Abstract
Objective: This work was aimed at formulating artesunate tablets with hydroxypropyl methylcellulose (HPMC)-a hydrophilic polymer for the purpose of achieving a sustained release profile of the drug and evaluating their properties.Methods: The solubility profile of artesunate was determined in water, methanol, ethanol, ethanol/water mixtures (50/50, 40/60 v/v), simulated intestinal fluid (SIF) without enzymes (pH 7, 7.2 and 8), simulated gastric fluid (SGF) without enzymes (pH 1.2), 0.1N hydrochloric acid (HCI), 0.1N sodium hydroxide (NaOH), 0.1N acetic acid and phosphate buffer solution, PBS (pH 7, 7.2 and 8). Four batches of oral sustained release artesunate tablets intended for once-daily dosing were formulated with 10%, 20%, 25% and 30% w/w concentrations of HPMC using wet granulation method. Evaluation of granule properties was done by determining the angle of repose, flow rate, bulk density, tapped density, Carr’s index and Hausner’s quotient. The compressed tablets were also evaluated using official and non-official parameters. Absolute drug contents were determined in 0.1N NaOH, ethanol and methanol. In vitro release was studied in different media and release kinetics mechanism elucidated. In vivo studies were carried out using healthy Wistar rats.Results: Artesunate was observed to exhibit solubility at varying degrees depending on solvents or media employed as well as the pH of the media. All the granule batches have Hausner’s quotient value of approximately 1.2. The values for Carr’s index for all the batches ranged between 30 and 40. The angle of repose, Carr’s index and Hausner’s quotient values indicate good flow properties of the granules for all the batches. All the tablet batches conformed to official standard in terms of weight uniformity as no single tablet deviated beyond 5% from the average weight in each batch with no significant difference in the values (p>0.05). Values of hardness increased insignificantly from batches A to D (p>0.05). Friability values were very low and follows no specific pattern among the batches but the difference in the values was significant (p<0.05). Absolute drug content reduced while in vitro release times increased as hardness increased, indicating the probable progressive reduction in the tendency of the matrix to release the drug as the concentration of HPMC increased from batches A to D. n values obtained from analysis of release mechanism were above 0.89 for each batch.Conclusion: The release mechanism was shown to be complex and the release involved zero order, first order, and Higuchi model kinetics. The biological half-life of artesunate was shown to be 1.05 hr, and metabolites which bear resemblance to artesunate in absorbance seem to be encountered. In this work, HPMC matrix yielded high-quality tablets indicating its usefulness in sustained released product development.
Highlights
Post-1990 is the modern era of controlled release technology-the period in which an attempt at drug delivery optimization is emphasized [1]
Cellulose ethers are often preferred polymers in film coating, hydroxypropyl methylcellulose (HPMC), these polymers have been reported to retard drug dissolution [3, 4]
Artesunate has not been analyzed against the backdrop of polymorphism and these differences in solubility may have farreaching effects on its pharmacokinetics and pharmacodynamics
Summary
Post-1990 is the modern era of controlled release technology-the period in which an attempt at drug delivery optimization is emphasized [1]. The concept of sustained release formulation was developed to eliminate the need for multiple dosage regimens, for those drugs requiring reasonably constant blood levels over a long period of time. It has been adopted for those drugs that needed to be administered in high doses but where too rapid a release is likely to cause undesirable side effects [3]. HPMC is a cellulose derivative chemically known as cellulose hydroxypropyl methyl ether It is soluble in different solvents and their mixtures [4] and is widely used in oral and topical pharmaceutical formulations. Cellulose ethers are often preferred polymers in film coating, HPMC, these polymers have been reported to retard drug dissolution [3, 4]
Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.