusionIt was found that CP is associated with less adhesion formation than laparotomy in the presence of similar antioxidant levels. The reduced adhesion formation is probably caused by a decreased inflammatory response.

Randomized experimental study to investigate the peritoneal adhesion formation of conventional monopolar contact coagulation versus noncontact argon plasma coagulation in a rat model

To investigate peritoneal adhesion formation of monopolar contact coagulation (MCC) versus noncontact argon plasma coagulation (APC) in a rat model. Randomized, controlled, single-blinded animal study. University laboratory. Sixteen female Wistar rats. Bilateral lesions were created on the abdominal wall with MCC and APC in a standard fashion. After 10days, the rats were euthanized to evaluate the peritoneal trauma sites. Adhesion incidence, quantity, and quality were scored 10days postoperatively and studied histopathologically. Average energy intake was 99.5 ± 7.39J for APC and 95.7 ± 9.62J for monopolar contact coagulation. Incidence of adhesion formation was 50.0% for noncontact APC and 85.4% for MCC. MCC induced significantly more vascular adhesions. Histological evaluation revealed no significant differences regarding average depth of lesions induced by APC and MCC. Both groups showed almost identical morphology of necrosis and granulation tissue formation. This study compares for the first time adhesion formation of MCC versus noncontact APC in a rat model. With a similar energy intake, contact coagulation induced a significantly higher rate of adhesion formation. APC-induced adhesions were significantly less vascularized compared with MCC adhesions. Besides the thermal effects of both coagulation methods, the direct mechanical contact of the MCC electrode with the highly sensitive peritoneum is thus determined to be a pivotal additional stimulus for adhesion formation.

Enhanced cellular responses to titanium coating with hierarchical hybrid structure

In this work, nano/micro hierarchical hybrid structured surface was prepared by fabricating a titania nanotube layer in plasma sprayed porous titanium coating (TC). In vitro human marrow stem cells (hMSCs) were employed for the evaluation of the biological properties of the anodized titanium coating with a hierarchical structure (HSTC). Significantly higher cell adhesion quantity (about 30% more) was found on the HSTC than that on the as-sprayed TC. The expressions of osteocalcin (OC) and osteopontin (OPN) for the HSTC were also detected to be about twice as high as those on the as-sprayed TC. The enhanced cell responses on the HSTC were explained by the improved protein adhesion resulted from the increased surface area and surface energy. Combining the advantages in the mechanical fixation and long-term stability of the plasma sprayed porous TC, the HSTC with a hierarchical structure may be a good candidate for hard tissue replacements, especially for load-bearing implants.

A Prospective Experimental Study to Investigate the Peritoneal Adhesion Formation of Argon Plasma Coagulation (APC) Versus a Novel Aerosol Plasma in a Rat Model

This is a prospective, randomized, controlled, single-blinded study to investigate peritoneal adhesion formation of standard argon plasma coagulation (APC) versus aerosol plasma coagulation in a rat model. Bilateral lesions were created on the abdominal wall of 16 female Wistar rats with standard and aerosol plasma coagulation APC energy in a standard fashion. After 10 days, the rats were killed humanely to evaluate the peritoneal trauma sites. Adhesion incidence, quantity, and quality were scored 10 days postoperatively and studied histopathologically. Average energy intake was 97.7 ± 3.1 J for APC and 93.8 ± 4.2 J for aerosol plasma coagulation. Incidence of adhesion formation was 74.2% for standard APC and 16.1% for aerosol plasma coagulation (P < .0001). Standard APC mainly results in dense adhesions. Histological evaluation revealed no significant difference with regard to the average depth of lesions created by APC and aerosol plasma coagulation (P = 0.21) at day 10; both groups showed an identical morphology of necrosis and granulation tissue formation. This study compares adhesion formation of standard APC versus aerosol plasma coagulation in a rat model. Standard APC produced significantly more adhesions. Aerosol plasma coagulation creates fewer adhesions, which are of lower grade, which seems to be achieved mainly by improved peritoneal conditioning in this animal model.