The presence of a variety of pollutants in the aquatic environment that can potentially interfere with the production of sex steroid hormones in wildlife and humans has been of increasing concern. The aim of the present study was to investigate the effects of extracts from Hong Kong marine waters, and influents and effluents from wastewater treatment plants on steroidogenesis using the H295R cell bioassay. After exposing H295R cells to extracts of water, the expression of four steroidogenic genes and the production of three steroid hormones were measured. Water samples were collected during the summer of 2005 from 24 coastal marine areas and from the influents and effluents of two major waste water treatment plants (WWTPs) in Hong Kong, China. Samples were extracted by solid phase extraction (SPE). H295R cells were exposed for 48 h to dilutions of these extracts. Modulations of the expression of the steroidogenic genes CYP19, CYP17, 3betaHSD2, and CYP11beta2 were determined by measuring mRNA concentrations by real-time polymerase chain reaction (Q-RT-PCR). Production of the hormones progesterone (P), estradiol (E2), and testosterone (T) was quantified using enzyme linked immunosorbent assays (ELISA). Extracts from samples collected in two fish culture areas inhibited growth and proliferation of H295R cells at concentrations greater or equal to 10(5) L equivalents. The cells were exposed to the equivalent concentration of active substances in 10,000 L of water. Thus, to observe the same level of effect as observed in vitro on aquatic organisms would require a bioaccumulation factor of this same magnitude. None of the other 22 marine samples affected growth of the cells at any dilution tested. Twelve of the marine water samples completely inhibited the expression of CYP19 without affecting E2 production; inhibition of CYP17 expression was observed only in one of the samples while expression of CYP11beta2 was induced as much as five- and ninefold after exposure of cells to extracts from two locations. The expression of the progesterone gene 3betaHSD2 was not affected by any of the samples; only one sample induced approximately fourfold the production of E2. Although more than twofold inductions were observed for P and T production, none of these values were statistically significant to conclude effects on the production of these two hormones. While influents from WWTPs did not affect gene expression, an approximately 30% inhibition in the production of E2 and a 40% increase in P occurred for the exposure with influents from the Sha Tin and Stonecutters WWTPs, respectively. Effluents from WWTPs did not affect the production of any of the studied hormones, but a decrement in the expression of the aldosterone gene CYP11beta2 was observed for the Sha Tin WWTP exposure. No direct correlation could be established between gene expression and hormone production. Observed cytotoxicity in the two samples from fish culture areas suggest the presence of toxic compounds; chemical analysis is required for their full identification. Although effluents from WWTPs did not affect hormone production, other types of endocrine activity such as receptor-mediated effects cannot be ruled out. Interactions due to the complexity of the samples and alternative steroidogenic pathways might explain the lack of correlation between gene expression and hormone production results. Changes observed in gene expression and hormone production suggest the presence in Hong Kong coastal waters of pollutants with endocrine disruption potential and others of significant toxic effects. The aromatase and aldosterone genes seem to be the most affected by the exposures, while E2 and P are the hormones with more significant changes observed. Results also suggest effectiveness in the removing of compounds with endocrine activity by the WWTPs studied, as effluent samples did not significantly affect hormone production. The H295R cell showed to be a valuable toll in the battery required for the analysis of endocrine disrupting activities of complex environmental samples. Due to the intrinsic complexity of environmental samples, a combination of analytical tools is required to realistically assess environmental conditions, especially in aquatic systems. In the evaluation of endocrine disrupting activities, the H295R cell bioassay should be used in combination with other genomic, biological, chemical, and hydrological tests to establish viable modes for endocrine disruption and identify compounds responsible for the observed effects.

BACKGROUND, GOALS AND SCOPE: Risk assessment of herbicides and the evaluation of contaminated sediments based on algae and the macrophyte Lemna sp. alone may underestimate the potential hazard of certain compounds. Therefore, various test systems with Myriophyllum spp. have been developed recently to assess the phytotoxicity in surface waters and natural sediments. In the present study, experiments investigating the growth development of Myriophyllum spp. were performed in the laboratory under defined conditions and in mesocosms under environmentally realistic exposure conditions to evaluate the suitability of these species as potential standard test organisms in ecotoxicological testing. This study provides data on the endpoints biomass, plant length and root development. Six independent experiments were performed to investigate the plant development of Myriophyllum spp. under control conditions. The main difference in the experiments was the complexity of the test systems ranging from simple laboratory experiments to complex outdoor mesocosm studies. At the start of each experiment, uniform cuttings of Myriophyllum spp. were placed in vessels with or without sediments to reduce variability between replicates. The endpoints considered in this investigation were biomass (fresh weight of the whole plant), length of the main shoot, length of the side shoots, total length of the plant (calculated from the length of the main and side shoots) and root formation. Root to shoot ratios were calculated as a further measure for plant development. Relative growth rates (RGR) based on plant length (RG(L)R) and on biomass (RG(B)R) were calculated. Despite the various experimental conditions, comparable growth was obtained in all test systems and the variability of endpoints, such as total length and biomass of plants, was low. It was observed that the RGR of M. spicatum in the simple laboratory test system with sediment were comparable to growth data obtained for M. verticillatum and M. spicatum grown in indoor and outdoor mesocosms, thus indicating that Myriophyllum growth tends to increase by the addition of sediment. High variability was determined for the endpoints length of the side shoots, total root length and biomass of roots. One challenge for a test design to investigate phytotoxicity on aquatic plants is to obtain good growth of the plants. From the results, it can be concluded that the experimental conditions in the various test systems were suitable to study the plant development of Myriophyllum spp. because obtained growth rates were comparable between laboratory and field investigations. Another challenge for developing a plant biotest system is the definition of sensitive endpoints. Low variability is preferred to detect minor effects of chemicals or polluted sediments on plant development. In our studies, the variability of the endpoints biomass and total length of plant was low and, therefore, they have much potential as endpoints for assessing toxicity. The methodologies presented in this study have applications within the risk assessment for aquatic plants and have the advantage of assessing effects taking into account the relevant exposure pathways via water and/or sediment for compounds under investigation. Setting safe quality criteria for surface water and sediments is one of the challenges authorities are facing today. Myriophyllum spp. is recommended as suitable test species to investigate phytotoxicity in surface water and sediments. These results, thus, might serve as a basis for the compilation of a new harmonised guideline for ecotoxicological testing with aquatic macrophytes.

Large quantities of biosolids (sewage sludge), which are produced from municipal wastewater treatment, are ever-increasing because of the commissioning of new treatment plants and continuous upgrades of the existing facilities. A large proportion of biosolids are currently landfilled. With increasing pressure from regulators and the general public, landfilling of biosolids is being phased out in many countries because of potential secondary pollution caused by leachate and the emission of methane, a potent greenhouse gas. Biosolids contain nutrients and energy that can be used beneficially. Significant efforts have been made recently to develop new technologies to manage biosolids and make useful products from them. In this paper, we provide a review of the technologies in biosolids management. A survey of literature was conducted. At present, the most common beneficial use of biosolids is agricultural land application because of inherent fertilizer values found in biosolids. Expansion of land application, however, may be limited in the future because of more stringent regulatory requirements and public concern about food chain contamination in some countries. Perceived as a green energy source, the combustion of biosolids has received renewed interest. Anaerobic digestion is generally a more effective method than incineration for energy recovery, and digested biosolids are suitable for further beneficial use through land application. Although conventional incineration systems for biosolid management generally consume more energy than they produce because of the high moisture content in the biosolids, it is expected that more combustion systems, either monocombustion or cocombustion, will be built to cope with the increasing quantity of biosolids. Under the increasingly popular low-carbon economy policy, biosolids may be recognized as a renewable fuel and be eligible for 'carbon credits'. Because ash can be used to manufacture construction materials, combustion can provide a complete management for biosolids. A number of advanced thermal conversion technologies (e.g., supercritical water oxidation process and pyrolysis) are under development for biosolids management with a goal to generate useful products, such as higher quality fuels and recovery of phosphorus. With an ever-increasing demand for renewable energy, growing bioenergy crops and forests using biosolids as a fertilizer and soil amendment can not only contribute to the low-carbon economy but also maximize the nutrient and carbon value of the biosolids. Land application of biosolids achieves a complete reuse of its nutrients and organic carbon at a relatively low cost. Therefore, land application should become a preferred management option where there is available land, the quality of biosolids meet regulatory requirements, and it is socially acceptable. Intensive energy cropping and forest production using biosolids can help us meet the ever-increasing demand for renewable energy, which can eliminate the contamination potential for food sources, a common social concern about land application of biosolids. In recent years, increasing numbers of national and local governments have adopted more stringent regulations toward biosolid management. Under such a political climate, biosolids producers will have to develop multireuse strategies for biosolids to avoid being caught because a single route management practice might be under pressure at a short notice. Conventional incineration systems for biosolids management generally consume more energy than they produce and, although by-products may be used in manufacturing, this process cannot be regarded as a beneficial use of biosolids. However, biosolids are likely to become a source of renewable energy and produce 'carbon credits' under the increasingly popular, low-carbon economy policy. To manage biosolids in a sustainable manner, there is a need for further research in the following areas: achieving a higher degree of public understanding and acceptance for the beneficial use of biosolids, developing cost-efficient and effective thermal conversions for direct energy recovery from biosolids, advancing technology for phosphorus recovery, and selecting or breeding crops for efficient biofuel production.

Asymmetrical convective non-local scheme (CON) with varying upward mixing rates is developed for simulation of vertical turbulent mixing in the convective boundary layer in air quality and chemical transport models. The upward mixing rate form the surface layer is parameterized using the sensible heat flux and the friction and convective velocities. Upward mixing rates varying with height are scaled with an amount of turbulent kinetic energy in layer, while the downward mixing rates are derived from mass conservation. This scheme provides a less rapid mass transport out of surface layer into other layers than other asymmetrical convective mixing schemes. In this paper, we studied the performance of a nonlocal convective mixing scheme with varying upward mixing in the atmospheric boundary layer and its impact on the concentration of pollutants calculated with chemical and air-quality models. This scheme was additionally compared versus a local eddy-diffusivity scheme (KSC). Simulated concentrations of NO(2) and the nitrate wet deposition by the CON scheme are closer to the observations when compared to those obtained from using the KSC scheme. Concentrations calculated with the CON scheme are in general higher and closer to the observations than those obtained by the KSC scheme (of the order of 15-20%). Nitrate wet deposition calculated with the CON scheme are in general higher and closer to the observations than those obtained by the KSC scheme. To examine the performance of the scheme, simulated and measured concentrations of a pollutant (NO(2)) and nitrate wet deposition was compared for the year 2002. The comparison was made for the whole domain used in simulations performed by the chemical European Monitoring and Evaluation Programme Unified model (version UNI-ACID, rv2.0) where schemes were incorporated.

Polycyclic aromatic hydrocarbons (PAHs) are widespread environmental contaminants and contribute to the pollution of soil environment. Soil ingestion is of increasing concern for assessing health risk from PAH-contaminated soils because soil ingestion is one of the potentially important pathways of exposure to environmental pollutants, particularly relevant for children playing at contaminated sites due to their hand-to-mouth activities. In vitro gastro-intestinal tests imitate the human digestive tract, based on the physiology of humans, generally more simple, less time-consuming, and especially more reproducible than animal tests. This study was conducted to investigate the level of PAH contamination and oral bioaccessibility in surface soils, using physiologically based in vitro gastro-intestinal tests regarding both gastric and small intestinal conditions. Wastewater-irrigated soils were sampled from the metropolitan areas of Beijing and Tianjin, China, which were highly contaminated with PAHs. Reference soil samples were also collected for comparisons. At each site, four soils were sampled in the upper horizon at the depth of 0-20 cm randomly and were bulked together to form one composite sample. PAH concentrations and origin were investigated and a physiologically based in vitro test was conducted using all analytical grade reagents. Linear regression model was used to assess the relationship between total PAH concentrations in soils and soil organic carbon (SOC). A wide range of total PAH concentrations ranging from 1,304 to 3,369 mug kg(-1) in soils collected from different wastewater-irrigated sites in Tianjin, while ranging from 2,687 to 4,916 mug kg(-1) in soils collected from different wastewater-irrigated sites in Beijing, was detected. In general, total PAH concentrations in soils from Beijing sites were significantly higher than those from Tianjin sites, indicating a dominant contribution from both pyrogenic and petrogenic sources. Results indicated that the oral bioaccessibility of PAHs in small intestinal was significantly higher (from P < 0.05 to P < 0.001) than gastric condition. Similarly, the oral bioaccessibility of PAHs in contaminated sites was significantly higher (from P < or = 0.05 to P < 0.001) than in reference sites. Individual PAH ratios (three to six rings), a more accurate and reliable estimation about the emission sources, were used to distinguish the natural and anthropogenic PAH inputs in the soils. Results indicated that PAHs were both pyrogenic and petrogenic in nature. The identification of PAH sources and importance of in vitro test for PAH bioaccessibility were emphasized in this study. The oral bioaccessibility of individual PAHs in soils generally decreased with increasing ring numbers of PAHs in both the gastric and small intestinal conditions. However, the ratio of bioaccessibility of individual PAHs in gastric conditions to that in the small intestinal condition generally increased with increasing ring numbers, indicating the relatively pronounced effect of bile extract on improving the bioaccessibility of PAHs with relatively high ring numbers characterized by their high K ( ow ) values. Similarly, total PAH concentrations in soils were strongly correlated with SOC, indicating that SOC was the key factor determining the retention of PAHs in soils. Soils were contaminated with PAHs due to long-term wastewater irrigation. PAHs with two to six rings showed high concentrations with a significant increase over reference soils. Based on the molecular indices, it was suggested that PAHs in soils had both pyrogenic and petrogenic sources. It was also concluded that the oral bioaccessibility of total PAHs in the small intestinal condition was significantly higher than that in the gastric condition. Furthermore, the bioaccessibility of individual PAHs in soils generally decreased with the increasing ring numbers in both the gastric and small intestinal conditions. It is suggested that more care should be given while establishing reliable soil criteria for PAHs, especially concerning the health of children who may ingest a considerable amount of PAH-contaminated soil via outdoor hand-to-mouth activities.

Arsenic contamination in groundwater creates severe health problems in the world. There are many physiochemical and biological methods available for remediation of arsenic from groundwater. Among them, microbial remediation could be taken as one of the least expensive methods, though it takes longer treatment time. The main objective of this research was to study the improvement on remediation by addition of some essential ion salts such as Mn and Fe. Staphylococcus aureus, Bacillus subtilis, Klebsiella oxytoca, and Escherichia coli were taken as model microbes from Dhulikhel, 30 km east from Kathmandu, Nepal. Microbes used in this study showed different abilities in their removal of As(III) with and without addition of Mn and Fe salts. The trend of remediation increased with time. S. aureus was found to be the best among the microbes used. It showed almost 100% removal after 48-h culture, both with and without Fe and Mn salts. Rate of removal of As increased with addition of Fe and Mn for all microbes. Removal efficiency was found to increase by about 32% on average after addition of salts in 24-h cultures of S. aureus.

Current leather processing method involves dehairing and fibre opening employing lime and sulphide, which results in higher negative impact on the environment due to its uncleanness. This method of dehairing and fibre-opening process accounts for nearly 70-80% biochemical oxygen demand and chemical oxygen demand (COD) in tannery wastewater and also the generation of H(2)S gas. Hence, an attempt has been made to reduce the environmental impact of the leather processing through a biochemical approach, employing proteolytic enzyme and sodium metasilicate for performing the above process more cleanly. The developed process exhibits significant reduction in environmental parametres such as COD and total solid loads by 55% and 25%, respectively. This method completely avoids the formation of lime sludge. The functional properties of the leathers are also on par with conventionally processed leathers. Further, the process seems to be commercially viable.