Abstract

BackgroundThe unique physicochemical properties of multi-walled carbon nanotubes (MWCNT) have led to many industrial applications. Due to their low density and small size, MWCNT are easily aerosolized in the workplace making respiratory exposures likely in workers. The International Agency for Research on Cancer designated the pristine Mitsui-7 MWCNT (MWCNT-7) as a Group 2B carcinogen, but there was insufficient data to classify all other MWCNT. Previously, MWCNT exposed to high temperature (MWCNT-HT) or synthesized with nitrogen (MWCNT-ND) have been found to elicit attenuated toxicity; however, their genotoxic and carcinogenic potential are not known. Our aim was to measure the genotoxicity of MWCNT-7 compared to these two physicochemically-altered MWCNTs in human lung epithelial cells (BEAS-2B & SAEC).ResultsDose-dependent partitioning of individual nanotubes in the cell nuclei was observed for each MWCNT material and was greatest for MWCNT-7. Exposure to each MWCNT led to significantly increased mitotic aberrations with multi- and monopolar spindle morphologies and fragmented centrosomes. Quantitative analysis of the spindle pole demonstrated significantly increased centrosome fragmentation from 0.024–2.4 μg/mL of each MWCNT. Significant aneuploidy was measured in a dose-response from each MWCNT-7, HT, and ND; the highest dose of 24 μg/mL produced 67, 61, and 55%, respectively. Chromosome analysis demonstrated significantly increased centromere fragmentation and translocations from each MWCNT at each dose. Following 24 h of exposure to MWCNT-7, ND and/or HT in BEAS-2B a significant arrest in the G1/S phase in the cell cycle occurred, whereas the MWCNT-ND also induced a G2 arrest. Primary SAEC exposed for 24 h to each MWCNT elicited a significantly greater arrest in the G1 and G2 phases. However, SAEC arrested in the G1/S phase after 72 h of exposure. Lastly, a significant increase in clonal growth was observed one month after exposure to 0.024 μg/mL MWCNT-HT & ND.ConclusionsAlthough MWCNT-HT & ND cause a lower incidence of genotoxicity, all three MWCNTs cause the same type of mitotic and chromosomal disruptions. Chromosomal fragmentation and translocations have not been observed with other nanomaterials. Because in vitro genotoxicity is correlated with in vivo genotoxic response, these studies in primary human lung cells may predict the genotoxic potency in exposed human populations.

Highlights

  • The unique physicochemical properties of multi-walled carbon nanotubes (MWCNT) have led to many industrial applications

  • Characterization Length and diameter High-resolution scanning transmission electron microscopy (STEM) images showed a tubular structure with multiple walls for each MWCNT material (Fig. 1a-f)

  • High-resolution STEM imaging identified residual catalyst material within the MWCNT-ND structure that was identified as iron through energy dispersive X-ray spectroscopy (EDS; Fig. 1g&h)

Read more

Summary

Introduction

The unique physicochemical properties of multi-walled carbon nanotubes (MWCNT) have led to many industrial applications Due to their low density and small size, MWCNT are aerosolized in the workplace making respiratory exposures likely in workers. Multi-walled carbon nanotubes (MWCNT) have been used and studied extensively given their unique physicochemical properties such as high aspect ratio, rigidity, strength, and electrical conductance [1] They are widely used for industrial applications leading to potential occupational exposures. The International Agency for Research on Cancer (IARC) designated the Mitsui-7 MWCNT (MWCNT7), an extensively-studied pristine MWCNT material, as a Group 2B carcinogen or “possibly carcinogenic to humans” citing multiple studies that indicate tumor growth in rodents and genotoxicity relevant to humans [3]. An investigation of the genotoxic mechanisms of MWCNT-7 and physicochemically-altered MWCNT materials is needed in models relevant to human occupational exposure

Objectives
Methods
Results
Conclusion
Full Text
Published version (Free)

Talk to us

Join us for a 30 min session where you can share your feedback and ask us any queries you have

Schedule a call