Ultrathin Co3O4 Layers Realizing Optimized CO2 Electroreduction to Formate.

Electroreduction of CO2 into hydrocarbons could contribute to alleviating energy crisis and global warming. However, conventional electrocatalysts usually suffer from low energetic efficiency and poor durability. Herein, atomic layers for transition‐metal oxides are proposed to address these problems through offering an ultralarge fraction of active sites, high electronic conductivity, and superior structural stability. As a prototype, 1.72 and 3.51 nm thick Co3O4 layers were synthesized through a fast‐heating strategy. The atomic thickness endowed Co3O4 with abundant active sites, ensuring a large CO2 adsorption amount. The increased and more dispersed charge density near Fermi level allowed for enhanced electronic conductivity. The 1.72 nm thick Co3O4 layers showed over 1.5 and 20 times higher electrocatalytic activity than 3.51 nm thick Co3O4 layers and bulk counterpart, respectively. Also, 1.72 nm thick Co3O4 layers showed formate Faradaic efficiency of over 60 % in 20 h.

Mixed ionic-electronic conducting polymers (MIECPs) show promise for next-generation electrochemical devices due to the unique ability to simultaneously conduct both ions and electrons. However, there is a trade-off between electronic and ionic conduction because of their opposite morphology dependence. Here, we report simultaneous high electron-conduction and high ion-conduction in thin films of supramolecular MIECPs through the liquid crystalline (LC) assembly pathway from solution to the solid state. The supramolecular MIECPs are prepared via non-covalent bonding between carboxylated poly-(3-alkyl thiophene)-s and an imidazolium-based ionic liquid (IL) surfactant and characterized by means of UV-visible (UV-vis) absorption spectroscopy, polarized optical microscopy (POM) and small-angle X-ray scattering (SAXS). After complexation, the system displays colorimetric transitions and optoelectronic changes with the IL surfactant mole ratio. At equal stoichiometry, the polymer displays a rodlike conformation with planarization of the conjugated backbone. The hydrogel of the equimolar solution exhibits a typical LC polydomain texture with strong birefringence under POM, which is identified as a smectic LC mesophase with lamellar periodicity using SAXS. Defect-free LC monodomains containing unidirectional alignment are obtained in the hydrogel through mechanical shearing. After complete solvent evaporation, the LC monodomain structures are retained in the solid-state film, resulting in simultaneously high electronic (10-2- 10-1 mS/cm) and ionic (10-3 - 10-2 mS/cm) conductivities at ambient temperature. Generally, the block copolymers of MIECPs show high ionic conductivities (10-2 - 1 mS/cm) but low electronic conductivities (10-5 - 10-2 mS/cm). While the homopolymers of MIECPs display high electronic conductivity (10-6 - 102 mS/cm) but low ionic conductivity (10-6 - 10-2 mS/cm). In addition, aligned solid-state films show a significant anisotropy in both electronic (anisotropic ratio of ∼6) and ionic (anisotropic ratio of ∼117) conductivities, with faster charge transport along the shear direction than the perpendicular direction. It is believed that aligned conjugated backbones along the shear direction provide channels for fast band-like transport of electronic charge carriers and aligned imidazolium moieties in the lamellar layers form constrained channels for ion motion.

Functional electrodes for batteries share a common design rule by which high electronic and ionic conductivity pathways must exist throughout the electrode in its pristine state. Notable amounts of conductive carbon additive in the composite electrode are usually included to form an electronically conductive matrix. However, excellent high rate cycling performance has been achieved in electrodes composed of the insulating Li4Ti5O12 without any conductive additives. This behavior opens the possibility of a new paradigm for designing functional electrodes by which high electronic conductivity in the pristine electrode is not required. The mechanism of operation that enables such unexpected electrochemical behavior is evaluated and discussed. Electronically conductive pathways due to the reduction of Ti4+ to Ti3+ form and percolate throughout the Li4Ti5O12 electrode in the early stage of Li insertion, eliminating the need for conductive additives. This work highlights the importance of the mass and charge transport properties of the intermediate states during cycling and of good interparticle ohmic contact in the electrode. This physical behavior can lead to novel system designs with improved battery utilization and energy density.

Improving oxygen permeation of MIEC membrane reactor by enhancing the electronic conductivity under intermediate-low oxygen partial pressures

Operando leaching of pre-incorporated Al and mechanism in transition-metal hybrids on carbon substrates for enhanced charge storage

Open AccessCCS ChemistryRESEARCH ARTICLE25 May 2022Controlled Growth Interface of Charge Transfer Salts of Nickel-7,7,8,8-Tetracyanoquinodimethane on Surface of Graphdiyne Yuxin Liu, Yang Gao, Feng He, Yurui Xue and Yuliang Li Yuxin Liu Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190 University of Chinese Academy of Sciences, Beijing 100049 , Yang Gao Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190 University of Chinese Academy of Sciences, Beijing 100049 , Feng He Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190 University of Chinese Academy of Sciences, Beijing 100049 , Yurui Xue *Corresponding authors: E-mail Address: [email protected]; E-mail Address: [email protected] Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190 Science Center for Material Creation and Energy Conversion, School of Chemistry and Chemical Engineering, Institute of Frontier and Interdisciplinary Science, Shandong University, Jinan 250100 and Yuliang Li *Corresponding authors: E-mail Address: [email protected]; E-mail Address: [email protected] Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190 University of Chinese Academy of Sciences, Beijing 100049 https://doi.org/10.31635/ccschem.022.202202005 SectionsSupplemental MaterialAboutAbstractPDF ToolsAdd to favoritesDownload CitationsTrack Citations ShareFacebookTwitterLinked InEmail Here we report an in situ assembly growth method that controls the growth of NiTCNQ on the surface of graphdiyne (GDY). The catalytic system of donor–acceptor–donor (GDY/TCNQ/Ni) structure with multiple charge transfer (CT) was achieved by controlling the growth of NiTCNQ on the surface of GDY. Significantly, a controlled double layer interface of GDY/TCNQ/Ni was formed. This system implemented simultaneously the two elements we expected (1) an incomplete CT, and (2) the infinite distribution of active sites originating from highly asymmetric surface charge distribution. The high conductivity and typical semiconductor characteristics of the catalyst endows it with high catalytic activity. We found that an electrolytic cell consisting of the CT salt as a catalyst provided a 1.40 V ultra-small cell voltage up to 10 mA cm−2 and the outer GDY film effectively prevented the corrosion of the catalyst. Our study is the first to introduce CT complexes to a novel catalytic material platform for high selectivity of catalysts, and undoubtedly demonstrates the high selectivity, stability, and activity of such catalytic systems, which provides a new space for the development of novel conceptual catalysts. Download figure Download PowerPoint Introduction The sustainable hydrogen (H2) production through electrocatalytic overall water splitting (OWS) provides a promising method to overcome the global energy crisis and environmental problems, which is of great significance for industrial and scientific progress.1,2 In terms of hydrogen conversion, precious metal-based materials (e.g., Ru or Ir-based materials for the oxygen evolution reaction (OER); Pt-based materials for the hydrogen evolution reaction (HER)) remain the benchmark catalysts with high catalytic performances, but they are not suitable for large-scale commercialization due to their high cost, low abundance, and insufficient stability. At present, the high cost of precious metals has seriously restricted the development of this field. Transition metal-based materials, such as metal hydroxides, oxides, nitrides, phosphides, carbides, and sulfides, have been extensively studied for anodic OER and cathodic HER.3–6 However, the low catalytic activity of these systems results in sluggish kinetics of OER and HER. In addition, there is no stability advantage of these catalysts. Furthermore, to meet the requirement of industrial alkaline water splitting for hydrogen production, the catalysts should produce large current densities at low cell voltages (e.g., ∼200–400 mA cm−2 at 1.8–2.4 V) and be synthesized from earth-abundant elements to minimize the H2 production cost.7–10 Therefore, to develop catalysts with excellent comprehensive performance, we need to find a new way to produce electrocatalysts with low cost, high activity, and high stability. The unique and excellent structures and properties of graphdiyne (GDY) has triggered extensive investigations on its fundamental properties and potential applications in various research fields, such as catalysis, energy conversion and storage, optical and electrical devices, and so on.11–26 As a new sp- and sp2-cohybridized two-dimensional carbon material, GDY shows large porous structure, high intrinsic activity, excellent electron transfer ability, high electronic conductivity, and high stability.27–29 GDY is an ideal carbon material for synthesizing high-performance catalysts with determined structures and abundant active sites, and provides the opportunities for clearly understanding the relationship of structure and performance. GDY can be grown on arbitrary substrates at low temperatures and ambient pressures, which protects the parent structure and the active site structure from destruction and generates new active sites. 7,7,8,8-Tetracyanoquinodimethane (TCNQ) is a well-known electron acceptor with high electron affinity, which easily reacts with metal atoms to form charge transfer (CT) complexes with high conductivity, high carrier density, and special electron transport properties.30 Metal-TCNQs show excellent electrical and optical properties, and unique and adjustable electron and high CT ability. CT complexes where the CT amount is not an integer is called incomplete CT; it is different from traditional inorganic complexes with an integer CT. Because of their high conductivity and semiconductor characteristics, they have attracted more and more interest in many research fields.31–34 However, until now, research on CT complexes mainly focused on controlled growth, photoelectric devices. and semiconductor properties, while basic and applied research in the field of catalysis remain silent. Recently, we took NiTCNQ–GDY as an example and explored the basis and application of NiTCNQ–GDY as an emerging catalyst in hydrogen energy conversion. In addition, we deeply understand the GDY plays the key role in the generation of efficient catalysts, and find its introduction overcomes important issues such as solvent corrosion, structural instability caused by light or electricity, and poor conductivity.35,36 In this work, we report the successful synthesis of a donor–acceptor–donor (GDY/TCNQ/–Ni) structure with multiple CT by in situ growing GDY layers on the surface of NiTCNQ nanowires (GDY–NiTCNQ). Experimental results demonstrated the incomplete CT and the infinite distribution of active sites originating from highly asymmetric surface charge distribution endow the catalyst with high conductivity, typical semiconductor characteristics, high catalytic activity, and excellent intrinsic properties. These unique and fascinating properties endow GDY–NiTCNQ with excellent catalytic activities toward OER, HER, and OWS. For instance, GDY–NiTCNQ exhibited small overpotentials of 218 and 61 mV at 10 mA cm−2 for OER and HER in 1.0 M KOH. When used as an electrolytic cell, it can drive 10 mA cm−2 at a low cell voltage of 1.40 V. This work provides a new direction toward the development of cost-effective and high-performance electrocatalysts. Experimental Methods Material TCNQ was purchased from Tokyo Chemical Industry (TCI, Shanghai, China). Acetonitrile and methanol were obtained from Concord Technology (Tianjin) Co., Ltd. Nickel foams (NFs) were treated with dilute hydrochloric acid, rinsed with deionized water, and dried with N2 flow before use. Deionized water was purified with a Millipore system. All chemicals were analytical grade and used without further purification unless otherwise specified. Preparation of NiTCNQ in acetonitrile A piece of freshly pretreated nickel film (3 cm × 1.5 cm) was immersed in 10 mM TCNQ acetonitrile solution for 10 min followed by the addition of 3% deionized water at room temperature. After reaction for 6 h, the material was removed from the solution, washed carefully with acetonitrile and water, and dried under the protection of N2. Preparation of GDY on NiTCNQ (GDY–NiTCNQ) A piece of NiTCNQ was immersed in 50 mL acetone solution of hexaethynylbenzene (HEB) at 50 °C under Ar atmosphere protected from light. After reaction for 12 h, the resulting GDY–NiTCNQ was washed with acetone, deionized water, and acetone, followed by drying at 50 °C in a vacuum oven. Characterization The morphology of the material was characterized by scanning electron microscopy (SEM; Hitachi, S 4800; Institute of Chemistry, Chinese Academy of Sciences), transmission electron microscopy (TEM, a JEOL JEM-2100F field-emission high-resolution transmission electron microscope at an accelerating voltage of 200 kV; Institute of Chemistry, Chinese Academy of Sciences), and high-resolution TEM (HRTEM). The energy-dispersive spectroscopy (EDS) mapping analysis was also obtained to characterize the elemental composition of the samples. X-ray diffraction (XRD) measurements were carried out on a PANalytical high-resolution XRD system (EMPYREAN) using Cu Kα radiation (λ = 1.540598 mm). X-ray photoelectron spectroscopy (XPS) was performed on a Thermo Scientific ECSALab 250Xi instrument with monochromatic Al Kα X-ray radiation (Institute of Chemistry, Chinese Academy of Sciences). Electrochemical measurements All electrochemical tests were carried out using an electrochemical workstation (CHI 760E) through a typical three-electrode system, in which the as-prepared samples, graphite rods, and saturated calomel electrode were used as the working electrode, the counter electrode, and the reference electrode, respectively. All the electrolytes used in the experiments were bubbled with Ar for 2 h before use. Linear sweep voltammetry (LSV) measurements were carried out at a scan rate of 2 mV s−1 in 1.0 M KOH solution. Cyclic voltammetry (CV) measurements were carried out at a scan rate of 100 mV s−1. Electrochemical impedance spectroscopy (EIS) was obtained at the frequency range of 100 KHz to 0.1 Hz with a sampling rate of 12 points per decade, and the data obtained was fitted. All potentials were converted to the reversible hydrogen electrode (RHE) according to ERHE = ESCE + E0SCE + 0.059 × pH. X-ray absorption fine structure measurements The X-ray absorption fine structure (XAFS) spectra (Ni K-edge) were collected at 1W1B station in Beijing Synchrotron Radiation Facility (BSRF). The storage rings of BSRF were operated at 2.5 GeV with an average current of 250 mA. Using a Si(111) double-crystal monochromator, the data collection was carried out in transmission/fluorescence mode using an ionization chamber. All spectra were collected in ambient conditions. XAFS analysis and results The acquired extended XAFS (EXAFS) data were processed according to the standard procedures using the ATHENA module implemented in the IFEFFIT software packages. The k3-weighted EXAFS spectra were obtained by subtracting the post-edge background from the overall absorption and then normalizing with respect to the edge-jump step. Subsequently, k3-weighted χ(k) data of Ni K-edge were Fourier transformed to real (R) space using a Hanning windows (dk = 1.0 Å−1) to separate the EXAFS contributions from different coordination shells. To obtain the quantitative structural parameters around central atoms, least–squares curve parameter fitting was performed using the ARTEMIS module of the IFEFFIT software packages. Results and Discussion As shown in Figures 1a and 1b, a two-step in situ growth strategy was used to selectively synthesize the GDY–NiTCNQ catalysts with D–A–D (GDY/TCNQ/Ni) structure, including the first in situ growth of NiTCNQ nanorods and the subsequent growth of the GDY film on the outer layer of the NiTCNQ nanorods that leads to the formation of GDY–NiTCNQ nanowires. Typically, with the dropwise addition of water into the acetonitrile solution of TCNQ, the Ni ions released from the substrate and then interacted with TCNQ forming the A–D (TCNQ–Ni) structure. The NiTCNQ assembled into highly ordered NiTCNQ-nanorods array on the surface of NF.37 The NiTCNQ was then immersed into the acetone solution, after which the HEB precursor was added to grow GDY films on the NiTCNQ surface with the morphology gradually changing from nanorod to nanowire. During this process, the D–A–D (GDY/TCNQ/Ni) structure was formed. Figure 1 | Schematic representation of the controlled synthesis route to the catalytic system of donor–acceptor–donor (GDY/TCNQ/Ni) structures through in situ growth of (a) NiTCNQ nanorods and (b) GDY–NiTCNQ. Download figure Download PowerPoint Figure 2a shows that the color of the samples changed from gray for NF to dark green for NiTCNQ and black for GDY–NiTCNQ during the synthetic process. SEM images clearly show that the smooth surface of 3D NF (Figures 2b–2d) was covered by a film of NiTCNQ nanorods (average diameter, ∼210 nm; Figures 2e–2h). As shown in Supporting Information Figure S1, the NiTCNQ has a flat surface and a fringe lattice spacing of 0.254 nm. The electrostatic potential (ESP) of NiTCNQ (Figure 2h) confirms the interactions between Ni ions and TCNQ with evident CT from Ni to TCNQ, which also demonstrates the formation of the A–D structure. With the growing of GDY on the NiTCNQ surface, the morphology of the nanorods of NiTCNQ changed to nanowires for GDY–NiTCNQ (Figures 2i–2l). As revealed by HRTEM images (Figures 2l and 2m), an obvious shell layer was observed outside of the NiTCNQ core, confirming the successful growth of GDY on the surface of NiTCNQ (Figure 2m). GDY–NiTCNQ exhibits a rough and porous surface, which is beneficial for enlarging the active surface area and the number of active sites. The lattice spacing of the core structure of GDY–NiTCNQ is 0.254 nm ( Supporting Information Figure S2), in accordance with the NiTCNQ, indicating the structure of NiTCNQ was well maintained during the GDY growth process. Scanning TEM (STEM) and EDS mapping images (Figures 2n–2q and Supporting Information Table S1) confirm the presence of carbon, nitrogen, and nickel elements in the GDY–NiTCNQ sample without any impurities. Ni and N are densely distributed in the inner space and sparsely distributed in the edge, and C is evenly distributed throughout the whole material. These results demonstrated the formation of the double layer interface of GDY/TCNQ/Ni, and the GDY film on the outer layer can effectively prevent the catalyst corrosion, which guarantees the long-term stability of the catalyst. Figure 2 | Morphological characterizations of GDY–NiTCNQ and NiTCNQ. (a) Photographs of (i) NF, (ii) NiTCNQ, and (iii) GDY–NiTCNQ. SEM images of (b–d) NF, (e–g) NiTCNQ, and (i–k) GDY–NiTCNQ samples. (h) Electrostatic potential of NiTCNQ. TEM images of (l and m) GDY–NiTCNQ. Elemental mapping images (n–p) of C, Ni, and N atoms in the GDY–NiTCNQ. Download figure Download PowerPoint XRD and XPS measurements were performed to characterize the compositions and structures of the samples. As shown in Figure 3a, the intensity of the peaks for GDY–NiTCNQ decreased as compared with that of NiTCNQ, which might be due to the growth of GDY on NiTCNQ. The XPS survey spectra confirm the presence of Ni, C, and N elements in accordance with the EDS result ( Supporting Information Figures S3 and S4). Compared with pure NiTCNQ (Figure 3b), the C 1s XPS spectra of GDY–NiTCNQ shifted to higher binding energies (BE) by 0.75 eV, revealing the CT from GDY to NiTCNQ. The appearance of an sp-C peak in the C 1s spectra of GDY–NiTCNQ (Figure 3c) indicates the successful growth of GDY on NiTCNQ. Moreover, an independent new peak at 291.96 eV originating from the π–π* shakeup satellite implies the interactions between NiTCNQ and GDY.7 In the Ni 2p region (Figure 3d), the peaks for GDY–NiTCNQ decreased by 1.23 eV as compared with that of NiTCNQ ( Supporting Information Figure S5), revealing the remarkable CT between NiTCNQ and GDY. For GDY–NiTCNQ, the peaks for Ni2+ 2p3/2 and Ni2+ 2p1/2 appear at 856.39 and 873.72 eV, and Ni3+ 2p3/2 and Ni3+ 2p1/2 appear at 858.30 and 875.58 eV, respectively, indicating the presence of the mixed valence states of nickel species. The N 1s (Figure 3e) and O 1s (Figure 3f) peaks of GDY–NiTCNQ located at higher BE than those of pristine NiTCNQ further reveal the presence of electron-transfer in the GDY–NiTCNQ sample.38,39 The Raman ( Supporting Information Figure S6) and Fourier transform infrared (FTIR) ( Supporting Information Figure S7) measurements of the GDY layer were conducted. As shown in Supporting Information Figure S6, pure NiTCNQ spectra features several sharp characteristic peaks. GDY–NiTCNQ exhibits characteristic peaks corresponding to the D-band, G-band, and the vibration of conjugated diine links (2189.8 and 1926.2 cm−1), while the characteristic peaks of NiTCNQ diminished. Moreover, as shown in Supporting Information Figure S7, the FTIR shows the characteristic peak corresponding to GDY, as compared with that of pure NiTCNQ. These results demonstrated the successful growth of GDY on the surface of NiTCNQ. Figure 3 | Structural characterization of GDY–NiTCNQ. (a) XRD spectra of NiTCNQ and GDY-NiTCNQ. XPS spectra for GDY–NiTCNQ and NiTCNQ of (b and c) C 1s, (d) Ni 2p, (e) N 1s, and (f) O 1s. The inset figure in (b) represents the deformation charge density of NiTCNQ. (g) The normalized Co K-edge XANES spectra and (h) the first derivative XANES of GDY–NiTCNQ along with the references. (i) EXAFS spectra of GDY–NiTCNQ at the Co K-edge. Download figure Download PowerPoint Ni K-edge X-ray absorption near-edge structure (XANES) for the samples was performed. Figure 3g shows that the GDY–NiTCNQ exhibits the higher edge energy position than those of NiCl2 and NiO, suggesting the average valence state of nickel in GDY–NiTCNQ is larger than Ni2+. This also implies the mixed valence state of nickel in GDY–NiTCNQ (Figure 3h). The Fourier transforms of the Ni K-edge EXAFS spectrum of GDY–NiTCNQ exhibited a dominant peak at 1.6 Å, which could be assigned to the nearest shell coordination of the Ni–N bond (Figure 3i). The weak peak at 2.5 Å might be attributed to the aggregation of a small number of nickel atoms. The fitted Ni–N coordination number for GDY–NiTCNQ was 4.9 with an average Ni–N bond distance of 2.05 Å ( Supporting Information Table S2), smaller than that of hexa-coordinated NiTCNQ,40 which might be ascribed to the strong interactions between the GDY and NiTCNQ species. The obviously enhanced CT ability at the double layer interfaces of GDY/TCNQ/Ni was expected to endow the catalyst with incomplete CT and the infinite distribution of active sites originating from highly asymmetric surface charge distribution. The significantly increased number of active sites would further accelerate CT and lower energy barriers of the reaction. These are all beneficial to improve the catalytic activity of the catalysts. The OER catalytic performances of the samples were studied using a three-electrode system by testing LSV in O2-saturated 1.0 M KOH solution at the scan rate of 2 mV s−1. All polarization curves were corrected by the iR-compensation. NiTCNQ, NF, and RuO2 were also tested in the same conditions for reference. As shown in Figure 4a, the anodic peak appearing in the range of 1.3–1.4 V versus RHE referred to the nickel oxidation from Ni(II) to Ni(III), and the following peak represented the OER catalytic activity. GDY–NiTCNQ showed the best OER activity with the smallest overpotential of 218 mV at 10 mA cm−2 compared with pure NiTCNQ (343 mV) and commercial RuO2 (282 mV). Moreover, GDY–NiTCNQ exhibited a lower of mV than NiTCNQ mV NF mV and RuO2 mV indicating it the reaction kinetics for OER evolution (Figure For further of the OER activity, the frequency was At the overpotential of GDY–NiTCNQ a higher of s−1 than NiTCNQ NF and of the electrocatalysts ( Supporting Information Table Figure | OER and HER (a) curves of NiTCNQ, NF and RuO2 for OER at the scan rate of 2 mV s−1. (b) of the samples for curves of GDY–NiTCNQ obtained before and after OER (d) O 1s XPS spectra of GDY–NiTCNQ after OER (e) Ni 2p XPS spectra and (f) the of Ni2+ of GDY–NiTCNQ obtained after OER (g) curves of NiTCNQ, NF, and for HER at the scan rate of 2 mV s−1. (h) of the materials for HER. (i) curves of GDY–NiTCNQ obtained before and after HER O 1s XPS Ni 2p XPS and the of Ni2+ in GDY–NiTCNQ samples. Download figure Download PowerPoint stability of the catalyst is of great significance for As shown in Supporting Information Figure GDY–NiTCNQ maintained its catalytic activity for h under at mA revealing its long-term stability ( Supporting Information Figure GDY–NiTCNQ also a in catalytic activity during the tests for (Figure The of the GDY–NiTCNQ catalysts after the stability characterized by SEM ( Supporting Information Figure and TEM ( Supporting Information Figure showed no and the nanorod morphology was well the high stability of the as-prepared catalysts. situ XPS tests were on GDY–NiTCNQ to the structural evolution during the The O 1s XPS spectra showed two new peaks at and eV lattice oxygen in metal after the tests (Figure was also found that the position of the Ni 2p peak shifted to lower BE and the of the Ni2+ increased gradually during the catalysis (Figures and the of Ni2+ at these results confirm the generation of the was with the of Ni2+ in OER which a key role in the oxygen The HER catalytic activity of GDY–NiTCNQ was further tested in 1.0 M KOH solution. Figure shows the LSV curves of GDY–NiTCNQ exhibited a small overpotential of 61 mV at 10 mA which was smaller than NiTCNQ mV) and NF and to the catalyst mV). The corresponding of GDY–NiTCNQ, NiTCNQ, NF, and were and mV (Figure The for GDY–NiTCNQ, NiTCNQ, and NF were and respectively, at the overpotential of 100 All results the obvious of HER activity. Moreover, there was a in current density after indicating the high stability (Figure The of the GDY–NiTCNQ catalysts after the HER tests ( Supporting Information Figure for Supporting Information Figure for were well the high stability of the as-prepared catalysts. To reveal the of the catalytic activity, the in situ XPS measurements were conducted. As shown in Figure new peaks corresponding to the were observed at eV in the O 1s XPS spectra as compared with the as-prepared catalysts. The of Ni2+ decreased as the HER (Figures and the of state of nickel which might be the of of HER activity. For the further of the activity of GDY–NiTCNQ, were to the CT The parameters obtained were fitted with solution CT and absorption to the (Figure GDY–NiTCNQ exhibited the of and compared with NiTCNQ = = and NF = = which the conductivity and transfer process. The electrochemical active surface area was also through layer under various scan of (Figure and Supporting Information Figure GDY–NiTCNQ showed a larger of cm−2 than NiTCNQ and NF indicating the larger surface area and higher surface assigned to the introduction of GDY. on OER and HER performance, GDY–NiTCNQ was used as and in a for OWS. The catalytic system exhibited high with a low cell voltage of 1.40 V to 10 mA lower compared with those V) (Figure and the catalysts, including [email protected] V at 10 mA [email V at 10 mA V at 10 mA and so on (Figure and Supporting Information Table S4). During the of H2 and were from the and (Figure The catalytic in in basic demonstrates the promising in applications of GDY–NiTCNQ. Figure | Electrochemical properties and performance. (a) of samples in 1.0 M KOH solution. for and the fitting is (b) The at V of scan for samples. of the (d) activities of GDY–NiTCNQ and electrocatalysts. (e) The water in a working Download figure Download PowerPoint We report an in situ assembly growth method that controls the growth of NiTCNQ on the surface of GDY, to the formation of a unique D–A–D (GDY/TCNQ/Ni) structure with multiple CT. In such catalytic systems, the amount of CT between and acceptor is that incomplete CT between and surface charge distribution the number of active sites and intrinsic activity of the catalytic system, a new for the activity of the catalytic system through incomplete CT between the The results show that the by incomplete CT demonstrates excellent electrical conductivity and typical semiconductor characteristics, to the high catalytic activity of such a catalytic system in OER, HER, and OWS. We found that an electrolytic cell consisting of the CT salt as a catalyst provided a 1.40 V ultra-small cell voltage up to 10 mA is that the outer GDY film effectively prevented the corrosion of the which is to its long-term stability. This work provides a new way to selectively novel catalysts with high selectivity, activity, and stability. Supporting Information Supporting Information is the for the of Figure and Table of is no of interest to Information This research was by a from the and of the Science of and and the of the Chinese Academy of

Strain effect of PtCu alloy aerogel nanocatalysts on the oxygen reduction reaction enhancement

Ultrathin edge-rich structure of Co3O4 enabling the low charging overpotential of Li-O2 battery

Edge-enriched Ni-N4 atomic sites embedded enoki-mushroom-like carbon nanotubes assembling hollow fibers for CO2 conversion and flexible Zn-air battery

Transition metal nitrides (TMNs), by virtue of their unique electronic structure, high electrical conductivity, superior chemical stability, and excellent mechanical robustness, have triggered tremendous research interest over the past decade, and showed great potential for electrochemical energy conversion and storage. However, bulk TMNs usually suffer from limited numbers of active sites and sluggish ionic kinetics, and eventually ordinary electrochemical performance. Designing nanostructured TMNs with tailored morphology and good dispersity has proved an effective strategy to address these issues, which provides a larger specific surface area, more abundant active sites, and shorter ion and mass transport distances over the bulk counterparts. Herein, the most up-to-date progress on TMN-based nanomaterials is comprehensively reviewed, focusing on geometric-structure design, electronic-structure engineering, and applications in electrochemical energy conversion and storage, including electrocatalysis, supercapacitors, and rechargeable batteries. Finally, we outline the future challenges of TMN-based nanomaterials and their possible research directions beyond electrochemical energy applications.

Stabilizing Solid Electrolyte-Anode Interface in Li-Metal Batteries by Boron Nitride-Based Nanocomposite Coating

Bioelectrochemical systems (BES), including microbial electrosynthesis (MES), represent a sustainable route for carbon recycling through CO2 electroreduction driven by electroactive microorganisms. However, their performance is often limited by sluggish cathodic reactions and the high cost of efficient electrodes. Nitrogen-rich biochar obtained from biomass provides a low-cost, conductive, and porous matrix with abundant active sites, making it suitable for enhancing electron transfer and catalytic activity. In this study, two biomass precursors with distinct nitrogen contents-hazelnut shells (HZS, low N) and urban green waste (UGW, high N)-were screened for biochar electrode production. Physicochemical and electrochemical analyses identified UGW as the most promising feedstock. The pyrolysis and activation processes were optimized by tuning temperature, residence time, and activation strategies (KOH and CO2 flow) to maximize nitrogen retention up to 2.90wt% and porosity in the 450-613 m2g-1 range. The resulting UGW-derived biochar exhibited partially graphitized, nitrogen-enriched structures with high activity for oxygen reduction reaction (ORR), hydrogen evolution reaction (HER), and CO2 electroreduction under near-neutral conditions. When used as cathodes in MES cells, these materials promoted enhanced CO2 fixation and supported microbial communities dominated by Clostridiaceae and Eubacteriaceae, achieving average current densities of around 0.20mA cm-2 over 21-day chronoamperometric tests, consistently higher than those of the biochar-free control. These results highlight UGW-derived nitrogen-rich biochars as sustainable cathode materials enabling efficient CO2 electroreduction and MES for circular carbon utilization.

In porous form, ion conductors are key components for a vast number of applications, making detailed understanding of the impact of high surface area on electrochemical properties indispensable. Here, we report on the electrical characterization of dense and porous yttria-stabilized zirconia (YSZ) thin films deposited by pulsed laser deposition. While dense films exhibit high and dominant ionic conductivity over a wide oxygen partial pressure range, as expected for YSZ, porous films reveal an unexpectedly high electronic partial conductivity, which determines the transport properties under highly reducing conditions. By means of continuum simulations, we demonstrate that the high electronic conductivity contribution may be explained in terms of a space-charge region at the free surface, where electrons accumulate due to the positive surface charge. The latter results in increased electronic conductivity in the space-charge region, which dominates the transport properties of the porous thin films under highly reducing conditions. The results emphasize the importance of considering surface effects in nanostructured ion conductors for tailoring the overall electrochemical properties for device applications.

Although Ni‐based catalysts have been regarded as promising Pt‐free catalysts for alkaline hydrogen oxidation reaction (HOR), the competitive adsorption of H species and O‐containing species on Ni active sites significantly hinders its practical application. Metal‐organic frameworks (MOF) have emerged as highly favorable precursors for electrocatalyst synthesis due to their large specific surface area and abundant accessible active sites. Herein, a Ni‐SmO x /C catalyst is constructed by the incorporation of f‐block rare earth element (Sm) into Ni‐based MOF derivative, demonstrating its remarkable alkaline HOR behaviors on account of the well‐balanced competitive behaviors of diverse reaction intermediates on abundant active sites, induced by the interfacial charge redistribution and microenvironment modulation. Combining experimental and theoretical analyses, it can be concluded that the built‐in electric field and d‐f orbital coupling between Ni and SmO x in Ni‐SmO x /C can optimize electronic structure and induce interfacial charge redistribution, which in turn fine‐tunes and well‐balances the reaction intermediate behaviors. More critically, it can be inferred that oxophilic SmO x species serve as additional active sites for OH species with enhanced binding strength and create a local OH‐enriched microenvironment, thereby mitigating the competitive adsorption behaviors on Ni sites and ensuring an efficient supply of diverse reactive species for HOR.

Transition metal-based catalysts are commonly used for water electrolysis and cost-effective hydrogen fuel production due to their exceptional electrochemical performance, particularly in enhancing the efficiency of the oxygen evolution reaction (OER) at the anode. In this study, a novel approach was developed for the preparation of catalysts with abundant active sites and defects. The MoCoFe-phosphide catalyst nanosheets were synthesized using a simple one-step hydrothermal reaction and chemical vapor deposition-based phosphorization. The resulting MoCoFe-phosphide catalyst nanosheets displayed excellent electrical conductivity and a high number of electrochemically active sites, leading to high electrocatalytic activities and efficient kinetics for the OER. The MoCoFe-phosphide catalyst nanosheets demonstrated remarkable catalytic activity, achieving a low overpotential of only 250 mV to achieve the OER at a current density of 10 mA cm-2. The catalyst also exhibited a low Tafel slope of 43.38 mV dec-1 and maintained high stability for OER in alkaline media, surpassing the performance of most other transition metal-based electrocatalysts. The outstanding OER performance can be attributed to the effects of Mo and Fe, which modulate the electronic properties and structures of CoP. The results showed a surface with abundant defects and active sites with a higher proportion of Co2+ active sites, a larger specific surface area, and improved interfacial charge transfer. X-ray photoelectron spectroscopy (XPS) analysis revealed that the catalyst's high activity originates from the presence of Mo6+/Mo4+ and Co2+/Co3+ redox couples, as well as the formation of active metal (oxy)hydroxide species on its surface.