Plasma Polymerization Of Acrylic Acid Research Articles

Anti-fogging surfaces produced by plasma polymerization of acrylic acid

In this paper, plasma enhanced chemical vapor deposition (PECVD) of acrylic acid (AA) was employed as a one-step and solvent-free technique to prepare durable organic anti-fogging coatings on mirror and glass surfaces. The effects of important PECVD parameters including substrate temperature and plasma power on the deposition kinetics, as well as on the structural and morphological properties of the as-deposited films were investigated. Employing a low substrate temperature (5 °C) and a high plasma power (30 W) combination resulted in the highest observed deposition rate of 27.7 nm/min. Fourier-transform infrared (FTIR) spectroscopy showed high structural resemblance between PECVD-PAA and reference poly(acrylic acid) (PAA). The PAA-deposited surfaces showed excellent and durable anti-fogging performance without any loss in their optical transparencies. Successive antifogging tests showed that the PAA thin film exhibited high functional durability without delamination, indicating that it can be used in real-world applications.

Acrylic acid plasma polymerization and post-plasma ethylene diamine grafting for enhanced bone marrow mesenchymal stem cell behaviour on polycaprolactone nanofibers

Electrospun polycaprolactone (PCL) nanofibers (NFs) have been extensively researched for tissue engineering purposes, despite their hydrophobic surface properties which compromise their cell interactivity. To enhance this interactivity, within this study, the surface of PCL NFs was first modified by acrylic acid plasma polymerization. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) confirmed that the plasma process did not damage the NFs. Water contact angle (WCA) and zeta potential measurements showed a significant wettability increase and surface charge decrease, respectively. X-ray photoelectron spectroscopy (XPS) confirmed that the NFs were coated with a plasma polymer containing O-based functional groups, which could be related to the aforementioned changes in surface wettability and charge. Additionally, a post-plasma grafting step of ethylene diamine on the surface carboxylic acid groups was performed to investigate the influence of COOH-groups on bone marrow mesenchymal stem cell (BMST) adhesion and proliferation. WCA, zeta potential and XPS measurements confirmed the successful conversion of carboxylic acid into primary amine groups, while SEM indicated that the NF morphology did not change upon the reaction. PCL NFs subjected to this post-plasma grafting evoked the best BMST behaviour, indicating that minor changes in the surface chemistry can have a significant effect on cell-biomaterial interactions.

Improving the effects of plasma polymerization on carbon fiber using a surface modification pretreatment

Plasma and electrochemical treatments of carbon fibers for enhanced properties are often presented in opposition to each other. This work demonstrates the combination of these methodologies through the electrochemical attachment of nitroaryl moieties to the surface of the carbon fiber, prior to the deposition of plasma polymerized acrylic acid to the surface. Notably, the tensile strength of fibers having undergone both surface modification and plasma polymerization showed a significant increase (3.76 ± 0.08 GPa), relative to control fibers (3.31 ± 0.11 GPa), while plasma polymerization alone showed no change (3.39 ± 0.09 GPa). Additional benefits resulting from both treatments were observed when determining the fiber-to-matrix adhesion. Plasma polymerization of acrylic acid alone returned a 49% increase in interfacial shear strength (IFSS) compared to control (28.3 ± 1.2 MPa vs 18.9 ± 1.2 MPa, respectively). While the presence of nitrophenyl groups on the fiber prior to polymerization conferred an additional 24% improvement over plasma polymerization alone and a 73% improvement relative to control fibers (32.7 ± 0.5 MPa vs 18.9 ± 1.2 MPa, respectively). Finally, we present the first comparison of scanning electron microscopy (SEM) and helium ion microscopy (HIM) to visualize polymers on the carbon fiber surface. HIM shows a clear advantage over conventional SEM in visualizing non-conductive coatings on carbon fibers. Analysis of the samples by X-ray photoelectron spectroscopy (XPS) confirmed the desired chemistry had been imparted onto the surface, consistent with the plasma-polymerized acrylic acid coating and presence of nitro-aryl moieties.

Plasma Polymerization of Acrylic Acid for the Tunable Synthesis of Glassy and Carboxylated Nanoparticles.

Polymer nanoparticles (NPs) can be highly attractive in numerous applications, including biomedicine, where the use of inorganic matter may be detrimental for living tissues. In conventional wet chemistry, polymerization and functionalization of NPs with specific chemical groups involves complex and often numerous reactions. Here, we report on a solvent-free, single-step, low-temperature plasma-based synthesis of carboxylated NPs produced by the polymerization of acrylic acid under the conditions of a glow discharge. In a monomer-deficient regime, the strong fragmentation of monomer molecules by electron impact results in the formation of 15 nm-sized NPs with <1% retention of the carboxyl groups. In an energy-deficient regime, larger 90 nm-sized NPs are formed with better retention of carboxyl groups that reaches 16%. All types of NPs exhibit a glass transition above room temperature, which makes them highly stable in an aqueous environment with no dissolution or swelling. The NPs are also found to degrade thermally when heated above 150 °C, with a decrease in the mean NP size but with retention of the chemical composition. Thus, plasma polymerization proves to be a versatile approach for the production of polymer NPs with a tunable size distribution, chemical composition, and physical properties.

Nanophase‐separated poly(acrylic acid)/poly(ethylene oxide) plasma polymers for the spatially localized attachment of biomolecules

AbstractCarboxyl‐enriched nanoparticles are produced by the plasma polymerization of acrylic acid (ppAA NPs), whereas plasma‐assisted vapor‐phase deposition is used to prepare thin films of poly(ethylene oxide) (ppPEO). Sequential depositions generate phase‐separated coatings. The ppAA NPs are found to be in a glassy state, whereas thin films of ppPEO are found to be in a rubbery state. When immersed into a solution of lysozymes, the ppPEO absorbs water, which results in the dissociation of the carboxyls on the ppAA NP surface. Negatively charged carboxyls attract positively charged lysozymes. The ppPEO surface in between the NPs resists the accumulation of the protein, leading to the spatially localized adsorption of lysozymes only on the spots where the ppAA NPs are located.

Carboxyl-Functionalized Nanoparticles Produced by Pulsed Plasma Polymerization of Acrylic Acid.

Carboxyl-enriched and size-selected polymer nanoparticles (NPs) may prove to be very useful in biomedical applications for linker-free binding of biomolecules and their transport to cells. In this study, we report about the synthesis of such NPs by low-pressure low-temperature pulsed plasma polymerization of acrylic acid. Gas aggregation cluster source was adapted to operate plasma with a constant pulse period of 50 μs and with varying duty cycle. The NPs were produced with the size ranging from 31 ± 5 to 93 ± 14 nm and with retention of the carboxyl groups ranging from 4.0 to 12.0 atom %. Two regimes of the NP formation were identified. In the large duty cycle regime, the NP growth was interfered with by positive ion bombardment which resulted in the ion-driven detachment of the carboxyl species and in the formation of carboxyl-deficient NPs. In the small duty cycle regime, the NP growth was accompanied by the radical-driven chain propagation with the attachment of intact monomer molecules. Improved efficacy of the monomer retention resulted in increased concentration of the carboxyl groups.

Oxygen and Acrylic Acid Plasma Treatment on Titanium Mesh for Improving the Hydroxyapatite Formation.

Customized titanium (Ti) meshes were treated with O2 plasma and acrylic acid plasmapolymerization (PPAAc). The optimum conditions for PPAAc were as follows: 20 W, 15 mTorr, and 5 min. Hydroxyapatite formation increased in Ti meshes treated with O2 and PPAAc compared with that in untreated Ti meshes. Moreover, MC3T3-E1 cells exhibited improved cell spreading, attachment, proliferation in PPAAc treated Ti mesh than in untreated Ti mesh. This result revealed that O2 and PPAAc surface treatment on Ti mesh was potential tool for improving the bone formation on the Ti mesh clinically application.

Evaluation of mechanism of cold atmospheric pressure plasma assisted polymerization of acrylic acid on low density polyethylene (LDPE) film surfaces: Influence of various gaseous plasma pretreatment

Owing to its exceptional physiochemical properties, low density poly ethylene (LDPE) has wide range of tissue engineering applications. Conversely, its inadequate surface properties make LDPE an ineffectual candidate for cell compatible applications. Consequently, plasma-assisted polymerization with a selected precursor is a good choice for enhancing its biocompatibility. The present investigation studies the efficiency of plasma polymerization of acrylic acid (AAC) on various gaseous plasma pretreated LDPE films by cold atmospheric pressure plasma, to enhance its cytocompatibility. The change in chemical composition and surface topography of various gaseous plasma pretreated and acrylic deposited LDPE films has been assessed by X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The changes in hydrophilic nature of surface modified LDPE films were studied by contact angle (CA) analysis. Cytocompatibility of the AAC/LDPE films was also studied in vitro, using RIN-5F cells. The results acquired by the XPS and AFM analysis clearly proved that cold atmospheric pressure (CAP) plasma assisted polymerization of AAC enhances various surface properties including carboxylic acid functional group density and increased surface roughness on various gaseous plasma treated AAC/LDPE film surfaces. Moreover, contact angle analysis clearly showed that the plasma polymerized samples were hydrophilic in nature. In vitro cytocompatibility analysis undoubtedly validates that the AAC polymerized various plasma pretreated LDPE films surfaces stimulate cell distribution and proliferation compared to pristine LDPE films. Similarly, cytotoxicity analysis indicates that the AAC deposited various gaseous plasma pretreated LDPE film can be considered as non-toxic as well as stimulating cell viability significantly. The cytocompatible properties of AAC polymerized Ar + O2 plasma pretreated LDPE films were found to be more pronounced compared to the other plasma pretreated AAC/LDPE films.

Cell Proliferation on Macro/Nano Surface Structure and Collagen Immobilization of 3D Polycaprolactone Scaffolds.

In this study, 3D polycaprolactone (PCL) scaffolds were fabricated by 3D printing technique. The macro/nano morphology of, 3D PCL scaffolds surface was etched with oxygen plasma. Acrylic acid (AA) plasma-polymerization was performed to functionalize the macro/nano surface with carboxyl groups and then collagen was immobilized with plasma-polymerized 3D PCL scaffolds. After O2 plasma and AA plasma-polymerization, contact angles were decreased. The FE-SEM and AFM results showed that O2 plasma is increased the surface roughness. The MTT assay results showed that proliferation of the M3CT3-E1 cells increased on the oxygen plasma treated and collagen immobilized 3D PCL scaffolds.

Flow Fields during Formation of W/O and O/W Emulsions using μPIV

The current work investigates two phase flow visualization in a micro channel using micron resolution particle image velocimetry (μPIV). Droplets of both oil-in-water and water-in-oil emulsions were generated in a T-shaped PDMS micro fluidic device and the corresponding flow fields were measured down-stream in the divergent section of the device. The oil-in-water emulsions were formed in a hydrophilically modified PDMS micro channel using plasma polymerization of acrylic acid. To obtain the velocity fields in both types of emulsions, fluorescent particles of 0.86 m size were added into the dispersed water phase in the case of water-in-oil emulsions, and in the continuous water phase in the case of oil-in-water emulsions. The phenomena of flow behavior within the droplets and around the droplets were investigated in detail in a diverging micro channel

Plasma polymerization of acrylic acid onto polystyrene by cyclonic plasma at atmospheric pressure

The cyclonic atmospheric-pressure plasma is developed for chamberless deposition of poly(acrylic acid) film from argon/acrylic acid mixtures. The photoemission plasma species in atmospheric-pressure plasma polymerization was identified by optical emission spectroscopy (OES). The OES diagnosis data and deposition results indicated that in glow discharge, the CH and C2 species resulted from low-energy electron-impact dissociation that creates deposition species, but the strong CO emission lines are related to nondeposition species. The acrylic acid flow rate is seen as the key factor affecting the film growth. The film surface analysis results indicate that a smooth, continuous, and uniform surface of poly(acrylic acid) films can be formed at a relatively low plasma power input. This study reveals the potential of chamberless film growth at atmospheric pressure for large-area deposition of poly(acrylic acid) films.

Reaction of CO2Gas with (radicals in) Plasma-Polymerized Acrylic Acid (and Formation of COOH-Rich Polymer Layers)

In contrast to most of the existing literature on plasma polymerization of acrylic acid (AA), not only the chemical structure and film thickness of the deposits were studied, but also a new way to obtain COOH-rich surfaces were studied. This is an important aspect when applying the obtained coatings for biomedical and electronics applications. Therefore, acrylic acid/CO2 polymer films with a thickness of ca. 150 nm were deposited in the pulsed plasma regime onto polyethylene and aluminum. Their structure–property relationships were studied in dependence on the mixture ratio of acrylic acid monomer and CO2 gas. The influence of the CO2 gas on the regularity and functionality of plasma-deposited poly(acrylic acid) (PAA) was studied in detail using bulk-sensitive (FTIR) as well as surface-sensitive methods, such as X-ray photoelectron spectroscopy. Results obtained show, in presence of a small amount of CO2 gas within the acrylic acid plasma, a structure of PAA with high concentration of COOH groups was estimated. A polymer network is obtained with an increasing abundance of branched groups for AA/CO2 with increasing CO2 gas in the mixture.

Immobilization and controlled release of drug using plasma polymerized thin film

In this study, plasma polymerization of acrylic acid was employed to immobilize drug and control its release. Doxorubicin (DOX) was immobilized covalently on the glass surface deposited with plasma polymerized acrylic acid (PPAAc) thin film containing the carboxylic group. At first, the PPAAc thin film was coated on a glass surface at a pressure of 1.33Pa and radio frequency (RF) discharge power of 20W for 10min. DOX was immobilized on the PPAAc deposition in a two environment of phosphate buffer saline (PBS) and dimethyl sulfoxide (DMSO) solutions. The DOX immobilized surface was characterized by scanning electron microscope, atomic force microscope and attenuated total reflection Fourier transform infrared spectroscopy. The DOX molecules were more immobilized in PBS than DMSO solution. The different immobilization and release profiles of DOX result from the solubility of hydrophobic DOX in aqueous and organic solutions. Second, in order to control the release of the drug, PPAAc thin film was covered over DOX dispersed layer. Different thicknesses and cross-linked PPAAc thin films by adjusting deposition time and RF discharge power were covered on the DOX layer dispersed. PPAAc thin film coated DOX layer reduced the release rate of DOX. The thickness control of plasma deposition allows controlling the release rate of drug.

Underwater discharge plasma-induced coating of poly(acrylic acid) on polypropylene fiber

An underwater diaphragm discharge generated at atmospheric pressure by high voltage pulses was used for plasma polymerization of acrylic acid and simultaneously for the deposition of polymer coating on polypropylene multifilament fibers. The deposition process was monitored by Fourier transform infrared spectroscopy in combination with scanning electron microscopy. Possible schemes of polymerization are suggested also.

Surface functionalisation of polypropylene hernia-repair meshes by RF-activated plasma polymerisation of acrylic acid and silver nanoparticles

Hernia diseases are among the most common and diffuse causes of surgical interventions. Unfortunately, still nowadays there are different phenomena which can cause the hernioplasty failure, for instance post-operative prostheses displacements and proliferation of bacteria in the surgical site. In order to limit these problems, commercial polypropylene (PP) and polypropylene/Teflon (PP/PTFE) bi-material meshes were surface functionalised to confer adhesive properties (and therefore reduce undesired displacements) using polyacrylic acid synthesized by plasma polymerisation (PPAA). A broad physico-chemical and morphological characterisation was carried out and adhesion properties were investigated by means of atomic force microscopy (AFM) used in force/distance (F/D) mode. Once biomedical devices surface was functionalised by PPAA coating, metallic silver nanoparticles (AgNPs) with antimicrobial properties were synthesised and loaded onto the polymeric prostheses. The effect of the PPAA, containing carboxylic functionalities, adhesive coating towards AgNPs loading capacity was verified by means of X-ray photoelectron spectroscopy (XPS). Preliminary measurement of the Ag loaded amount and release in water were also investigated via inductively coupled plasma atomic emission spectroscopy (ICP-AES). Promising results were obtained for the functionalised biomaterials, encouraging future in vitro and in vivo tests.

Amine functionalized nanodiamond promotes cellular adhesion, proliferation and neurite outgrowth

In this study, we report the production of amine functionalized nanodiamond. The amine functionalized nanodiamond forms a conformal monolayer on a negatively charged surface produced via plasma polymerization of acrylic acid. Nanodiamond terminated surfaces were studied as substrates for neuronal cell culture. NG108-15 neuroblastoma-glyoma hybrid cells were successfully cultured upon amine functionalized nanodiamond coated surfaces for between 1 and 7 d. Additionally, primary dorsal root ganglion (DRG) neurons and Schwann cells isolated from Wistar rats were also successfully cultured over a period of 21 d illustrating the potential of the coating for applications in the treatment of peripheral nerve injury.

Formation of bone-like apatite on plasma-carboxylated poly(etheretherketone) surface

Poly(etheretherketone) (PEEK) has attracted considerable research interest as a biomaterial for orthopedic or dental implants due to its bone-like stiffness and reasonable biocompatibility. However, PEEK is naturally bioinert, leading to limited biomedical applications, especially when direct bone-implant integration is desired. In this investigation, carboxyl groups were introduced on PEEK sheet surface using plasma polymerization of acrylic acid (AAc) for the first time. XPS confirmed the presence of carboxyl groups. When placed in stimulated body fluid for 4 weeks, apatite formed uniformly on plasma-carboxylated PEEK sample surface. SEM, EDS and FTIR results confirmed the formation of bone-like apatite. This study provides a simple method to enhance the bioactivity of PEEK without sacrificing its excellent mechanical properties.

Surface modification of cellulosic substrates via atmospheric pressure plasma polymerization of acrylic acid: Structure and properties

Abstract Surface chemical modification of cellulose-based substrates has been carried out by atmospheric pressure plasma enhanced chemical vapor deposition (AP-PECVD) of acrylic acid. The structure/properties relationship of the samples was studied as a function of the plasma experimental conditions. Acrylic acid monomer/helium ratio and treatment speed clearly influences the wettability properties of the paper substrate: advancing contact angle values were reduced to the half if compare to non-treated paper. Surface morphology of the films did not greatly vary at short polymerization times but fibers were covered by a poly(acrylic acid) film at longer times. FTIR and XPS techniques allowed detecting the retention of carboxylic acid groups/moieties. The possibility to quickly design architectures with tunable carboxylic functions by modifying the plasma processing parameters is shown.

Improving stability of TiO2 particles in water by RF-plasma polymerization of poly(acrylic acid) on the particle surface

The stability of TiO2 particles in water was increased through plasma polymerization of acrylic acid (AA) onto the particles surface. The polymerization was carried out directly upon TiO2 powder by using two radiofrequency (RF) plasma reactors: one inductively coupled and another capacitively coupled. In both cases, a cross-linked polyacrylic acid (PAA) film was formed on TiO2 particles surface, which was characterized by Energy Dispersive Spectroscopy (EDS), Fourier-transformed infrared spectroscopy, (FTIR), Raman Spectroscopy, and X-ray photoelectron spectroscopy (XPS). The stability of the PAA-coated TiO2 particles was determined by their precipitation in water. It was found that a moderate plasma treatment effectively improved the stability of PAA-coated TiO2 particles. At low levels of AA polymerization, the TiO2 particles surface was not modified enough to improve their stability in water; on the other hand, a high degree of AA polymerization led to the formation of large agglomerates, induced by the PAA film, and these particles were not stable. As expected, the particle size and the Z-potential of the PAA-coated particles determined their stability in water. Under the optimum operating conditions of this study, the treated TiO2 particles showed stability as good as that of TiO2 particles modified with a dispersant.

Plasma treated high-density polyethylene (HDPE) medpor implant immobilized with rhBMP-2 for improving the bone regeneration

We investigate the bone generation capacity of recombinant human bone morphogenetic protein-2 (rhBMP-2) immobilized Medpor surface through acrylic acid plasma-polymerization. Plasma-polymerization ...