Abstract
Si passivated emitter rear contact (PERC) are expected to become the dominant cell technology in the near future [1]. In PERC cells, a thin layer of Al2O3 is deposited on the rear of the Si cell to reduce rear surface recombination on p-type Si by chemical and field-effect passivation [2]. Optically the Al2O3 film is supported by a thicker SiNx layer stacked on Al2O3, and the low refractive index of SiNx improves light trapping in the Si cell by rear reflection [3]. In commercial production, the Al2O3 film is prepared by atomic layer deposition (ALD). ALD is a slow process and the precursor for Al2O3, Al2(CH3)6, is expansive and pyrophoric. For these reasons the thickness of the Al2O3 film in PERC cells is limited to ~10 nm and the 80-nm SiNx layer is deposited on Al2O3 by plasma-enhanced chemical vapor deposition (PECVD). It is noted that the refractive index of Al2O3 is lower than that of SiNx, 1.6 vs. 2.0 [4,5], so a thicker Al2O3 film on the rear of the PERC cell should provide better rear passivation and optical trapping than an Al2O3/SiNx stack. This requires a low-cost process to deposit thicker Al2O3 on Si. In this talk, we report the suitability of spray-deposited Al2O3 for rear passivation and optical trapping in Si PERC cells. Electrical, optical and structural properties of spray-deposited Al2O3 are investigated and compared to the industrial standard ALD Al2O3/PECVD SiNx stack. It was found that spray-deposited Al2O3 has a negative charge density of 3.19×1012 cm–2 for an 80-nm film, indicating that spray-deposited Al2O3 can serve as the passivation layer. Optical properties of spray-deposited Al2O3 are identical to the ALD Al2O3/PECVD SiNx stack, suggesting that spray-deposited Al2O3 can also serve as the optical trapping layer. It was also found that spray-deposited Al2O3 is crack and pore free, and its surface roughness has a root-mean-square value of 0.42 nm for an 80-nm film. Spray-deposited Al2O3 is amorphous and its composition is slightly Al rich. The resistivity and breakdown field of 80-nm spray-deposited Al2O3 are ~1014 Ω-cm and 3.28 MV/cm, respectively. These properties suggest that spray-deposited Al2O3 is a promising candidate to replace the ALD Al2O3/PECVD SiNx stack in Si PERC cells. [1] C. Roselund, International Technology Roadmap for Photovoltaic (ITRPV), 7, 21, (2016). [2] N. Batra, J. Gope, R. Singh, J. Panigrahi, S. Tyagi, P. Pathi, S. K. Srivastava, C. M. S. Rauthan, P. K. Singh, Phys. Chem. Chem. Phys., 16(39), 21804 (2014). [3] B. Vermang, H. Goverde, L. Tous, A. Lorenz, P. Choulat, J. Horzel, J. John, J. Poortmans, R. Mertens, Prog. Photovolt. Res. Appl., 20(3), 269 (2012). [4] M. D. Groner, F. H. Fabreguette, J. W. Elam, and S. M. George, Chem. Mater., 16(4), 639 (2004). [5] J. Schmidt and M. Kerr, Sol. Energy Mater. Sol. Cells, 65(1-4), 585 (2001).
Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.