Acrylic Acid Research Articles

Poly acrylic acid patterning by electron beam lithography

Poly acrylic acid (PAA) is a polymer and a derivative of acrylic acid that is a superabsorbent, being able to absorb and retain water, and swell many times beyond its original volume. This property classifies it into a group of polymers called hydrogels. Hydrogels are being investigated in emerging applications such as drug delivery, biosensors, tissue engineering, wound healing bandages, and more. The ability to lithographically pattern hydrogel materials to specific dimensions at the micro and nanoscales can be very useful in devices and sensors. Limited work has been done on characterizing PAA for lithographic purposes, and so, this work investigates the ability to pattern PAA by electron beam lithography (EBL). PAA is interesting in that its carrier solvent, developer, and remover are all water alone, which may make it attractive for processes or materials that cannot tolerate solvents, acids, and bases used with other common EBL resists. PAA behaves as a negative tone resist with a relatively low base dose of 75 μC/cm2 at 100 kV acceleration voltage. The resolution is limited to 1.8 μm due to a low contrast of 1.29. However, PAA may still have many uses at that resolution where the positioning and dimension control of a hydrogel could be useful. Furthermore, PAA can successfully be used for pattern transfer with either a metal liftoff process or a silicon plasma etch.

Development of an Ionic Conductive Elastomer from the Photocopolymerization of a Ternary Polymerizable Deep Eutectic Solvent for Human Motions Sensing.

Polymerizable deep eutectic solvents (PDES) represent a novel class of ionic liquids characterized by the presence of polymerizable groups in their hydrogen-bond donor or acceptor components. Within the realm of flexible electronics, PDES is emerged as a promising material for the fabrication of sensors that exhibit both flexibility and stretchability. This research employs the UV-initiated photocopolymerization of a ternary PDES composed of choline chloride (ChCl), 2-hydroxyethyl acrylate (HEA), and itaconic acid (IA), to synthesize an ionic conductive elastomer (ICE) that boasts desirable comprehensive performances, which can be controlled by meticulously adjusting the ratios of these components. The fabrication process is streamlined and efficient, utilizing cost-effective and eco-friendly materials. This elastomer exhibits favorable ionic conductivity (1.70 × 10-2-5.45 × 10-2 S m-1), mechanical strength (0.48-1.21MPa stress at break, 395-701% elongation at break), adhesion capacity (49-120kPa adhesion strength), and sensing sensitivity toward human motions.

Radiation-induced nanogel engineering based on pectin for pH-responsive rutin delivery for cancer treatment.

This research investigates the formulation of a nanogel complex using pectin and poly(acrylic acid) (PAAc) to encapsulate rutin. The nanogel's pH-responsive behavior and its potential as a targeted drug delivery platform are investigated. The gamma irradiation-induced crosslinking mechanism is elucidated, highlighting its role in creating a stable three-dimensional network structure within the polymer matrix. Fourier transform infrared spectroscopy analysis sheds light on the molecular interactions within rutin and the nanogel-rutin complex. The pH-responsive behavior of the nanogel is explored, showcasing its ability to release rutin selectively in response to pH variations and displaying high physical and chemical stability. Transmission electron microscopy imaging provides visual insights into nanogel morphology and interactions. The cumulative drug content from the nanogel was 86.14 ± 2.61%. The pH-dependent release profile of the nanogel was examined, demonstrating selective rutin release in response to varying pH levels. Cytotoxicity studies were conducted against four human cancer cell lines-HepG2, A549, MCF-7, and HCT-116 showing significant reductions in IC50 values, indicating enhanced therapeutic efficacy. Additionally, molecular docking studies revealed strong binding interactions of rutin with VEGFR-2 and EGFRT790M. Our nanogel compound 5 significantly reduced the IC50 values for HepG2, A549, MCF-7, and HCT-116 cells by 58.19%, 81.29%, 71.81%, and 67.16%, respectively. Furthermore, it lowered the IC50 values for VEGFR-2 and EGFRT790M by 29.66% and 68.18%, respectively.

Cell Adhesion and Local Cytokine Control on Protein-Functionalized PNIPAM-co-AAc Hydrogel Microcarriers.

Achieving adequate cell densities remains a major challenge in establishing economic biotechnological and biomedical processes. A possible remedy is microcarrier-based cultivation in stirred-tank bioreactors (STBR), which offers a high surface-to-volume ratio, appropriate process control, and scalability. However, despite their potential, commercial microcarriers are currently limited to material systems featuring unnatural mechanical properties and low adaptability. Because matrix stiffness and ligand presentation impact phenotypical attributes, differentiation potential, and genetic stability, biotechnological processes can significantly benefit from microcarrier systems tailorable toward cell-type specific requirements. This study introduces hydrogel particles co-polymerized from poly(N-isopropylacrylamide) (PNIPAM) and acrylic acid (AAc) as a platform technology for cell expansion. The resulting microcarriers exhibit an adjustable extracellular matrix-like softness, an adaptable gel charge, and functional carboxyl groups, allowing electrostatic and covalent coupling of cell adhesive and cell fate-modulating proteins. These features enable the attachment and growth of L929 mouse fibroblast cells in static microtiter plates and dynamic STBR cultivations while also providing vital growth factors, such as interleukin-3, to myeloblast-like 32D cells over 20 days of cultivation. The study explores the effects of different educt compositions on cell-particle interactions and reveals that PNIPAM-co-AAc microcarriers can provide both covalently coupled and diffusively released cytokine to adjacentcells.

Cysteine Conjugation: An Approach to Obtain Polymers with Enhanced Muco- and Tissue Adhesion

The modification of polymers towards increasing their biocompatibility gathers the attention of scientists worldwide. Several strategies are used in this field, among which chemical post-polymerization modification has recently been the most explored. Particular attention revolves around polymer-L-cysteine (Cys) conjugates. Cys, a natural amino acid, contains reactive thiol, amine, and carboxyl moieties, allowing hydrogen bond formation and improved tissue adhesion when conjugated to polymers. Conjugation of Cys and its derivatives to polymers has been examined mostly for hyaluronic acid, chitosan, alginate, polyesters, polyurethanes, poly(ethylene glycol), poly(acrylic acid), polycarbophil, and carboxymethyl cellulose. It was shown that the conjugation of Cys and its derivatives to polymers significantly increased their tissue adhesion, particularly mucoadhesion, stability at physiological pH, drug encapsulation efficiency, drug release, and drug permeation. Conjugates were also non-toxic toward various cell lines. These properties make Cys conjugation a promising strategy for advancing polymer applications in drug delivery systems and tissue engineering. This review aims to provide an overview of these features and to present the conjugation of Cys and its derivatives as a modern and promising approach for enhancing polymer tissue adhesion and its application in the medical field.

Versatile synthesis of uniform mesoporous superparticles from stable monomicelle units.

Superstructures with architectural complexity and unique functionalities are promising for a variety of practical applications in many fields, including mechanics, sensing, photonics, catalysis, drug delivery and energy storage/conversion. In the past five years, a number of attempts have been made to build superparticles based on amphiphilic polymeric micelle units, but most have failed owing to their inherent poor stability. Determining how to stabilize micelles and control their superassembly is critical to obtaining the desired mesoporous superparticles. Here we provide a detailed procedure for the preparation of ultrastable polymeric monomicelle building units, the creation of a library of ultrasmall organic-inorganic nanohybrids, the modular superassembly of monomicelles into hierarchical superstructures and creation of novel multilevel mesoporous superstructures. The protocol enables precise control of the number of monomicelle units and the derived mesopores for superparticles. We show that ultrafine nanohybrids display enhanced mechanical antipressure performance compared with pristine polymeric micelles, and describe the functional characterization of mesoporous superstructures that exhibit excellent oxygen reduction reactivity. Except for the time (4.5 d) needed for the preparation of the triblock polystyrene-block-poly(4-vinylpyridine)-block-poly(ethylene oxide) PS-PVP-PEO or the polystyrene-block-poly(acrylic acid)-block-poly(ethylene oxide) (PS-PAA-PEO) copolymer, the synthesis of the ultrastable monomicelle, ultrafine organic-inorganic nanohybrids, hierarchical superstructures and mesoporous superparticles require ~6, 30, 8 and 24 h, respectively. The time needed for all characterizations and applications are 18 and 10 h, respectively.

Preparation of viscosity-reducing polycarboxylate superplasticizer (PCE) and its role in low water-to-cement ratio system

Owing to the low water-cement ratio (less than 0.25) of ultra-high-performance concrete (UHPC) materials, the system exhibits increased viscosity, diminished slurry flow, and challenges in pouring during the construction process, which compromise its workability. Consequently, the development of highly efficient viscosity-reducing polycarboxylate superplasticizer (PCE) is of paramount importance. In this study, we synthesized a series of viscosity-reducing polycarboxylate superplasticizers(JN-PCE) utilizing allyl polyethylene glycol ether (APEG), acrylic acid (AA), and sodium methallyl sulfonate (SMAS) as raw materials through the process of free radical polymerization. Fourier-transform infrared spectroscopy, nuclear magnetic resonance, gel permeation chromatography, and energy-dispersive X-ray spectroscopy were employed to characterize the materials. Subsequent evaluations of surface tension, fluidity, adsorption performance, and Marsh time demonstrated that these superplasticizers exhibited commendable dispersion and remarkable viscosity-reducing properties within a low water-cement ratio system. At a water-cement ratio of 0.18, the Marsh time of the JN-type PCE was reduced by 40% while maintaining the same fluidity, thereby underscoring the effective viscosity-reducing capabilities of the synthesized polycarboxylate superplasticizer.

Si anodes via dual strategies of coating Si with a rigid polymer and employing a polymer binder with improved mechanical properties

Si undergoes significant volume change over cycles which degrades the structural integrity and stability of the electrode. This volume change is the primary barrier to the commercialization of Si anodes, and it is more pronounced for Si particle sizes over 150 nm. In this study, a crosslinked polymer binder is developed using poly(acrylic acid-co-acrylamide) (PAAM) with enhanced elasticity compared to the widely used poly(acrylic acid). PAAM is further grafted with boronic acid and dopamine, yielding PAAM-B-D, a binder with improved adhesion due to its 3D crosslinked network. Additionally, 350-nm Si is coated with cyclized polyacrylonitrile (cPAN) and heat-treated to form a conjugated structure. The cPAN-coated Si (cSi) exhibits enhanced conductivity and mechanical stiffness and is used as an active material. The developed Si anode effectively combines cPAN-coated Si with the crosslinked network formed in the PAAM-B-D polymer for enhanced adhesion. The cSi@PAAM-B-D electrode sufficiently maintains its structural integrity and mitigates the Si volume change even with the large-sized 350-nm Si. The cSi@PAAM-B-D exhibits a high initial Coulombic efficiency of 86.5 %, at a Si mass loading of 2 mg cm−2. It also shows a capacity retention of 83.6 % and a high areal capacity of 3 mAh cm−2 after 50 cycles.

Triple-template surface imprinted magnetic polymers for wide-coverage extraction of steroid hormones from human serum.

In this study, novel triple-template magnetic nanospheres by surface imprinting, called triple-template magnetic molecularly imprinted polymers (tri-MMIPs), were prepared for the detection of steroid hormones in human serum. The polymers were constructed by Fe3O4 as support, estrone (E1), progesterone (PROG), and estradiol (E2) as triple templates, acrylic acid (AA) as functional monomer and ethylene glycol dimethacrylate (EGDMA) as cross-linker. The resulting tri-MMIPs were further characterized and applied as sorbents in human serum pretreatment. Coupled with ultra-high performance liquid chromatography-triple quadrupole tandem mass spectrometry (UHPLC-MS/MS) profiling after derivatization, 15 steroids (E1, 6-ketoE1, 4-OHE1, 16α-OHE1, DHEA, 4-MeOE1, PROG, PREG, 17-OHPROG, 7-DHE2, E2, 2-OHE2, 16-epiE3, E3, 2-MeOE2) were successfully quantified. The developed method exhibited a good recovery (78.9-114%) and low limit of quantitation (LLOQ, 5-10pg/mL), which indicates a great potential for application in the analysis of multiple steroid hormones in complex biological samples.

Localized Thermoresponsive Behavior in P(NIPAm‐co‐AAc) Copolymers: Structural Insights From Rheology and Small Angle X‐Ray Scattering

ABSTRACTStimuli‐responsive polymers stand out for their ability to respond to small environmental changes. One of the most representative thermo‐sensitive materials is poly(N‐isopropyl acrylamide) (PNIPAm), which presents reversible phase transitions close to the human body temperature. However, previous studies observed that the copolymerization of NIPAm with small quantities of different monomers like acrylic acid (AAc) results in copolymers with reduced or lost thermo‐responsivity. In this study, thermo‐sensitive PNIPAm, pH‐sensitive poly(acrylic acid) (PAAc), and various proportions of their copolymers P(NIPAm‐co‐AAc) were obtained by free radical polymerization and thoroughly characterized. Rheological and structural studies reveal the remaining thermosensitivity of the copolymers manifested at short molecular ranges. These alterations in short‐range interactions are observed in all samples containing NIPAm, and they are evidenced by changes in the fractality of their structure and flow index behavior of the Viscosity Ostwald–de Waele Model. Particularly, when the copolymer proportion of NIPAm/AAc is about 40/60, the Beaucage model reveals two structural levels, ~200 and ~10 nm. Furthermore, the model exhibits a thermal response of the lower‐size substructures, indicating possible segregation of NIPAm‐rich regions from copolymer chains. The evidence found in this work could contribute to the development of nanosystems, in which local thermoresponsive effects are sought, such as for active drug targeting.

Magnesium Fluoride Interlayers Enabled by Wet‐Chemical Process for High‐Performance Solid‐State Batteries

AbstractGarnet‐type solid‐state electrolytes (SSEs) exemplified by Li6.5La3Zr1.5Ta0.5O12 (LLZT) are chemically unstable when exposed to air, leading to the formation of impurities and poor wettability with Li metal. Herein, a protocol to address this Li/LLZT interface challenge is demonstrated by constructing a lithiophilic MgF2 nanofilm on the LLZT pellet. Specifically, a solution‐based process is developed for the surface engineering of LLZT, utilizing magnesium trifluoroacetate (MTF) as the molecular precursor while poly(acrylic acid) (PAA) as the coordinating agent in a sol‐gel process. It is demonstrated that a facile spin‐coating treatment followed by high‐temperature annealing reliably forms crack‐free MgF2 nanofilms with precise thickness control. Introduction an MgF2 interlayer transforms the LLZT pellet into a highly lithophilic, facilitating close contact with the lithium anode, thereby leading to a significantly reduced interfacial resistance from 1190 Ω cm2 to 6 Ω cm2. Such an interfacial engineering enables stable cycling of full batteries with high reversibility and rate capability using commercial LiFePO4 and LiNi0.83Co0.07Mn0.1O2 as cathodes. This study unfolds the possibility of a solution‐based method as a facile and scalable process for the construction of fluoride nanofilms, which is promising to address the critical interfacial challenges of solid‐state batteries (SSBs) to facilitate its practical applications.

High-Strength, Self-Healing Copolymers of Acrylamide and Acrylic Acid with Co(II), Ni(II), and Cu(II) Complexes of 4′-Phenyl-2,2′:6′,2″-terpyridine: Preparation, Structure, Properties, and Autonomous and pH-Triggered Healing

The utilization of self-healing polymers is a promising way of solving problems associated with the wear and tear of polymer products, such as those caused by mechanical stress or environmental factors. In this study, a series of novel self-healing, high-strength copolymers of acrylamide, acrylic acid, and novel acrylic complexes of 4′-phenyl-2,2′:6′,2″-terpyridine [Co(II), Ni(II), and Cu(II)] was prepared. A systematic study of the composition and properties of the obtained polymers was carried out using a variety of physicochemical techniques (elemental analysis, gel permeation chromatography (GPC), attenuated total reflectance Fourier transform infrared spectroscopy (ATR/FT-IR), ultraviolet-visible spectroscopy (UV-vis), small-angle X-ray scattering (SAXS), wide-angle X-ray scattering (WAXS), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), confocal laser scanning microscopy (CLSM), and tensile testing). All metallopolymer samples exhibit autonomous intrinsic healing along with maintaining high tensile strength values (for some samples, the initial tensile strength exceeded 100 MPa). The best values of healing efficiency are possessed by metallopolymers with a nickel complex (up to 83%), which is most likely due to the highest lability of the metal–heteroatom coordination bonds. The example of this system shows the ability to re-heal with negligible deterioration of the mechanical properties. The possibility of tuning the mechanical properties of self-healing films through the use of different metal ions has been demonstrated.

A Stretchable Conductive Material with High Fatigue Resistance for Strain Sensors.

Intrinsically stretchable conductive materials based on elastic substrates and conductive components play important roles in biomedical applications, such as exercise rehabilitation monitoring and disease prediction. A persistent challenge is to combine high fatigue resistance with excellent mechanical properties in stretchable conductive materials. Herein, we present a stretchable conductive material with both good fatigue resistance and high tensile properties (∼3170%) based on poly(acrylic acid)-phytic acid-trehalose-polypyrrole (denoted as PPTP). The as-prepared PPTP hydrogel electrode showed no obvious cracking or delamination after 400 loading and unloading cycles and maintained good electrical signal transmission function after 1000 cycles. We further collected stable signals for human motion and handwriting using the stretchable hydrogel electrode as a strain sensor, demonstrating the potential application of the PPTP stretchable hydrogel electrode in biomedicine.

Deciphering the Roles of Molecular Weight and Carboxyl Richness of Organic Matter on Their Adsorption onto Ferrihydrite Nanoparticles and the Resulting Aggregation.

The aggregation behavior of ferrihydrite nanoparticles (FNPs) can control the fate of associated aqueous contaminants, trace elements, and organic compounds. However, FNP aggregation is difficult to predict in the presence of organic matter (OM), given the heterogeneity in the OM properties. Five model OMs based on (poly)acrylic acid (PAA or AA) and polyethylene glycol with or without terminal carboxyl groups (PEG or PEGbis, respectively) were chosen to probe the influence of key OM properties─specifically, carboxyl richness and molecular weight (MW)─and the dominant mechanisms by which they influence OM adsorption onto FNPs and the resulting aggregation. For OMs with similar MWs, those with a higher carboxyl richness adsorbed more extensively onto FNPs: PAA2k > PEGbis > PEG. Meanwhile, for OMs with the same carboxyl richness, higher MW OMs adsorbed more: PAA25k > PAA2k > AA. Furthermore, the subsequent aggregation of FNPs was largely controlled by the adsorbed mass. OMs with negligible adsorption (i.e., PEG and AA) did not change the aggregation behavior of FNPs. For OMs with low carboxyl richness (PEGbis), accelerated aggregation occurred through a bridging effect with low adsorbed mass. For OMs with high carboxyl richness (PAA2k and PAA25k), aggregation was accelerated at moderate adsorbed OM masses by patch-charge attraction and was inhibited with high adsorbed OM mass due to steric repulsion. This study provided new insights into understanding and predicting the transport and fate of FNPs and natural organic matter (NOM) in natural environments with various NOM compositions.

Synthesis of long-chain polyester polymers and their properties as crude oil pour point depressant.

Using acrylic acid advanced ester and styrene as raw materials, the long-chain polyester polymer, polyacrylic acid advanced ester-styrene pour point depressant (P-PPD), was synthesized by molecular design, and its structure was characterized by infrared spectroscopy and nuclear magnetic resonance. In addition, this study experimentally investigated the effect of P-PPD on the phase equilibrium and induction time of natural gas hydrate inhibitors in deionized water (DW) and crude oil/water (O/W) systems, respectively. Polyvinylpyrrolidone (PVP) and mono ethylene glycol (EG) were selected as representatives of kinetic hydrate inhibitor (KHIs) and thermodynamic hydrate inhibitor (THIs), respectively. The results exhibit that P-PPD played a sight role in the phase equilibrium of hydrate, while the addition of P-PPD significantly prolonged the induction time of methane hydrate both in O/W + PVP, OW + EG and O/W + PVP + EG system, indicating that the addition of as-synthesized PPD has a synergistic inhibition effect on the nucleation ability of methane hydrate and can prevent hydrate from formatting during oil and gas transport process, and thus guarantee the flow assurance. The findings of this work will provide a data reference for the hybrid use of hydrate inhibitors and pour point depressants in oil and gas transport.

Novel Glycidyl Carbamate Functional Epoxy Resin Using Hydroxyl-Terminated Polybutadiene

Herein, a novel glycidyl carbamate functional epoxy resin (GCE) is synthesized by the additional reaction of the isocyanate group of tolylene diisocyanate (TDI) with the hydroxyl group of hydroxyl-terminated polybutadiene (HTPB) and glycidol. The successful synthesis of the GCE is confirmed by FT-IR and 1H NMR spectroscopy. Furthermore, a dual-curing adhesive system is developed using acrylic acid and trimethylolpropane triacrylate with varying GCE contents, and its adhesive performance is assessed by testing adhesive strength, pencil hardness, and surface energy. As a result, the dual-cure adhesive containing 0.2 mol of GCE demonstrates an impressive adhesive strength of 11.1 MPa, a pencil hardness of B, and surface energy comparable to that of standard polycarbonate film.

A Dry Patch with In Situ Solid-to-Gel Transformation for All-in-One Skin Wound Care.

Hydrogel-based dressing materials offer significant potential in expediting skin wound healing. Nevertheless, they face several challenges: poor adhesion to wound tissues, difficulties in preservation under ambient conditions, and limited multifunctionality to support all wound healing stages. In this work, a dry patch is designed to address these persistent issues by featuring an in situ solid-to-gel transformation and Janus wet tissue adhesiveness. The HGP patch integrates a wet adhesive layer combining dopamine-conjugated hyaluronic acid (HD) and poly(acrylic acid) (PAA), a drug-loading layer comprising gelatin (Gel), and a nonadhesive gelation layer of poly(vinyl alcohol) (PVA) and sodium alginate (SA). This hierarchical structural design confers exceptional wound adhesion, hemostatic capabilities, and antibacterial and antioxidant activities, as well as immune regulatory properties. These attributes collectively support accelerated skin wound healing, particularly in cases complicated by bacterial infections. This research charts an approach to engineer hydrogel-based wound dressings through on-site hydrogel formation, thus advancing the treatment of wounds afflicted with complex infections.

Fabrication and Evaluation of Polyacrylate Nanocomposites Embedded With Metal Oxides as Enhanced Multipurpose Nanocarriers for Long‐Term Anti‐Inflammatory and Amazing Antimicrobial Properties

ABSTRACTThe design of super‐antimicrobially active multipurpose nanocarriers as polymeric nanocomposites embedded with metal oxides with sustained drug release is beneficial in medical treatment for controlling inflammation and targeting a wide range of pathogenic microorganisms. Brilliant metal oxide nanoparticles (MOx) involving selenium dioxide, titanium dioxide, and vanadium pentoxide were well prepared in good yields, and their morphologies and structures were specified. Then they were embedded in copolymeric nanocomposites through in situ microemulsion polymerization of (E)‐2‐cyano‐N‐cyclohexyl‐3‐(dimethylamino)acrylamide (CHAA) with methyl methacrylate (MMA), dimethylaminoethyl methacrylate (DMAEMA), and acrylic acid (AA). In addition, ibuprofen was then loaded into the synthesized polymers and their nanocomposites to achieve high drug entrapment efficiency EE%, and its release behavior was studied in various simulated fluids. The produced drug‐loaded polymers and their nanocomposites were characterized using Fourier‐transform infrared spectroscopy (FT‐IR), transmission electron microscope (TEM), X‐ray diffraction (XRD), and thermogravimetric analysis (TG). Well‐defined nanospheres of polymeric‐metal oxide nanocomposites were generated in a size range of 50 nm, with ibuprofen loaded at a high encapsulation efficiency of approximately 97%. In vitro drug release was inspected for the polymer and its nanocomposites revealing that the presence of metal oxide nanoparticles resulted in prolonged and sustained release behavior for wound dressing. The antimicrobial study based on the zone of inhibition against various pathogenic microorganisms showed excellent activity against Bacillus cereus, Staphylococcus aureus, Escherichia coli, Helicobacter pylori, and Candida albicans. These findings validate the potential of these nanocomposites to serve as a viable upcoming antimicrobial agent for the treatment of human ailments.

Fibrous foes: First report on insidious microplastic contamination in dietary fiber supplements

Regular consumption of health supplements to balance dietary intake has gained popularity worldwide. One such supplement that has gained popularity among consumers is dietary fibers. Microplastic (MPs) contamination in various food products is being reported worldwide. However, there is a paucity of understanding of the occurrence of MPs in dietary supplements. This study addresses this gap by investigating the degree of MPs contamination in dietary fiber supplements. Nine commonly consumed (powder and gummy-based) over-the-counter dietary fiber supplements in Australia were tested in this study. Microscopic examination revealed the presence of MPs fibers and fragments in all the tested products. Further categorization showed that MPs particles were of various colours, including black, blue, red, green, and white. The order of polymer abundance was Polyamide > Polydiallyl Phthalate > polyethylene polypropylene diene > Polyurethane = Polyethylene terephthalate > Polyethylene = Ethylene acrylic acid copolymer. Among the supplements, powder-based samples had higher MPs (at the adult dosage suggested by the manufacturer) than gummy-based product. The average predicted ingestion of microplastics from these supplements (all nine samples) was 5.89 ± 2.89 particles day−1. The dietary exposure for children and adults ranged from 0.1–0.48 and 0.18–4.08 particles day−1, respectively. Based on the microplastic contamination factor (MCF), among the nine samples tested, 69.81% exhibited a moderate level, while 20.76% showed a significant level of microplastic contamination. The polymer risk index (pRi) indicates products with very high and high-risk categories. The possible sources of MPs contamination in the products were studied. To our knowledge, this is the first study to record and quantify the presence of MPs in dietary fiber supplements, which is a direct source of MPs exposure to humans via., ingestion.

PH-sensitive polymeric hydrogels coated with cobalt ferrite nanoparticles for combined drug delivery as controlled release carriers: fabrication and in-vitro estimation

In this investigation, we produced pH-responsive hydrogels for the controlled release of drugs by graft copolymerizing Gum ghatti and acrylic acid (AA) in an aqueous medium. N, N′-methylene-bis-acrylamide (MBA) and ammonium persulphate (APS) served as cross-linkers during the synthesis process. Our research explores the integration of cobalt ferrite (CoFe2O4) magnetic nanoparticles (CFMNPs) in delivering a combination drug comprising metformin hydrochloride and sodium diclofenac. The diverse applications of CoFe2O4 nanoparticles have driven the exploration of innovative and environmentally sustainable production methods. The development of novel materials for nanoparticle synthesis adheres to the principles of “Green Chemistry” through a co-precipitation technique. Characterization of the cross-linked hydrogels involved Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) analyses. In vitro drug release kinetics were observed under physiological conditions using Ultraviolet–Visible Spectroscopy. The drug-loaded Gg-cl-poly(AA)/CoFe2O4 hydrogels exhibited a sustained drug release profile over 24 h, with significant release occurring at a pH of 4. To comprehend the drug release mechanism, we employed kinetic modeling, encompassing Zero order, First order, Higuchi model, Hixson-Crowell model, and Korsmeyer-Peppas model, for all developed hydrogels. The findings indicated that the drug release mechanism from the hydrogels followed the Korsmeyer-Peppas model. The study concludes that the developed hydrogel offers a promising solution for the controlled administration of metformin hydrochloride and diclofenac sodium.Graphical