Abstract

Various carboxylic acid-functionalized poly(N,N-dimethylacrylamide) (PDMAC) macromolecular chain transfer agents (macro-CTAs) were chain-extended with diacetone acrylamide (DAAM) by reversible addition–fragmentation chain transfer (RAFT) aqueous dispersion polymerization at 70 °C and 20% w/w solids to produce a series of PDMAC–PDAAM diblock copolymer nano-objects via polymerization-induced self-assembly (PISA). TEM studies indicate that a PDMAC macro-CTA with a mean degree of polymerization (DP) of 68 or higher results in the formation of well-defined spherical nanoparticles with mean diameters ranging from 40 to 150 nm. In contrast, either highly anisotropic worms or polydisperse vesicles are formed when relatively short macro-CTAs (DP = 40–58) are used. A phase diagram was constructed to enable accurate targeting of pure copolymer morphologies. Dynamic light scattering (DLS) and aqueous electrophoresis studies indicated that in most cases these PDMAC–PDAAM nano-objects are surprisingly resistant to changes in either solution pH or temperature. However, PDMAC40–PDAAM99 worms do undergo partial dissociation to form a mixture of relatively short worms and spheres on adjusting the solution pH from pH 2–3 to around pH 9 at 20 °C. Moreover, a change in copolymer morphology from worms to a mixture of short worms and vesicles was observed by DLS and TEM on heating this worm dispersion to 50 °C. Postpolymerization cross-linking of concentrated aqueous dispersions of PDMAC–PDAAM spheres, worms, or vesicles was performed at ambient temperature using adipic acid dihydrazide (ADH), which reacts with the hydrophobic ketone-functionalized PDAAM chains. The formation of hydrazone groups was monitored by FT-IR spectroscopy and afforded covalently stabilized nano-objects that remained intact on exposure to methanol, which is a good solvent for both blocks. Rheological studies indicated that the cross-linked worms formed a stronger gel compared to linear precursor worms.

Highlights

  • This watersoluble homopolymer precursor was chain-extended with diacetone acrylamide (DAAM) via reversible addition−fragmentation chain transfer (RAFT) aqueous dispersion polymerization at 70 °C and 20% w/w solids

  • The linear evolution of Mn (DMF Gel Permeation Chromatography (GPC) vs PMMA standards) with conversion was accompanied by low dispersities throughout (Mw/Mn ≤ 1.12), which indicates a well-controlled RAFT polymerization.[72−74] Subsequently, a range of PDMAC macro-CTAs were prepared with mean degree of polymerizations of 40, 46 58, 68, or 77, as determined by end-group analysis using UV spectroscopy

  • Lovett et al reported that poly(glycerol monomethacrylate)−poly(2-hydroxypropyl methacrylate) (PGMA−poly(2hydroxypropyl methacrylate) (PHPMA)) diblock copolymer nano-objects prepared by RAFT aqueous dispersion polymerization using a carboxylic acid-functionalized CTA exhibit pH-responsive behavior.[63,66]

Read more

Summary

Introduction

AB diblock copolymer self-assembly has attracted considerable attention in recent decades as a convenient method for preparing organic nanoparticles with spherical, wormlike, or vesicular morphologies.[1−10] Traditionally, block copolymer selfassembly is achieved using a postpolymerization processing method such as a solvent switch.[5,7−9,11,12] this approach typically requires relatively low copolymer concentrations (

Results
Conclusion
Full Text
Published version (Free)

Talk to us

Join us for a 30 min session where you can share your feedback and ask us any queries you have

Schedule a call