Abstract
Mining and related activities cause severe degradation of ambient air quality. A study of particulate matter (PM) across transportation, mining and control (C) sites for dust attenuation capacity (DAC) in selected tree species were carried out in Jharia coalfield (JCF) to estimate the menace of dust pollution and also to measure air pollution tolerance index (APTI). Results indicated that the maximum value of PM10 and PM2.5 ranged from 54 to 174 and 29 to 78 μg m− 3 respectively across all the sites. The maximum values occurred in transportation and the minimum at C for both the particulates. Mining and transportation resulted in an increase in PM10 values by 161 and 200% and PM2.5 values by 100 and 136% respectively as compared to those in C. The mean concentration of PM10 and PM2.5 across the sites exceeded the permissible limit of 100 and 60 μg m− 3 respectively. Transportation was worse than mining due to the high proportion of hazardous fine (PM2.5) particulates. DAC indicated that Tectona grandis (TG) captured maximum dust (2.15 mg cm− 2) with 85% and Peltophorum inerme (PI) the minimum (0.15 mg cm− 2) with 5% efficiency. The trend for DAC showed TG > Ficus glomerata (FG) > Psidium guajava (PG) > Ficus benghalensis (FB) > Ficus religiosa (FR) > Alstonia scholaris (AS) > Aegle marmelos (AM) > Gmelina arborea (GA) > Dalbergia sissoo (DS) > Syzyzium cumini (SC) > Azadirachta indica (AI) > Terminalia arjuna (TA) > Mangifera indica (MI) > Albizia lebbeck (AL) > PI in descending order. APTI based on pH, total chlorophyll, ascorbic acid and relative water content indicated maximum values for TG (17) with 90% and minimum for PI (10) with 57% of the total and is a measure of the sustainability of plants in JCF. The descending order for APTI was TG > PG > FG > FR > FB > AI > MI > SC > DS > GA > AM > AS > AL > TA > PI. Thus, TG is the most suitable and PI the least. Stomatal density is negatively related to DAC and positively related to APTI. DAC therefore, cannot be attributed to a single factor but a mix of complex factors such as morphological and anatomical characteristics of the leaf, particle size, species type, metabolism, location, meteorology and stress conditions. Based on the findings a greenbelt design was proposed to improve the air quality of the mining and transportation areas.
Highlights
India is the world’s fastest-growing economy with a population of 1.3 billion and is the fourth-largest producer of coal
The maximum values occurred in Barwa Road (BR) and the minimum was at C for both the particulates
Mining and transportation resulted in an increase in particulate matter of < 10 μ (PM10) values by 161 and 200% and PM2.5 values by 100 and 136%, respectively, as compared to those in C
Summary
India is the world’s fastest-growing economy with a population of 1.3 billion and is the fourth-largest producer of coal. Coal mining was considered one of the most polluting. The coal-burning releases harmful gases as well as particulate matter and its transportation with mine wastes. Singh et al Sustainable Environment Research (2019) 29:37 has been recognized as the prime source of suspended particulate matter (SPM) with the dominance of < 10 μ size. Hazardous level of air pollution has been found in coal-burning areas. Coal mining affects the local, regional and global environment through the release of coalbed methane, which is twenty-three times as powerful as carbon dioxide as a greenhouse gas [1]. Coal mining badly impacts air quality and is one of the most potent sources of multi-faceted environmental pollution, requires efficient mine planning, design and an effective scientific environmental management with the mine closure plan. The best practice will always set the limits on the procedure to be followed keeping cost-benefit in mind
Sign-in/Register to view highlights & summary Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Schedule a callDisclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.
