Abstract
All-solid-state rechargeable lithium-ion batteries have attracted much interest recently for applications of much larger scale than previous thin-film batteries. The replacement of an organic liquid electrolyte with a non-flammable inorganic solid electrolyte (SE) may simplify battery design and improve safety and durability [2]. However, in all-solid cells, the battery life depends in large measure on the mechanical integrity of the composite system [1]. A suitable theory to identify the electro-chemo-mechanical limits of Li-ion batteries performance in realistic electrode-electrolyte configurations is therefore required. In this work, a fully coupled electro-chemo-mechanical model is developed to facilitate the mesoscale optimization of such composite microstructures. A key development in all-solid-state batteries has been the discovery of solid electrolytes with high Li+ ion conductivity at room temperature comparable to that of organic liquid electrolytes [3, 4, 5]. These have been tested with numerous electrode active materials.The durability of a coherent solid-solid interface between electrode and electrolyte is likely to be an important consideration. Notwithstanding the several techniques investigated to increase the contact area at the interface [6], interface cohesion and its effects on the rate capability and the overall performance throughout the expected life cycles needs to be maintained. In the present research, we develop a nonlinear continuum model able to account for the combined effects of Li diffusion and for the consequent volumetric expansion of the hosting material. The electrode and electrolyte are idealized as elastic materials with elastic properties varying with lithium concentration. The complexity and the multi-physical nature of the problem require numerical modeling strategies and pose several challenges. To address this, we have established a computational framework based on large deformation kinematics and posed in a thermodynamically consistent fashion. The model is implemented in an in-house, object oriented C++ numerical code that incorporates three-dimensional finite element calculations. The numerical analysis allows for delamination at the interface between electrode particles and solid electrolyte. Crack formation and propagation is predicted by means of a cohesive zone model extended to include decreased Li flux across interfaces due to their loss of mechanical integrity. Our simulations indicate trends of mechanical reliability of all-solid state batteries realized with some of the most promising solid electrolyte materials (e.g. Li2S-P2S5 [1], LIPON [3], garnet SE [7]), using mechanical properties available in literature. When physical values for the solid electrolyte’s mechanical behavior are not available, the simulations indicate trends of how mechanical reliability correlates with the battery design and operating conditions (i.e., charging rate). Acknowledgments The work was supported by the grant DE-SC0002633 funded by the U.S. Department of Energy, Office of Science. Keywords Lithium ion batteries, All-solid-state batteries, Nonlinear continuum mechanics; Diffusion; Thermodynamics References [1] A. Hayashi, K. Noi, A. Sakuda, and M. Tatsumisago. Superionic glass-ceramic electrolytes for room-temperature rechargeable sodium batteries. Nature Communications, 3, 2012. [2] K. Takada. Progress and prospective of solid-state lithium batteries. Acta Materialia, 61(3):759 – 770, 2013. [3] J.B Bates, N.J. Dudney, B. Neudecker, A. Ueda, and C.D. Evans. Thin-film lithium and lithium-ion batteries. Solid State Ionics, 135(1 - 4):33 – 45, 2000. [4] Y. Seino, T. Ota, K. Takada, A. Hayashi, and M. Tatsumisago. A sulphide lithium super ion conductor is superior to liquid ion conductors for use in rechargeable batteries. Energy Environ. Sci., 7:627–631, 2014. [5] N. Kamaya, K. Homma, Y. Yamakawa, M. Hirayama, R. Kanno, M. Yonemura, T. Kamiyama, Y. Kato, S. Hama, K. Kawamoto, and A. Mitsui. A lithium superionic conductor. Nature materials, 10(9):682–6, September 2011. [6] M. Tatsumisago, M. Nagao, and A. Hayashi. Recent development of sulfide solid electrolytes and interfacial modification for all-solid-state rechargeable lithium batteries. Journal of Asian Ceramic Societies, 1(1):17 – 25, 2013. [7] E. Rangasamy, J. Wolfenstine, and J. Sakamoto. The role of Al and Li concentration on the formation of cubic garnet solid electrolyte of nominal composition Li7La3Zr2O12. Solid State Ionics, 206(0):28 – 32, 2012. Figure 1: Simulation of a composite all-solid Li-ion battery microstructure upon lithiation. The diffusion fronts (white lines) appear perturbed due to partial delamination of the interface between electrode particles and solid electrolyte. Figure 1
Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have