Abstract
A situation in which an image is combined with multiple images to form interferometric pairs is often observed in small baseline subset-interferometric synthetic aperture radar (SBAS-InSAR) deformation inversion, and this situation leads to a near linear correlation between the column vectors of the model design matrix. The Liu-type estimator introduces the parameters <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$k$ </tex-math></inline-formula> and <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$d$ </tex-math></inline-formula> into the normal equation to reduce the condition number of the design matrix and to improve the fitting properties. As the parameter <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$k$ </tex-math></inline-formula> is mainly used to reduce ill-posed problems of the design matrix, the value of <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$k$ </tex-math></inline-formula> is not limited. However, the value of <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$k$ </tex-math></inline-formula> , as determined by existing methods, is usually too large or too small. Since the calculation of the mean square error involves true values, the parameter <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$d$ </tex-math></inline-formula> is often affected by errors in the estimation results, which leads to the decreased accuracy of Liu-type estimation results. To determine the optimal value of <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$d$ </tex-math></inline-formula> , an iterative Liu-type estimator is proposed to eliminate errors. Then, the <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$L$ </tex-math></inline-formula> -curve optimization method and iterative Liu-type estimator are combined to achieve the optimal <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$k$ </tex-math></inline-formula> . The reliability and accuracy of the methods are analyzed through SBAS-InSAR deformation experiments. The experimental results show that after using the <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$L$ </tex-math></inline-formula> -curve method and an iterative operation to optimize <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$k$ </tex-math></inline-formula> and <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$d$ </tex-math></inline-formula> , the accuracy of the Liu-type estimator based on parameter optimization is clearly improved compared with that of the ridge estimator and the Liu-type estimator.
Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have