Micro-Mechanical Fracture Investigations on Grain Size Tailored Tungsten-Copper Nanocomposites

Abstract

Tungsten-copper composites are used in harsh environments because of their superior material properties. This work addresses a tungsten-copper composite made of 20 wt.% copper, which was subjected to grain refinement by high-pressure torsion, whereby the deformation temperature was varied between room temperature and 400 °C to tailor the grain size. Deformation was performed up to microstructural saturation and verified by hardness measurement and scanning electron microscopy. From the refined nanostructured material, micro-cantilever bending beams with cross-sections spanning from 5 × 5 to 35 × 35 µm2 were cut to examine possible size effects and the grain size influence on the fracture behavior. Fracture experiments were performed in situ inside a scanning electron microscope by applying a quasi-static loading protocol with partial unloading steps. Inspection of the fracture surfaces showed that all cantilevers failed in an inter-crystalline fashion. Nevertheless, remaining coarser tungsten grains impacted the resultant fracture toughness and morphology. Cantilevers fabricated from the 400 °C specimen exhibited a fracture toughness of 220 ±\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\pm $$\\end{document} 50 Jm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\frac{{\ ext{J}}}{{{\ ext{m}}}^{2}}$$\\end{document}. For the room temperature cantilevers, a fracture toughness of 410 ±\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\pm $$\\end{document} 50 Jm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\frac{{\ ext{J}}}{{{\ ext{m}}}^{2}}$$\\end{document} was observed, which declined to 340 ±\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\pm $$\\end{document} 30 Jm2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\frac{{\ ext{J}}}{{{\ ext{m}}}^{2}}$$\\end{document} for cantilevers < 10 × 10 µm2, confirming a size effect. The increased fracture toughness is attributed to the delamination-like structures formed in the room temperature sample.