Abstract

We investigated the conceptual capability of Moistube irrigation (MTI) to discharge under zero applied positive pressure and under varied climatic conditions by inducing an artificial evaporative demand (Ed) or negative pressure around Moistube tubing. This study was premised on the null hypothesis that an artificially induced Ed or negative pressure does not impact MTI discharge. Moistube tubing was enclosed in a 1 m long PVC conduit. A 20 l water reservoir placed on an electronic balance provided a continuous supply of water whilst a three-speed hot air blower facilitated the radiative factor and advection process. The procedure was conducted under varied climatic conditions with three air velocity (ua) treatments namely; 1.2 m.s-1, 2.5 m.s-1, and 3.0 m.s-1 and the experiment run times were 159 h, 134 h and 10 h, respectively. The average temperature (Tave) and relative humidity (RH) data for ua = 1.2 m.s-1 were 53°C and 7.31%, whilst for ua = 2.5 m.s-1, Tave was 56°C and RH = 7.19%, and for ua = 3.0 m.s-1, Tave was 63°C and RH = 6.16%. The experimental data was input into the four variable Penman-Monteith method to compute the evaporative demand (Ed). For each Ed, the instantaneous mass flow rate ([Formula: see text]) was recorded using an electronic balance and subsequently converted to volumetric flow rates. For each of the air velocities, the respective Ed values obtained were 0.16, 0.31 and 0.36 mm.d-1. The Bowen ratios (r) were well below 1 (r < 1), which suggested a sufficient supply of moisture to evaporate. For Ed = 0.16 mm.d-1 the vapour pressure deficit (VPD) was 113.08 mbars, whilst for Ed = 0.31 mm.d-1 and for Ed = 0.36 mm.d-1 the VPD were 129.93 mbars and 150.14 mbars, respectively. The recorded discharges (q) at normalised time (t*) = 1 h for Ed = 0.16 mm.d-1 was 7.67*10-3 l.hr-1.m-1 length, whilst for Ed = 0.31 mm.d-1 q = 14.5*10-3 l.hr-1.m-1 length, and for Ed = 0.36 mm.d-1 q = 20.8*10-3 l.hr-1.m-1 length. The imposed negative pressure causes an exponential increase in Moistube™ discharge, thus disproving the null hypothesis. The higher the evaporative demand the higher the discharge. This phenomenon allows MTI to be used for deficit irrigation purposes and allows irrigators to capitalize on realistic soil matric potential irrigation scheduling approach.

Highlights

  • Moistube irrigation (MTI) is a relatively new semi-permeable membrane (SPM) irrigation technology

  • We investigated the conceptual capability of Moistube irrigation (MTI) to discharge under zero applied positive pressure and under varied climatic conditions by inducing an artificial evaporative demand (Ed) or negative pressure around Moistube tubing

  • In the absence of applied pressure, the discharge is a function of matric potential (ψ) [1,2,3].Negative pressure irrigation (NPI) is when water supply pressure is regulated by soil matric potential [4]

Read more

Summary

Introduction

Moistube irrigation (MTI) is a relatively new semi-permeable membrane (SPM) irrigation technology. The technology utilises nano-technology such that the inner membrane imitates plant water uptake, which facilitates discharge according to crop water requirements [1, 2]. MTI is a low pressure discharge sub-surface irrigation technology whose functionality is similar to ceramic pitcher pots. In the absence of applied pressure, the discharge is a function of matric potential (ψ) [1,2,3].Negative pressure irrigation (NPI) is when water supply pressure is regulated by soil matric potential [4]. NPI can be classified as a precision irrigation technique which offers benefits such as continuous regulation of soil moisture improving crop yield, reduction of non-beneficial water use such as water loss by evaporation and runoff [4,5,6]. The Ed mimics changing soil water conditions exploring MTI applicability to deficit irrigation

Methods
Results
Conclusion
Full Text
Published version (Free)

Talk to us

Join us for a 30 min session where you can share your feedback and ask us any queries you have

Schedule a call