Acoustic Logging Research Articles

Evaluation of cement density utilizing through-casing X-Ray logging method

In the evaluation of cementing quality, quantitatively assessing cement density is crucial along with identifying the cementation degree at the interface using acoustic logging. While the 137Cs-based formation density logging method is well-suited for density calculation, its reliance on open-hole environmental measurements poses challenges when inspecting cement density. This work focuses on the quantitative calculation of cement density while considering the radioactive hazards to the environment caused by 137Cs source. The proposed approach utilizes a measurement system consisting of an X-Ray source and four gamma detectors. The gamma spectrum characteristics of each detector are analyzed, and the energy spectrum recorded by each detector is distinguished by different energy windows. A forward model is established to relate the gamma counts of each energy window to the formation and cement parameters. By employing a regularized Newton’s method based on optimization technique, cement density can be calculated with a controllable error margin of within 0.015 g/cm3. Furthermore, even though X-Ray detection has lower sensitivity to formation parameters compared to 137Cs, this method is capable of estimating formation density. Overall, the proposed approach enables the quantitative calculation of cement density and semi-quantitative calculation of formation density, therefore is of significance to the comprehensive evaluation of cementing quality.

Analysis of the reservoir properties of rocks of the Lower Kura depression (Azerbaijan)

The article analyzes the features characterizing the Lower Kura depression (LKD). A number of hydrocarbon deposits have been discovered in this oil and gas region. The Kalmas underground gas storage facility, which has the largest volume in Azerbaijan, is also located in this area. In the LKD, all PS formations can be traced throughout the entire well section. The reservoir properties of the rocks were considered to study the features of the area. In order to study the reservoir properties in the well section, the field applies data obtained by using a complex of well logging (WL) methods (laterolog, spontaneous potential logging, induction logging, gamma logging, neutron logging, acoustic logging) and analyses of rock samples. The graphs were constructed to evaluate the relationship between petrophysical parameters (porosity, permeability, etc.) determined in the rocks involved in the well sections of the object of research. In the article, maps of porosity distribution, permeability and permeability of sandy siltstone rocks and fractions greater than 0.1 of the Productive Series of the South-Eastern Gobustan and Baku Archipelago, which are part of the Low Kura Depression, are plotted and analysed. Plots showing the porosity distribution of the Low Kura Depression by depth were also constructed and some results were obtained. Based on reservoir properties, the region is divided into 6 groups, and in each group intermediate values of the porosity and permeability coefficient are determined. In general, the porosity coefficient ranges within 5-25%, permeability – 1-250 mD. The reservoir properties of rocks vary over area from worse to better. The capacitance-filtration properties of rocks were studied. The rock samples analysed identified rocks with good and low reservoir characteristics. To study the variation in the determining factors, maps of the distribution of reservoir properties indicators (fractions greater than 0.1 mm; porosity and permeability in sand-siltstone-containing rocks) were compiled by area and their causes were determined by comparison with other oil and gas fields. It was found that with distance from the mouth of the Kura River (towards the right and left banks), the reservoir properties of the rocks deteriorate. This is due to an increase in the amount of clay in rocks. It is also clarified that the change in porosity coefficient does not depend on depth. The content of sand-siltstone composition in the rocks along the section is 20-50%.

Determination and Application of Stress States Based on Finite Element Techniques: A Case Study of the Longmaxi Formation in the Luzhou Block, Sichuan Basin.

Knowledge of the present-day in situ stress field (PIS) has important theoretical and practical significance for shale gas exploration and development. The Wufeng-Longmaxi Formation in the Luzhou Block serves as the main reservoir of marine shale production in southern China. However, there is no clear understanding of PIS in the Luzhou area, which leads to a series of production problems. To investigate the PIS of deep shale reservoirs in Luzhou, experimental and finite element methods (FEMs) were used. Data obtained from imaging logging data, well deviation data, multipole array acoustic logging (XMAC), and world stress map were used to determine the orientation of the horizontal maximum principal stress (S Hmax). Additionally, acoustic emission experiments were employed to determine the magnitude of three principal stresses. Based on FEM, with the stress of a single well as a constraint, a three-dimensional (3D) stress field model was developed. The results show that the orientation of S Hmax varies from 90 to 120 °E. Further, there are significant differences in stress regimes across the region, with strike-slip/reverse faulting stress regime (S Hmax > S v ≈ S hmin) in the northern region and strike-slip stress regime in the southern region (S Hmax > S v > S hmin). In addition, geomechanical evaluations of wellbore stability and natural activation of fractures were performed. The Luzhou Block mainly develops two groups of natural fractures (NE-SW trending and NW-SE trending), with NW-SE trending being the dominant fracture development orientation. During the fracturing operation, a pore pressure increment larger than 50 MPa is conducive to maintaining a high opening ratio of the reservoir and improving the gas production efficiency. Horizontal wells drilled in the direction of maximum horizontal principal stress in the Wufeng-Longmaxi Formation reduce the probability of wellbore instability. The research results provide a reference for the effective development of deep shale gas reservoirs in southern Sichuan.

Multiscale Characterization of Fractures and Analysis of Key Controlling Factors for Fracture Development in Tight Sandstone Reservoirs of the Yanchang Formation, SW Ordos Basin, China

Tight sandstone reservoirs, despite their low porosity and permeability, present considerable exploration potential as unconventional hydrocarbon resources. Natural fractures play a crucial role in hydrocarbon migration, accumulation, and present engineering challenges such as late-stage reformation in these reservoirs. This study examines fractures in the seventh member of the Triassic Yanchang Formation’s tight sandstone within the Ordos Basin using a range of methods, including field outcrops, core samples, imaging and conventional logging, thin sections, and scanning electron microscopy. The study clarifies the characteristics of fracture development and evaluates the relationship between dynamic and static rock mechanics parameters, including the calculation of the brittleness index. Primary factors influencing fracture development were quantitatively assessed through a combination of outcrop, core, and mechanical test data. Findings reveal that high-angle structural fractures are predominant, with some bedding and diagenetic fractures also present. Acoustic, spontaneous potential, and caliper logging, in conjunction with imaging data, enabled the development of a comprehensive probabilistic index for fracture identification, which produced favorable results. The analysis identifies four key factors influencing fracture development: stratum thickness, brittleness index, lithology, and rock mechanical stratigraphy. Among these factors, stratum thickness is negatively correlated with fracture development. Conversely, the brittleness index positively correlates with fracture development and significantly influences fracture length, aperture, and linear density. Fractures are most prevalent in siltstone and fine sandstone, with minimal development in mudstone. Different rock mechanics layer types also impact fracture development. These insights into fracture characteristics and controlling factors are anticipated to enhance exploration efforts and contribute to the study of similar unconventional reservoirs.

Simulation and Optimization of Transmitting Transducers for Well Logging.

Piezoelectric transducers are commonly used in acoustic well logging. However, the low frequency and narrow range of the acoustic waves limit the achievable detection accuracy. In addition, the low amplitude of the waves causes useful information to be easily masked by noise during detection, which affects the accuracy of geological identification and makes it difficult to detect formations tens of meters away. This paper proposes a microporous liquid-electric transmission transducer, in which the microporous electrode structure generates a powerful shock wave through a high-energy instantaneous discharge. First, a model of the liquid-electric microporous transmitting transducer was constructed by combining simulations with numerical calculations, and its electro-acoustic characteristics were analyzed. Then, based on the survey requirements, two innovative optimization schemes for the microporous electrode structure were proposed, namely a triangular pyramid microporous electrode structure and a rectangular microporous electrode structure, and their performances were compared. The results show that the newly optimized triangular pyramid microporous electrode liquid-electric transducer generates acoustic waves with higher amplitude and a wider frequency range than conventional piezoelectric transducers and other microporous structures. It maintains high energy while achieving high frequencies, enabling detection at distances of up to hundreds of meters and the precise characterization of small geological bodies. This has significant implications for applications in marine exploration, land exploration, clean energy, and new energy fields.

A mollifier approach to seismic data representation

AbstractThe extension of the seismic bandwidth to lower frequencies enhances impedance contrasts that can be poorly represented by the broadband acquisition wavelet. Furthermore, long filters that are used to shape the wavelet of processed data can cause issues with noise, phase and interference between seismic events. In this paper, we use a mathematical technique known as mollification to resolve impedance variations with the highest detail allowed by the bandwidth of the data. The mollifier is integrated and windowed to match the low‐frequency content of the data to yield a convenient conversion to relative impedance. Synthetic data created from wedge models show that the windowed mollifier provides an improved representation of the impedance profile. This is replicated by application to an acoustic well log and a regular seismic dataset recorded in the Southern North Sea as well as a broadband dataset recorded in the North Sea.

Using the Conventional Method to Estimate Water Saturation of Khasib Formation in East Baghdad Oil Field Central Area

The water saturation level may change due to geological changes or human intervention, like earthquakes, excavation, injection, or extraction of fluids from underground reservoirs. This work helps the reader understand how to use electrical logging to acquire a suitable water saturation value in resistivity and dielectric studies. In the East Baghdad field, two wells that were drilled into the Khasib Formation had their petrophysical parameters assessed using IP software. This allowed for the determination of water saturation using the available well logs, including neutron, density, SP, sonic, gamma ray, and resistivity logs for wells EB-25, and EB-29. The limestone section in the Khasib formation represents calcite, the main mineral found. We counted the amount of shale in each well using gamma-ray logs. The porosity at the reservoir unit was determined using a sonic log. Archie's equation and resistivity data are also used to compute fluid saturation. Taking m=n=2, a=1, x=1.76, and Rw=0.033 for Khasib formation. The link between Archie's and Raiga's coefficients, a, m, n, and x, is primarily the basis for this discussion. There is high agreement when this equation is used. In clean formations (non-shaly). this formula can be regarded as a reliable indicator of water saturation in situations where porosity techniques other than acoustic logs are unavailable. It's important to note that this equation provides accurate and realistic answers for rocks with transit times between 40 and 150 As/ft. Porosity knowledge is not required for such an assessment.

Using well log data to predict rock compressibility and elasticity in Zubair formation/ southern of Iraq

The mechanical characteristics of rocks such as elasticity (Young's modulus, Poisson's ratio, and unconfined compressive strength) play an essential in sand production analysis, well design, and borehole stability assessment. In this study, the mechanical characteristics of rocks were indirectly estimated using gamma ray, density, and acoustic (compressional and shear) log data from well RU-X in the Rumaila oil field, specifically for the Zubair Formation. These estimated properties were compared to direct measurements obtained from triaxial and uniaxial mechanical tests conducted on well RU-X. The results showed a significant similarity between the indirect estimates and the direct measurements, indicating their reliability for sand production analysis and their valuable contribution to constructing the geomechanical model. Moreover, the static profile of Poisson's ratio was validated using laboratory core test results, demonstrating reasonable agreement. The validation process involved comparing laboratory-derived measurements with actual field measurements in the Zubair Formation. The higher Poisson's ratio observed in the shale was attributed to the slower propagation of acoustic waves, resulting in a good matching with an R2 value of 0.77. On the other hand, the lower Young's modulus in the shaly formations indicated lower resistance to deformation, with a comparative ratio of R²=0.96. Static measurements, which consider various influencing factors, provide a more realistic representation of rock behavior under different conditions. Regarding unconfined compressive strength, the comparative ratio was R²=0.83.

Algorithm for constructing unmeasured logging curves (pseudo-logging) in wells of developed fields

In many cases, the diagrams of some logs in an old well of producing fields are not recorded for some reason or another. Currently, the importance of reassessing the efficiency of such fields is obvious, while the absence of some log curves causes great difficulties. In particular very few studies with acoustic logging (AL) have been carried out in old wells. On the other hand, in 1960-80, among the studies carried out in wells, preference was given to various types of electrical logging (EL), neutron-gamma logging (NGL), and gamma ray logging (GRL). To overcome such difficulties, it is necessary to create diagrams of unmeasured well logs or pseudo-logs. Nowadays, there are methods for constructing pseudolog curves. For example, the method of statistical analysis is widely used. However, in most cases, their implementation is very complex and requires a lot of work. We have developed a new method to construct pseudo-log curves. At first, the propagation velocity of elastic waves in rocks is studied based on seismic survey (SS) and AL data, which are performed presently on the investigation field. Based on this information, objects of interest to the oil industry are selected, their geometric dimensions are determined, the contour of oil and gas saturation is assessed, areas with abnormally high reservoir pressure are studied, the process of accumulation deposition is re-examined, and the preparation of an optimal well network diagram for the effective exploitation of the field is determined. Further, based on the long-ago measured curves of electrical loggings and neutron-gamma logging, we obtain the pseudo-log AL curve in old boreholes and the data SS. The proposed method was tested in 48 wells in the Bahar field (Azerbaijan). The method has shown high efficiency, its reliability is confirmed by independent data. The results of the method help in solving several geological problems: monitoring changes in petrophysical quantities of rocks between wells during development; study of well formations located below the design depth; recalculation of hydrocarbon reserves; determination of the location for drilling new wells, etc

Identification of the low resistivity-low contrast (LRLC) gas-bearing pay zones in Shaly sand reservoirs using acoustic data: a case study from the Messinian Abu Madi formation, onshore Nile Delta, Egypt

AbstractDetection of the low resistivity-low contrast (LRLC) reservoirs is among the main challenges in the oil industry. In this concern, the LRLC pay zones of the Upper Messinian Abu Madi clastic reservoirs in the onshore Nile Delta Gas fields became a main challenge for significant exploration. This type of reservoirs, including low resistivity-low contrast zones and thin-bedded intervals, are often overlooked using the conventional petrophysical evaluation techniques, especially in the wildcat exploratory wells or highly agitated shoreline depositional environments like the Nile Delta of Egypt. These hidden low contrast reservoirs are generally challenging due to the presence of many shale intercalations/laminations and/or due to increasing the shale volume represented in the form of dispersed distribution, and the dominance of conductive clay minerals. Therefore, in this study, the expected high resistivity values of the gas-bearing reservoir intervals of the Abu Madi Formation in the onshore Begonia gas Field, as a typical case study of the LRLC reservoirs, are masked due to the relatively high shale conductivity, particularly when the thickness of these intervals is less than the vertical resolution of the utilized conventional resistivity log. To verify the LRLC phenomena of the Begonia gas Field, the obtained data was compared to the South Abu El Naga gas Field as a normal case study with a relatively high resistivity gas-bearing pay zone. To overcome the impact of the conductive clay mineral content and identify these hidden low resistivity reservoir intervals, it is necessary to integrate the conventional logging data (gamma-ray, shallow and deep resistivity, density, and neutron) with the acoustic log data including shear and compressional sonic data. In this way, a useful relationship can be established enabling the detection of these hidden LRLC reservoir intervals. This integration is based on the principle that shear waves are not influenced by the fluids types, whereas the compressional sonic waves are influenced by the reservoir fluids. However, to effectively investigate these concealed LRLC reservoir intervals, which can boost production and increase the potential reserves, it is essential to have a low water cut value. The present study represents introduces an efficient workflow, which can be extended to other similar LRLC pay zones in the Nile Delta and northeast Africa. It is also extendible to the LRLC reservoirs in similar deltaic systems having conductive minerals-bearing reservoirs or thin beds.

Discharge Experiment and Structure Optimisation Simulation of Impulse Sound Source

The wave frequency and energy of traditional piezoelectric emission sources used in acoustic logging are limited, which results in an inadequate detection resolution for measuring small-scale geological formations. Additionally, the propagation of these waves in formations is prone to loss and noise interference, restricting detection to only a few tens of meters around the well. This paper investigates an impulse sound source, a new emission source that can effectively enhance the frequency range and wave energy of traditional sources by generating excitation waves through high-voltage discharges in a fluid-penetrated electrode structure. Firstly, a high-voltage circuit experimental system for the impulse sound source was constructed, and the discharge and response characteristics were experimentally analyzed. Then, four types of needle series electrode structure models were developed to investigate and compare the effects of different electrode structures on the impulse sound source, with the needle-ring electrode demonstrating superior performance. Finally, the needle-ring electrode structure was optimized to develop a ball-tipped needle-ring electrode, which is more suitable for acoustic logging. The results show that the electrode structure directly influences the discharge characteristics of the impulse sound source. After comparison and optimization, the final ball-tipped needle-ring electrode exhibited a broader frequency range—from zero to several hundred thousand Hz—while maintaining a high acoustic amplitude. It has the capability to detect geological areas beyond 100 m and is effective for evaluating micro-fractures and small fracture blocks near wells that require high detection accuracy. This is of significant importance in oil, gas, new energy, and other drilling fields.

Evaluation of Fracturing Effect of Tight Reservoirs Based on Deep Learning.

The utilization of hydraulic fracturing technology is indispensable for unlocking the potential of tight oil and gas reservoirs. Understanding and accurately evaluating the impact of fracturing is pivotal in maximizing oil and gas production and optimizing wellbore performance. Currently, evaluation methods based on acoustic logging, such as orthogonal dipole anisotropy and radial tomography imaging, are widely used. However, when the fractures generated by hydraulic fracturing form a network-like pattern, orthogonal dipole anisotropy fails to accurately assess the fracturing effects. Radial tomography imaging can address this issue, but it is challenged by high manpower and time costs. This study aims to develop a more efficient and accurate method for evaluating fracturing effects in tight reservoirs using deep learning techniques. Specifically, the method utilizes dipole array acoustic logging curves recorded before and after fracturing. Manual labeling was conducted by integrating logging data interpretation results. An improved WGAN-GP was employed to generate adversarial samples for data augmentation, and fracturing effect evaluation was implemented using SE-ResNet, ResNet, and DenseNet. The experimental results demonstrated that ResNet with residual connections is more suitable for the dataset in this study, achieving higher accuracy in fracturing effect evaluation. The inclusion of the SE module further enhanced model accuracy by adaptively adjusting the weights of feature map channels, with the highest accuracy reaching 99.75%.

Borehole radiation wavefield for multipole logging while drilling with an eccentric collar

Abstract This study investigates the radiation characteristics of the borehole-source in acoustic logging while drilling (ALWD) with an eccentric collar. Understanding these characteristics is crucial for the development of acoustic remote detection technology, which has shown great potential in ALWD. Considering the frequent occurrence of tool eccentricity during drilling, it is essential to take into account its impact on the acoustic wavefield outside the borehole. In this paper, we establish an ALWD model with an eccentric collar in a dual-cylindrical coordinate system. By applying the translational Bessel addition theorem and the steepest descent method, we obtain the far-field asymptotic solution of the problem and model the radiation wavefield. Our findings indicate that the asymmetrical radiation pattern resulting from drill collar eccentricity can effectively resolve ambiguities in determining the reflector azimuth.

Dipole acoustic remote detection (ARD) logging and its application in fracture-cave reservoir

Abstract Oil and gas from deep reservoirs are mostly enriched in the fracture-cave reservoirs. For this reason, fine evaluation of large-scale fracture-cave and effective detection of small scale fracture-cave are the key issues to be solved in the exploration of fracture-cave type carbonate reservoirs. The acoustic remote detection logging technology is based on acoustic reflection method to continuously image the formation around the well. The cross dipole array sonic data can be processed to image geological anomalies within a range of about 20 meters outside the well. Dipole S wave remote detection has the remarkable advantages of low emission frequency and larger investigation depth, but it has 180 degrees’ azimuthal ambiguity. This study is based on previously developed far field dipole S wave remote detection tool, finite difference is performed on formation models with and without are obtained for representative fracture-cave formations and remote detection processing and interpretation software is updated. These are applied on a well in the northwestern area. Through the comprehensive analysis of remote logging, conventional logging, electrical imaging logging and seismic data of the fracture-cave geological anomalies, a fine picture of the morphology and development of the geological anomalies from the near wellbore to the far end is formed

Delineating aquitard characteristics within a Silurian dolostone aquifer using high-density hydraulic head and fracture datasets

Fractured aquifers are heterogeneous due to the variable frequency, orientation, and intersections of rock discontinuities. A ~100-m-thick Silurian dolostone sequence provides a bedrock aquifer supplying the city of Guelph, Canada. Here, fracture network characteristics and associated influences on hydraulic head were examined using several data types obtained from 24 cored holes in a study that is novel for the quantity and quality of data. High (50–90°) angle joint orientations, heights, and terminations relative to bedding features were determined from acoustic televiewer logs and outcrop scanlines. These data were compared to high-resolution hydraulic head profiles showing head loss over depth-discrete intervals identifying zones with lower vertical hydraulic conductivity. This study reveals that the marl-rich Vinemount Member, traditionally considered the principal aquitard, corresponds to head loss in only 62% of the 24 boreholes. The vertical position of head loss varies across the 90-km2 study area and occurs in any of the lithostratigraphic units of the Lockport Group. Within this sedimentary sequence, aquitards are laterally discontinuous or “patchy” at variable depths and relate to: (1) the frequency of the high-angle joints; (2) shorter joint height; and (3) the type of joint terminations. The head loss occurs in thin (2–2.5 m) intervals where the frequency of the high-angle joints is low. Where a large proportion of small joints cross-cut marl bedding planes, head loss is negligible, suggesting that the vertical hydraulic conductivity is not reduced. Overall, these findings are potentially applicable to assessing aquitard and cap rock integrity in carbonate sedimentary sequences worldwide.

Research on Iron Gallium Dipole Logging Transducers

Abstract Orthogonal dipole acoustic logging is an indispensable means to study the mechanical properties of formation rocks, estimate formation porosity and permeability, and carry out out-of-hole remote detection, and the broadband high-power dipole acoustic logging transducer is one of its core components, which is an urgent and unsolved international problem in actual logging. Therefore, it is of great application background and important academic significance to study the new dipole acoustic logging transducer and overcome the related scientific problems. On the basis of full investigation and study of the characteristics of iron gallium materials, this project first designed the iron gallium bending beam oscillator to verify the feasibility of iron gallium bending vibration, and then designed the iron gallium dipole acoustic logging transducer, optimized the driving magnetic circuit, simulated the driving performance of the transducer, and preliminarily verified the feasibility of the design.

Shear wave measurement in slow formations for eccentric monopole acoustic logging while drilling

Abstract The use of a logging-while-drilling (LWD) monopole tool to directly measure shear (S) wave velocity in slow formations has been proven feasible under certain conditions. However, S-wave signals received in the borehole are fairly weak, which limits the application range of this measurement method. To find ways to enhance shear waves, we first explore factors sensitive to the S-wave excitation. Simulation results indicate that four parameters including the receiver-source distance, the radial distance from receiver to borehole wall, the formation S-wave velocity and source frequency, primarily influence the S-wave excitation. Shear waves can be enhanced by judiciously optimizing these parameters during tool design. We also investigate borehole wavefields with an eccentric LWD tool in both commonly slow and ultra-slow formations. Results reveal that tool eccentricity can amplify shear waves and improve its measurement accuracy, provided that waveforms received in the direction of tool movement are used. We successfully extracted the S-wave velocity of an ultra-slow formation under conditions of large eccentricity, while similar actions originally failed with a centralized instrument.

Investigation on the fatigue properties of adhesives for acoustic transducers in deep logging wells

Abstract Deep well exploration of oil and gas resources requires acoustic transducers that can withstand temperatures above 200 degrees. It is particularly important to overcome the key technology of high-temperature dipole transmitters. The bonding strength of the dipole transmitters with a tri-laminar structure is studied numerically and experimentally. Transducers were prepared using structural adhesives. The aging and fatigue test is conducted at a high temperature of 200 degrees. The aging lasted for 15 hours and the strong electric field fatigue cycle number reached up to 36000. The conductivity curve remains almost unchanged after the high-temperature test. The work provides an application basis for deep acoustic logging technology.

Present-day stress stratification in the lower Palaeozoic shale sequence of the Baltic Basin, northern Poland, inferred from borehole data

We performed an analysis of present-day stress profiles for four wells penetrating the Lower Palaeozoic shale sequence of the Baltic Basin (northern Poland). Breakouts, hydraulic fracturing and leak-off tests were used to calibrate stress models based on anisotropic elastic shale properties. Initial stress models, balancing the lengths of the modelled and observed breakouts, indicated a degradation of the mechanical properties reconstructed from the density and dipole acoustic tool logs. Taking this adverse effect into account, final stress models were calculated which showed a stratification of the stress regime consistent with the lithostratigraphic shale units. A clear dominance of the horizontal stress-generating gravity factor over the horizontal tectonic strain was demonstrated. The obtained values of tectonic strain in the shale sequence compared to the previously determined strain in the crystalline basement of the same study area suggest a significant role of viscoelastic relaxation of the shale sequence.

Inversion of gas hydrate saturation and solid frame permeability in a gas hydrate-bearing sediment by Stoneley wave attenuation

Natural gas hydrate is a potential novel energy resource that is widely distributed globally. Acoustic logging can effectively provide information on the surrounding reservoir and plays an important guiding role in gas hydrate exploration and development. Natural gas hydrate-bearing sediments are composed of a solid frame with natural gas hydrates and water-filled pores. The borehole mode wave characteristics of two-phase porous media cannot be used to evaluate the parameters of such a multiphase porous medium. We explore factors that influence the monopole Stoneley wave in a borehole embedded in a multiphase porous medium containing two solids and one fluid and analyze the influence of each factor on monopole Stoneley wave attenuation systematically. The sensitivity analysis results indicate that the Stoneley wave attenuation is highly sensitive to solid frame permeability and gas hydrate saturation. Building upon this foundation, a method to invert for gas hydrate saturation and solid frame permeability is first developed using Stoneley wave attenuation. Synthetic logging data are used to demonstrate the feasibility of this method for inverting for gas hydrate-bearing sediment properties. Even in the presence of considerable noise added to the receiver signal arrays, the inversion method is stable, and reliably evaluates gas hydrate saturation and solid frame permeability.