Acid Etching Treatment Research Articles

Effect of acid-etching 3D printed Ti templates on mechanical properties and corrosion resistance of Mg alloy scaffolds with different pore geometries

Segmental bone defect repair currently remains a major challenge in orthopedic clinics. In this study, to match different implantation positions, different pore geometries (P, G and Do) of Mg alloy scaffolds were designed and prepared by infiltration casting with the acid-etching treated Ti scaffold as the templates. The results showed that the acid-etching treatment for Ti templates resulted in a smoother surface of the Mg alloy scaffolds with improving the mechanical properties and corrosion resistance. Both experiments and simulations showed that the P scaffold had the highest mechanical properties, with yield strength and elastic modulus up to 26.7±2.1 MPa and 327.1±16.2 MPa, respectively. And the P scaffold had the best corrosion resistance after cleaning the Ti template, with a degradation rate of 0.34±0.17 mm/y at 228 h. In vitro cellular experiments showed good cytocompatibility on the surface of all three scaffolds.

Gas-Solid Reaction Synthesis and Electrocatalytic Oxygen Reduction of Pt-Skin L10-PtFe/C.

Compared to Pt/C, the atomic ordered Pt-based intermetallic compounds can deliver higher efficiency and reliable stability, and they are considered one of the ideal cathode catalysts for the next generation of fuel cells. This work proposed a simple ferrocene atmosphere annealing method to improve commercial Pt/C and convert Pt to L10-PtFe. After further acid etching treatment, the obtained carbon-supported Pt-skin L10-PtFe (Pt-skin L10-PtFe/C) with superfine particle size (∼3.3 nm) not only was highly dispersed on the carbon but possesses a thin Pt skin, like the armor of L10-PtFe. As excepted, the ORR activity of Pt-skin L10-PtFe/C (0.375 A mg-1; 0.921 mA cm-2) is far better than that of commercial Pt/C (0.121 A mg-1; 0.260 mA cm-2), and its stability is also greatly improved. Our proposed gas-solid reaction is straightforward and has great potential in producing Pt-based intermetallic catalysts on a large scale.

Comparison of Zirconia Implant Surface Modifications for Optimal Osseointegration.

Zirconia ceramic implants are commercially available from a rapidly growing number of manufacturers. Macroscopic and microscopic surface design and characteristics are considered to be key determining factors in the success of the osseointegration process. It is, therefore, crucial to assess which surface modification promotes the most favorable biological response. The purpose of this study was to conduct a comparison of modern surface modifications that are featured in the most common commercially available zirconia ceramic implant systems. A review of the currently available literature on zirconia implant surface topography and the associated bio-physical factors was conducted, with a focus on the osseointegration of zirconia surfaces. After a review of the selected articles for this study, commercially available zirconia implant surfaces were all modified using subtractive protocols. Commercially available ceramic implant surfaces were modified or enhanced using sandblasting, acid etching, laser etching, or combinations of the aforementioned. From our literature review, laser-modified surfaces emerged as the ones with the highest surface roughness and bone-implant contact (BIC). It was also found that surface roughness could be controlled to achieve optimal roughness by modifying the laser output power during manufacturing. Furthermore, laser surface modification induced a very low amount of preload microcracks in the zirconia. Osteopontin (OPN), an early-late osteogenic differentiation marker, was significantly upregulated in laser-treated surfaces. Moreover, surface wettability was highest in laser-treated surfaces, indicating favorable hydrophilicity and thus promoting early bone forming, cell adhesion, and subsequent maturation. Sandblasting followed by laser modification and sandblasting followed by acid etching and post-milling heat treatment (SE-H) surfaces featured comparable results, with favorable biological responses around zirconia implants.

Acid treatment enhances the methane combustion activity of LaFeO3 perovskite catalyst

The catalytic combustion of methane has gained much attention as a sustainable technology, due to concerns about the environmental impact of unburnt methane emissions from the natural gas vehicles. Researchers have explored alternatives to precious metal catalysts for methane combustion, with a focus on perovskite oxides known for their excellent activity and sintering-resistance capacity. In this study, LaFeO3 perovskite material was synthesized and subsequently subjected to a nitric acid etching treatment to modify its surface. It was found that the acid preferentially dissolved La cations from LaFeO3 surface while the perovskite phase was unchanged, as a consequence, the etched LaFeO3 shows improvement in methane combustion activity. The best performance was achieved in the sample with one-hour surface etched treatment, which suggests that the appropriate surface reconstruction induced by acid treatment promotes the formation of more active Fe sites on the surface and reduces the energic barriers of methane activation. This work presents a straightforward and effective approach to tailor the exposed surface properties of perovskites, thereby enhancing their activity in hydrocarbon combustion reactions.

Comparative clinical evaluation of the stability of implants using double acid etching treatment with and without the addition of fluoride solution: A randomized clinical trial.

Osseointegration depends on primary stability, and further, implant surface modifications may improve secondary stability. This randomized clinical trial evaluates whether adding a fluoride solution enhances the implant stability. Stability of dental implants with two different types of surface treatments was compared utilizing resonance frequency analysis (RFA). Twelve patients were recruited: eight females and four males with an average age of 58.3 years and they received either double acid etched implants (control: Porus Implant, Sistema Conexão) and double acid etched implants containing fluoride on their surfaces (test: Porus Nano Implant, Sistema Conexão). Each patient received one implant from the test category and another implant from the control category, resulting in 24 implants in this study. RFA, utilizing Osstell was used to assess the implant stability, immediately after the placement of implant and 15, 30 and 45 days post-implant placement. At the initial time, there was no difference between the test and control groups regarding the ISQ. However, after 15, 30, and 45 days, ISQ values for the test group were significantly higher than the control group. When using implants without fluoride addition, it was observed that after 15 days, the ISQ values were lower than those found at the initial time, but after 30 days, values matched the initial. Concerning the test group results, the ISQ values from T0 (immediately after implant placement) to T3 (45 days after implant placement) always increased from every period of evaluation. It was concluded that double acid etched implants with surfaces containing fluoride solution increases the implant stability quotient, compared to implants with fluoride-free double acid etched surfaces.

Surface modification strategies of 304 austenitic stainless steel plate with different micromorphology and composition for improved mechanical interlocking and chemical bonding in metal–epoxy joints

304 austenitic stainless-steel (SS) strip-based carbon fiber metal laminates (CFMLs) have raised significant concerns, in terms of their mechanical performance. On top of that, the hybrid laminates’ interlamination performance is vital in regulating their failure patterns. Along these lines, in this work, SS strips with regulatable micromorphology and composition were obtained by using physical and chemical surface modification strategies, including polishing, acid etching, anodization, and thermal treatment. The shear strength of the treated-SS/epoxy single lap joints (two treated-SS strips bonded by the epoxy resin via hot curing process) was systematically explored, and the origins of the enhancement mechanism were attributed to the resulting surface microstructure, as well as the possible chemical reactions between the treated surface and the curing agent. The etching-anodizing-thermally treated-SS (EAT-SS)/epoxy joint exhibited the maximum shear strength (16.04 MPa) and work of fracture (5.85 kJ·m−2) due to the substantial cohesive failure pattern of the epoxy. The encouraging enhancement was mainly attributed to the synergistic effect of the micro-annular pit and the nanoporous array structure of the EAT-SS surface. These effects induced a significant mechanical interlock and a plausible chemical reaction at the interface, which led to improved bonding strength between the epoxy and treated-SS surface. Overall, in this work, it was demonstrated that the combination of the anodization and thermal treatment can effectively improve the interlamination bonding properties between the SS strip and the epoxy resin due to the combination effect of mechanical interlocking and chemical bonding.

Surface Treatment of Indirect Restorations

Background: All ceramic CAD/CAM materials require surface treatment protocols varying from one type to another according to their chemical composition, including hydrofluoric acid etching, sandblasting, silica coating, laser etching, and non-thermal plasma treatment. This review's objective to analyze and bring up-to-date data about the surface treatment of ceramics.Data: The review just searched electronic publications of papers. Websites "Google Scholar" and "PubMed" were utilized as sources for performing data searches using the following keywords: Surface modification, plasma surface treatment, indirect restoration, ceramics The original papers and clinical investigations that were published between the years 2006 to March 2023 that were the most relevant to the subject at hand were chosen.Conclusion: A variety of surface treatment methods have been proposed to enhance the bonding of restorative materials to resin cement and provide micromechanical retention by altering the restoration's surface mechanically by increasing the degree of roughness or physico/chemically by activating the surface. Hydrophloric acid etch is a golden standard for the surface treatment of feldspathic and lithium disilicate ceramics, the APC concept for zirconia, and hydrofluoric acid or sandblast surface treatment for resin nano-ceramic. A new approach used for surface treatment is plasma treatment, which is really promising in dentistry.

Facile fabrication of an enhanced electrodeposited nickel electrode for alkaline hydrogen evolution reaction

Electrodeposited nickel (Ni) electrode for alkaline hydrogen evolution reaction (HER) has low cost and high stability advantages, but its catalytic performance is unsatisfactory. In this study, a Ni electrode with a pentagonal pyramid microstructure was first fabricated by electrodeposition, and then the surface microstructure and chemical composition of the electrode were elaborately modified by a simple acid etching treatment which significantly enhanced the HER catalytic performance. The HER over-potential at 10 mA cm−2 on the electrode which was etched for 60 min was reduced from 238 mV to 60 mV compared to the un-etched one. The fabricated electrode could maintain stable catalytic stability at a current density of 100 mA cm−2 beyond 360 h. The surface microstructures and chemical compositions of the electrodes were characterized and the catalytic kinetics were investigated by electrochemical methods. The steps on the pentagonal pyramids on the Ni electrode were preferentially dissolved in the etching treatment and the surface became undulating, which efficiently increased the electrochemically active surface area (ECSA). The etching treatment improved the surface wettability and accelerated the hydrogen bubble detachment speed on the electrode. Meanwhile, the electrode surface was further oxidized in the etching treatment. Metallic Ni and crystal NiO were alternately presented on the electrode surface. The generated NiO could facilitate the Volmer step in the HER, which led to the change of the rate-controlling step from the Volmer step to the Heyrovsky step. Further, the synergistic effect between Ni and NiO with a suitable ratio improved the HER catalytic performance of the electrode.

Influence of surface topographic morphologies and nanoparticle incorporation on surface properties of pure Ti implants for oral applications

One common problem in using titanium (Ti) dental implants is peri-implantitis. To prevent peri-implantitis on Ti implants in an oral environment, we introduced novel topographic microstructures onto the surfaces of pure Ti implants via sandblasting, acid etching, and hydrothermal treatment before adding ZnO nanocomposite coatings and TiO2 nanocomposite coatings via magnetron sputtering. We comprehensively investigated the influence of surface topographic morphologies and elemental composition of coatings on the physicochemical properties and antibacterial efficacy of the specimens. Our results indicate that the novel topographic surfaces and magnetron sputtered coatings both exhibit good cytocompatibility. Our results also suggest that coating composition, rather than surface topographic morphology, is the primary factor influencing the antibacterial performance of Ti implants. Therefore, the magnetron sputtering of ZnO and TiO2 coatings onto surfaces can be an effective technique for improving the antibacterial properties of Ti implants for oral applications.

Effect of Phytic Acid Etching and Airborne-Particle Abrasion Treatment on the Resin Bond Strength.

This study aimed to evaluate the bond strength of a universal adhesive to dentin (μTBS) using different time periods of airborne particle abrasion (APA) and two types of acid etching. Seventy-two human third molars were divided into 9 groups (n=8) according to dentin pretreatment: APA duration (0, 5, or 10s) and acid etching (no acid - NA, 37% phosphoric acid - PhoA, or 1% phytic acid - PhyA). APA was performed at a 0.5 cm distance and air pressure of 60 psi using 50 μm aluminum oxide particles. Afterwards, two coats of Single Bond Universal adhesive (3M) were applied to the dentin surface. Composite blocks were built using the incremental technique, sectioned into 1×1 mm slices and subjected to microtensile bond strength (μTBS) testing. Fracture patterns and surface topography of each dentinal pretreatment were evaluated using a Scanning electron microscope (SEM). Bond strength data were analyzed using two-way ANOVA and Bonferroni post-hoc tests. The group that received pretreatment with 5s APA and PhoA presented higher μTBS values among all groups, which was statistically different when compared with the PhoA, 10APA+PhoA, and 5APA+PhyA groups. PhyA did not significantly influence the bond strength of the air-abraded groups. Finally, adhesive failure was considered the predominant failure in all groups. Dentin pretreated by airborne particle abrasion using aluminum oxide demonstrated an increase in bond strength when abraded for 5 seconds and conditioned with phosphoric acid in a universal adhesive system.

Characteristic fatigue strength and reliability of dental glass-ceramics: Effect of distinct surface treatments – Hydrofluoric acid etching and silane treatment vs one-step self-etching ceramic primer

The aim of this study was to mechanically characterize through flexural fatigue test two CAD-CAM glass-ceramics according to distinct surface etching protocols. To do so, feldspathic (FELD) and lithium disilicate (LD) glass ceramics were subjected to different surface treatments: (1) control – no treatment (Ctrl); (2) conventional protocol etching with 5% hydrofluoric acid followed by silane coupling agent application (HF + SIL; Monobond N, Ivoclar); or (3) using a self-etching ceramic primer (E&P; Monobond Etch & Prime, Ivoclar). Ceramic discs (N = 120; Ø = 12 mm; thickness = 1.2 mm) were produced from CAD-CAM blocks, with 60 being from FELD (VITABLOCS Mark II, Vita Zahnfabrik) and 60 from LD (IPS e.max CAD, Ivoclar). Next, 20 disks of each ceramic were allocated into three groups: Ctrl, HF + SIL, or E&P. Surface roughness data were collected on all samples before and after surface treatments (except for Ctrl). Cyclic fatigue (n = 15) biaxial flexural strength tests were performed by the piston-on-three-balls geometry (ISO 6872) considering the test parameters established from a monotonic test (n = 5). The monotonic test was carried out at a 1 mm/min loading rate and 500 kgf loading cell until fracture to obtain the failure data. The cyclic fatigue test was executed underwater at a frequency up to 20 Hz, with the first stress being 25% of the monotonic test for 5000 cycles, followed by increments of 5% of the monotonic test at each step of 10,000 cycles until failure (fracture). Complementary fractography, topography and Atomic Force Microscopy (AFM) analyses were performed. Characteristic Fatigue Strength (CFS) and Weibull modulus were analyzed by Weibull analysis using the fatigue test data. Roughness and complementary analysis data were analyzed by one-way ANOVA. The statistical results exhibited similar CFS among Ctrl, HF + SIL and E&P for both glass-ceramics. The survival analysis corroborates the findings, however the Weibull modulus pointed out superior structural reliability of FELD treated with the E&P group compared to HF + SIL. According to the complementary analyses, HF + SIL exhibited a higher surface area than E&P and Ctrl for FELD (p = 0.001). Roughness showed statistically significant differences among conditions for FELD (E&P < Ctrl = HF + SIL; p < 0.05) and no difference for LD (p > 0.05). Therefore, the CFS were not influenced by any condition evaluated for FELD and LD glass-ceramics; however, superior structural reliability (higher Weibull modulus) for the feldspathic ceramic treated with the E&P was observed.

Experimental investigation on mode I fracture characteristics of Longmaxi formation shale after cyclic thermal shock and high-temperature acid etching treatments

Fracture toughness is a key parameter for shale hydraulic fracturing design, which directly affects the fracture initiation pressure. In this paper, the influence of cyclic thermal shock and high-temperature acid etching on the Mode I fracture of Longmaxi Formation shale was investigated. The crack propagation was obtained by using acoustic emission (AE) and digital image correlation (DIC) techniques. Meanwhile, the fracture surface morphology and microstructure of the specimens were analyzed using white light interferometer and scanning electron microscope (SEM). The experimental results demonstrate that cyclic thermal shock severely degrades the nominal strength and fracture toughness of shale. The average fracture toughness is found to be only 0.67 MPa·m0.5, which accounts for a reduction of 25.9 %. AE analysis reveals that microfracture is the dominant mechanism, with the highest amplitude of AE source only 78 dB. The critical strain value of the fracture propagation zone (FPZ) is determined to be 1.35 ‰, and SEM images indicate that along-crystal fracture is the primary fracture mechanism. On the other hand, the shale specimen subjected to high-temperature acid-etching treatment exhibits an average fracture toughness of 0.86 MPa·m0.5, with the AE source amplitude reaching 86 dB. The critical strain value of the FPZ was measured to be 2.38 ‰. The fracture surface appears smooth and is mainly characterized by perforated-crystal rupture. The findings of this study not only enhance our understanding of shale mode I fracture toughness but also provide valuable insights for optimizing process parameters to reduce initiation pressure in deep shale formations.

Bimetallic zeolitic imidazole framework-derived sulfur-doped porous carbon as highly efficient catalysts for oxygen reduction reaction in proton exchange membrane fuel cells

The oxygen reduction reaction (ORR) is the most sluggish half-reaction in fuel cells; therefore, Pt-group metal (PGM)-based electrocatalysts have been employed to circumvent this limitation. However, the use of Pt, which is a precious metal, significantly limits the commercialization of proton-exchange membrane fuel cell (PEMFC) systems because of the high cost and low durability of Pt-based materials. Herein, we introduce advanced S-doped Co–N–C (CoNC) porous electrocatalysts (S-CoNPCs) derived from zeolitic imidazole frameworks as substitutes for PGM-based electrocatalysts. To improve the electrocatalytic activity of CoNC, sulfur doping, and acid etching treatment methods, which are innovative procedures, are employed to obtain high catalytic activity and a large surface area. S-CoNPC demonstrates an extremely improved electrochemical performance for ORR in both alkaline and acidic mediums compared with commercial Pt/C, exhibiting Eonset, E1/2, and limiting current density of approximately 0.91 V, 0.85 V, and −6.7 mA cm−2 (at 0.40 V vs. RHE), respectively, which are in the suitable range for commercializing the PEMFCs system. Furthermore, S-CoNPC, which exhibits high selectivity, stability, and methanol tolerance, is a promising, novel, and advanced non-PGM electrocatalyst for diverse applications.

Effect of Dentin and Zirconia Surface Treatments with Laser Irradiation Versus Sandblasting on the Bonding Ability of Zirconia.

Objective: This study aimed to investigate the effects of laser irradiation applied to zirconia and tooth surfaces on shear bond strength (SBS) compared with acid etching and sandblasting. Background: The effect of laser irradiation on the bond strength between zirconia and adhesives is a controversial issue for dentin surface treatments. In addition, the effects of different combinations of surface treatments to increase adhesion on both the zirconia and dentin surfaces remain unclear. Materials and methods: A total of 90 tooth samples were assigned into groups according to various pretreatments: control group was left untreated, acid etching, and Erbium, Chromium:Yttrium Scandium Gallium Garnet (Er,Cr:YSGG) laser irradiation group (15 Hz, 2 W). In addition, the zirconia specimens were separated into three groups (n = 10) according to the different surface treatments performed: sandblasting (120 μm Al2O3), Er,Cr:YSGG laser (15 Hz, 2 W), and as untreated surface. The zirconia samples were cemented to the dentin surface using dual-cure resin cement and subjected to an SBS test at a speed of 0.5 mm/min under a universal testing machine until fractures occurred in the bonding surface. Results: The highest SBS values were observed in Group tooth acid (TA)-zirconia Er,Cr:YSGG laser (ZL), followed by Group tooth Er,Cr:YSGG laser (TL)-zirconia sandblasting (ZS) and Group TA-zirconia control (ZC). The lowest SBS values were found in Group TA-ZS. Significant intergroup difference was noted between Group TA-ZL, Group tooth control (TC)-ZC, Group TL-ZS, and Group TC-ZC. However, no significant difference was noted between Group TA-ZL, Group TL-ZS, and Group TA-ZC. Conclusions: Acid etching and laser treatments applied to the dentin and zirconia surfaces were found to be effective techniques for improving the zirconia-dentin bond, respectively. Clinical Trial Registration number: 33216249-604.01.02-E.24308.

The Action of Angiocrine Molecules Sourced from Mechanotransduction-Related Endothelial Cell Partially Explain the Successful of Titanium in Osseointegration.

Since Branemark's findings, titanium-based alloys have been widely used in implantology. However, their success in dental implants is not known when considering the heterogenicity of housing cells surrounding the peri-implant microenvironment. Additionally, they are expected to recapitulate the physiological coupling between endothelial cells and osteoblasts during appositional bone growth during osseointegration. To investigate whether this crosstalk was happening in this context, we considered the mechanotransduction-related endothelial cell signaling underlying laminar shear stress (up to 3 days), and this angiocrine factor-enriched medium was harvested further to use exposing pre-osteoblasts (pOb) for up to 7 days in vitro. Two titanium surfaces were considered, as follows: double acid etching treatment (w_DAE) and machined surfaces (wo_DAE). These surfaces were used to conditionate the cell culture medium as recommended by ISO10993-5:2016, and this titanium-enriched medium was later used to expose ECs. First, our data showed that there is a difference between the surfaces in releasing Ti molecules to the medium, providing very dynamic surfaces, where the w_DAE was around 25% higher (4 ng/mL) in comparison to the wo_DAE (3 ng/mL). Importantly, the ECs took up some of this titanium content for up to 3 days in culture. However, when this conditioned medium was used to expose pOb for up to 7 days, considering the angiocrine factors released from ECs, the concentration of Ti was lesser than previously reported, reaching around 1 ng/mL and 2 ng/mL, respectively. Thereafter, pOb exposed to this angiocrine factor-enriched medium presented a significant difference when considering the mechanosignaling subjected to the ECs. Shear-stressed ECs showed adequate crosstalk with osteoblasts, stimulating the higher expression of the Runx2 gene and driving higher expressions of Alkaline phosphatase (ALP), bone sialoprotein (BSP), and osteocalcin. Mechanotransduction-related endothelial cell signaling as a source of angiocrine molecules also stimulated the higher expression of the Col3A1 gene in osteoblasts, which suggests it is a relevant protagonist during trabecular bone growth. In fact, we investigated ECM remodeling by first evaluating the expression of genes related to it, and our data showed a higher expression of matrix metalloproteinase (MMP) 2 and MMP9 in response to mechanosignaling-based angiocrine molecules, independent of considering w_DAE or the wo_DAE, and this profile reflected on the MMP2 and MMP9 activities evaluated via gelatin-based zymography. Complimentarily, the ECM remodeling seemed to be a very regulated mechanism in mature osteoblasts during the mineralization process once both TIMP metallopeptidase inhibitor 1 and 2 (TIMP1 and TIMP2, respectively) genes were significantly higher in response to mechanotransduction-related endothelial cell signaling as a source of angiocrine molecules. Altogether, our data show the relevance of mechanosignaling in favoring ECs' release of bioactive factors peri-implant, which is responsible for creating an osteogenic microenvironment able to drive osteoblast differentiation and modulate ECM remodeling. Taking this into account, it seems that mechanotransduction-based angiocrine molecules explain the successful use of titanium during osseointegration.

Atomic Layer Deposition of Tantalum Oxide Films on 3D-Printed Ti6Al4V Scaffolds with Enhanced Osteogenic Property for Orthopedic Implants.

There is an evident advantage in personalized customization of orthopedic implants by 3D-printed titanium (Ti) and its alloys. However, 3D-printed Ti alloys have a rough surface structure caused by adhesion powders and a relatively bioinert surface. Therefore, surface modification techniques are needed to improve the biocompatibility of 3D-printed Ti alloy implants. In the present study, porous Ti6Al4V scaffolds were manufactured by a selective laser melting 3D printer, followed by sandblasting and acid-etching treatment and atomic layer deposition (ALD) of tantalum oxide films. SEM morphology and surface roughness tests confirmed that the unmelted powders adhered on the scaffolds were removed by sandblasting and acid-etching. Accordingly, the porosity of the scaffold increased by about 7%. Benefiting from the self-limitation and three-dimensional conformance of ALD, uniform tantalum oxide films were formed on the inner and outer surfaces of the scaffolds. Zeta potential decreased by 19.5 mV after depositing tantalum oxide films. The in vitro results showed that the adhesion, proliferation, and osteogenic differentiation of rat bone marrow mesenchymal stem cells on modified Ti6Al4V scaffolds were significantly enhanced, which may be ascribed to surface structure optimization and the compatibility of tantalum oxide. This study provides a strategy to improve the cytocompatibility and osteogenic differentiation of porous Ti6Al4V scaffolds for orthopedic implants.

Catalytic Oxidation of Acetone on SmMn2O5: Effect of Acid Etching and Loading Treatment.

The key of catalytic oxidation technology is to develop a stable catalyst with high activity. It is still a serious challenge to achieve high conversion efficiency of acetone with an integral catalyst at low temperature. In this study, the SmMn2O5 catalyst after acid etching was used as the support, and the manganese mullite composite catalyst was prepared by loading Ag and CeO2 nanoparticles on its surface. By means of SEM, TEM, XRD, N2-BET, XPS, EPR, H2-TPR, O2-TPD, NH3-TPD, DRIFT, and other characterization methods, the related factors and mechanism analysis of acetone degradation activity of the composite catalyst were discussed. Among them, the CeO2-SmMn2O5-H catalyst has the best catalytic activity at 123 and 185 °C for T50 and T100, respectively, and shows excellent water and thermal resistance and stability. In essence, the surface and lattice defects of highly exposed Mn sites were formed by acid etching, and the dispersibility of Ag and CeO2 nanoparticles was optimized. Highly dispersed Ag and CeO2 nanoparticles have a highly synergistic effect with the support SmMn2O5, and the reactive oxygen species provided by CeO2 and the electron transfer brought by Ag further promote the decomposition of acetone on the carrier SMO-H. In the field of catalytic degradation of acetone, a new catalyst modification method of high-quality active noble metals and transition metal oxides supported by acid-etched SmMn2O5 has been developed.

Preparation, aging behavior and interface bonding of cordierite glass-ceramics as veneer porcelain for Si3N4 ceramics

In this work, aiming at developing veneer porcelain for Si3N4 dental ceramics, the cordierite glass-ceramics were prepared via the sintering method and the effects of glass powder particle size and accelerated aging time on the structure and properties of cordierite glass-ceramics were investigated. With the milling time extension, the glass powder particle size decreases and becomes more uniform, the sintering property, bending strength and fracture toughness increase and then decrease. The cordierite glass-ceramics prepared from glass powder with ball milling time of 10 h exhibit the optimum performance which meets the standard requirements for dental ceramics. Accelerated aging test was conducted in distilled water at 134 °C and 2 atm. After accelerated aging for 10 h, the performance of the samples still can meet the standard requirements, suggesting good stability and anti-aging properties. Effects of HF acid etching and oxidation treatment of Si3N4 ceramics on the microstructure, bonding strength and failure mechanism of the cordierite glass-ceramics/Si3N4 ceramics interface were assessed. HF acid etching can effectively improve the surface roughness of Si3N4 ceramics, and the interface exhibits a mixed failure mode with a bonding strength of 8.49 MPa.

Boosting the Sonodynamic Cancer Therapy Performance of 2D Layered Double Hydroxide Nanosheet-Based Sonosensitizers Via Crystalline-to-Amorphous Phase Transformation.

Sonodynamic therapy (SDT) has been a promising therapeutic modality for cancer because of its superior advantages compared with other therapeutic strategies. However, the current sonosensitizers used for SDT normally exhibit low activity for ultrasound (US)-induced reactive oxygen species (ROS) generation. Herein, the crystalline-to-amorphous phase transformation is reported as a simple but powerful strategy to engineer ultrathin 2D CoW-LDH and NiW-LDH nanosheets as highly efficient sonosensitizers for SDT. The phase transformation of CoW-LDH and NiW-LDH nanosheets from polycrystalline to amorphous ones is achieved through a simple acid etching treatment. Importantly, compared with the polycrystalline one, the amorphous CoW-LDH (a-CoW-LDH) nanosheets possess higher ROS generation activity under US irradiation, which is ≈17 times of the commercial TiO2 sonosensitizer. The results suggest that the enhanced performance of ultrathin a-CoW-LDH nanosheets for US-induced ROS generation may be attributed to the phase transformation-induced defect generation and electronic structure changes. After polyethylene glycol modification, the a-CoW-LDH nanosheets can serve as a high-efficiency sonosensitizer for SDT to achieve cell death in vitro and tumor eradication in vivo under US irradiation.

Improving epoxy adhesion with steel adherends using a tannic acid‐based additive: Impact on resin properties and interfacial bonding

AbstractTraditional adherend surface treatment techniques such as grit blasting, acid etching, phosphating and primer treatments alone are often inadequate for maintaining interfacial bond durability of adhesively bonded joints. Therefore, the existing interfacial bonds between epoxy adhesive and the adherend should be strengthened. Tannic acid (TA) is a plant‐based polyphenol that is inexpensive and easily available in nature. Its potential as an additive to improve the interfacial bond durability of epoxy adhesives has not been studied adequately. In the present study, an additive (TA‐AGE) was synthesized by grafting allyl glycidyl ether (AGE) onto phenolic hydroxyl groups of TA. With 1 wt% TA‐AGE additive in the epoxy, the single lap shear strength improved by 37%. Further, accelerated aging studies were performed to understand the impact of water uptake on the mechanical and viscoelastic properties and interfacial bond durability of the epoxy with 1 wt% TA‐AGE additive. TA‐AGE modification can increase hydrophilicity and enhance the water uptake characteristics of epoxy. This can negatively impact its mechanical properties and glass transition temperature (Tg) due to plasticization effects. Nevertheless, Boeing wedge test and single lap shear tests reveal that the strengthened interfacial bonds to steel adherends with the additive were robust and durable.