Abstract
Site amplification factors in National Building Codes are typically specified as a function of the average shear wave velocity over the first 30 m (Vs30) or site class (A, B, C, D and E) for defined ranges of Vs30 and/or ranges of depth to bedrock. However, a single set of amplification factors may not be representative of site conditions across the country, introducing a bias in seismic hazard and seismic risk analyses. This is exemplified by significant differences in geological settings between East and West coast locations in North America. Western sites are typically characterized by lower impedance contrasts between recent surface deposits and bedrock in comparison to Eastern sites. In North America, site amplification factors have been derived from a combination of field data on ground motions recorded during West Coast earthquakes and numerical models of site responses that are meant to be representative of a wide variety of soil profiles and ground motions. The bias on amplifications and their impact on seismic hazards is investigated for the Montreal area, which ranks second for seismic risks in Canada in terms of population and hazard (PGA of 0.25 g for a 2475 years return period). Representative soil profiles at several locations in Montreal are analyzed with 1-D site response models for natural and synthetic ground motions scaled between 0.1 to 0.5 g. Since bedrock depths are typically shallow (<30 m) across the island, bedrock shear wave velocities have a significant influence on the impedance contrast and amplifications. Bedrock shear wave velocity is usually very variable due to the differences in rock formations, level of weathering and fracturing. The level of this uncertainty is shown to be greatly decreased when rock quality designation (RQD) data, common information when bore hole data are logged, is available since it is highly correlated with both shear and compression wave velocities. The results are used to derive region-specific site amplification factors as a function of both Vs30 and site fundamental frequency and compared to those of the National Building Code of Canada (2015). The results of the study indicate that there are large uncertainties associated with these parameters due to variability in soil profiles, soil properties and input seismic ground motions. Average and confidence intervals for the mean and for predictions of amplification factors are calculated for each site class to quantify this uncertainty. Amplifications normalized relative to class C are obtained by accounting for the correlation between site class amplifications for given ground motions. Non-linearity in the analysis of equivalent linear 1-D site response is taken into account by introducing the non-linear G/Gmax and damping ratios curves. In this method, it is assumed that the shear strain compatible shear modulus and damping ratio values remains constant throughout the duration of the seismic excitation. This assumption is not fully applicable to a case when loose saturated soil profile undergo heavy shaking (PGA > 0.3 g). In this study, all simulations with input motion PGA >0.3 g have been performed by using the EL method instead of the NL method considering that cohesive soils (clay and silt) at Montreal sites are stiff and cohesionless soils (sand and gravel) are considerably dense. In addition, the field and laboratory data required to perform NL analyses are not currently available and may be investigated in future works.
Highlights
The region of Montreal, Canada, is the second city at risk in Canada for its population and seismic hazard [1]
Results are shown for a rock quality designation (RQD) of 5 since the rock velocities for this category is 2900 m/s, which is similar to the velocity assumed in the Central and Eastern North America (CENA) study (3000 m/s)
CENA results are slightly smaller than those obtained with the current study, which could be partially explained by the lower degree of damping for Leda clay and differences in shear wave velocity profiles in the CENA site profiles (Figure 4)
Summary
The region of Montreal, Canada, is the second city at risk in Canada for its population and seismic hazard [1]. No damaging events have been recorded to provide insight on site response and structural performance. The most significant recent event in Montreal occurred in 1988 (M 5.7) in the Saguenay region, approximately 350 km NE of the city and caused structural damaged to the Montreal East city hall built on a 17 m soft clay layer that may have amplified the ground motions [2,3]. Zones with similar soft soil are found in the downtown area and along the south east shore of the island [4,5]. Given the lack of historical data, an approach based on simulation of ground motions is proposed here to investigate site effects
Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.