AbstractWe fabricated anti‐glare (AG) coatings on glass sheets by spraying alkoxide‐derived silica sols and demonstrated that the water‐to‐alkoxide ratio is one of the key factors for improving AG performance and sol stability. We synthesized silica sols using tetraethylorthosilicate (TEOS), water, nitric acid, and denatured ethanol and sprayed them on sheets of chemically strengthened glass. The molar ratios of water to TEOS (r) were 3, 7, and 14. The sol with r = 7 provided a higher arithmetic‐mean height (Sa), smaller autocorrelation length (Sal), and better optical properties (lower gloss, higher haze, and lower sparkle level) than the sol with r = 3. An excessive amount of water at r = 14 yielded a large Sal and a high sparkle level. As the storage time of the sols increased, higher r values caused a more pronounced increase in Sa. Although none of the sols showed noticeable temporal changes during dynamic light scattering measurements, solutions with higher r values exhibited a more remarkable reduction in the retention time during liquid chromatography with a styrene‐divinylbenzene matrix. Hence, an excessive amount of water was thought to cause hydrophilization of the polymerized species during storage.

AbstractThe sodium aluminosilicate (NAS) glass family is important for many different industrial applications, but glass relaxation has not yet been thoroughly studied in this system. Thermal analysis techniques such as differential scanning calorimetry (DSC) and modulated differential scanning calorimetry (MDSC) can provide insight into the enthalpy relaxation of glass by measuring the glass transition temperature (Tg), activation energy, and enthalpy of relaxation. MDSC is mostly used to study nonoxide and low Tg glasses, and there is much debate about whether the nonreversing heat flow analysis method is accurate. To the authors’ knowledge, this is the first paper using MDSC to study these NAS compositions, and one of few papers to report MDSC on high Tg oxide glasses. We report on one set of modulation conditions that obtain a linear response using Lissajous curves, as well as comparing the activation energy calculated from DSC with the enthalpy of relaxation obtained from MDSC. Our results show that the activation energy and enthalpy of relaxation do not give the same compositional minimum in relaxation, and therefore more work is needed to investigate the validity of the nonreversing heat flow approach for high Tg oxide glasses.

AbstractTransparent lithium aluminum silicon glass‐ceramics are prepared via heat treatment and the effect of boron oxide (B2O3) content on the structure and properties of Li2O‐Al2O3‐SiO2 glass‐ceramics is investigated. The X‐ray photoelectron spectroscopy results reveal that the parent glass containing B2O3 exhibits a higher concentration of bridging oxygen (BO). With an increase in B2O3 content, the relative amount of BO changes from 76.64% to 79.86% and then to 79.52%. Simultaneously, the second crystallization peak temperature TP2 of the samples increases from 715°C to 720°C and then to 724°C by differential scanning calorimeter analysis. The X‐ray diffractometer and scanning electron microscope results indicate that the addition of B2O3 facilitates grain growth, while an increase in B2O3 substitution for Al2O3 hinders the precipitation of LiAlSi4O10 but promotes quartz formation. The glass containing 2 wt% B2O3 with the heat treatment of 560°C/ 4 h+ 680°C/2 h shows a Vickers Hardness value of approximately 7.75 GPa, and a transmittance at 550 nm reaching ∼85%.

AbstractPhotovoltaic (PV) modules are a key technology to aid the imminent transition from carbon‐based energy. End‐of‐life crystalline silicon PV modules produce a waste stream that is predominantly landfilled due to the recycling challenges associated with PV reuse economics. Current practices recycle the aluminum frame and repurpose the junction box but landfill the rest of the module. The primary challenge in recycling the remaining module is finding a technoeconomically viable method for separating the silicon and glass from the ethylene vinyl acetate (EVA) layers. This issue will rapidly expand with time as it is estimated that flat glass production for solar panels is currently unable to meet the demand for PV. Current literature suggests that chemical, thermal, and mechanical delamination offer economically feasible solutions under ideal circumstances. In this work we evaluate these methods using end‐of‐life panels and assess the economic viability. The technoeconomic study presented here suggests the most economically viable option for disposing of end‐of‐life solar panels, given current technology, is landfilling. Thermal delamination may offer an alternative route in the future. Financial incentives, which can be quantified with this work, may be required to kickstart PV recycling to help bridge externalities around environmental impact.

AbstractA two‐dimensional (2D) axisymmetric numerical model, based on the finite element method, for glass containers forming processes is presented. Glass forming processes involve coupled thermomechanical phenomena in which heat transfer and viscous flow are dependent, as glass viscosity is highly dependent on temperature. During the overall process glass changes from a molten state to a solid state. Therefore, adequate cooling conditions must be set appropriately. From the numerical point of view, the modeling must be robust so as to adjust to the different sequenced stages. Remeshing techniques requiring adequate data transfer, as well as, different thermal and mechanical contact conditions between glass and molds must be taken into account. Also, effective treatment of the incompressible conditions associated with glass flow must be dealt with. The aim is to set the better process parameters so that the final containers have the required geometrical shape and thickness distribution. A numerical model was conducted addressing all these issues and a thickness distribution comparison with real industrial products was performed.

AbstractContact damage of glass is one of the most crucial issues for glass products. To develop strong and tough glass products and to compare damage resistance among glass compositions, a simple method for evaluating the mechanical response of glass during contact is required not only for glass mechanists but also for glass customers and suppliers. Although it is well known that the quasi‐static Vickers indentation test is one of the simplest and most useful methods to evaluate hardness and brittleness in glass, the indentation response of glass under the indenter at higher impact velocities remains to be quantitively understood because of the difficulty of measurement and limited experimental works. In this study, therefore, the dynamic indentation behavior of soda‐lime glass is evaluated by using a lab‐made free‐drop indentation set‐up with the coils for detecting electromotive forces (EMFs). The cono‐spherical indenter made of tungsten carbide attached with a neodymium magnet was employed to generate the EMFs when the indenter passed through the coils located near the glass sample. The impact load versus indentation depth curve during the impact within a few tens of microseconds was successfully obtained both for an elastic contact and for an inelastic contact. Under an elastic condition, where no residual indent nor any cracks were left on the glass surface after the test, it is confirmed that there is almost no hysteresis in the impact load versus indentation depth curve and that the curve can be reproduced by the Hertzian analytical solution. Under an inelastic condition, on the other hand, it is found that the hysteresis in the impact load versus indentation depth curve stems from inelastic phenomena, such as plastic deformation (shear flow and/or permanent densification) and cracking. These results suggest that the dynamic indentation technique based on electromagnetic induction phenomena is a useful and effective tool for evaluating the mechanical responses of glasses during the impact.