Abstract

Twin-I girder bridge systems composite with precast concrete deck have advantages including construction simplification and improved concrete strength compared with traditional multi-I girder bridge systems with cast-in-place concrete deck. But the cracking is still a big issue at interior support for continuous span bridges using twin-I girders. To reduce cracks occurrence in the hogging regions subject to negative moments and to guarantee the durability of bridges, the most essential way is to reduce the tensile stress of concrete deck within the hogging regions. In this paper, the prestressed tendons are arranged to prestress the precast concrete deck before it is connected with the steel girders. In this way, the initial compressive stress induced by the prestressed tendons in the concrete deck within the hogging region is much higher than that in regular concrete deck without prestressed tendons. A finite element analysis is developed to study the long-term behaviour of prestressed concrete deck for a twin-I girder bridge. The results show that the prestressed tendons induce large compressive stresses in the concrete deck but the compressive stresses are reduced due to concrete creep. The final compressive stresses in the concrete deck are about half of the initial compressive stresses. Additionally, parametric study is conducted to find the effect to the long-term behaviour of concrete deck including girder depth, deck size, prestressing stress and additional imposed load. The results show that the prestressing compressive stress in precast concrete deck is transferred to steel girders due to concrete creep. The prestressed forces transfer between the concrete deck and steel girder cause the loss of compressive stresses in precast concrete deck. The prestressed tendons can introduce some compressive stress in the concrete deck to overcome the tensile stress induced by the live load but the force transfer due to concrete creep needs be considered. The concrete creep makes the compressive stress loss and the force redistribution in the hogging regions, which should be considered in the design the twin-I girder bridge composite with prestressed precast concrete deck.

Highlights

  • A two or multiple-I girder system has two or more steel I girders connected with diaphragms and composite with a concrete deck using shear studs

  • While within the regions of negative moments, the concrete deck is in tension under vertical loads and the tensile stress may increase due to concrete shrinkage and creep

  • The results show that the concrete creep reduces the initial compressive stress in the concrete deck and causes force transfer between the concrete deck and the steel girders

Read more

Summary

Introduction

A two or multiple-I girder system has two or more steel I girders connected with diaphragms and composite with a concrete deck using shear studs. Liu et al analysed the jacking-up method to prestress the concrete deck and they found that jacking-up the interior support could efficiently introduce compressive stress in the concrete deck in the hogging regions to overcome the tensile stresses induced by shrinkage and live load [13]. Either prestressed tendons or construction strategies can introduce initial compressive stress in the concrete deck to avoid or reduce concrete cracking in the hogging regions. The way to arrange prestressed tendons in concrete deck in the hogging regions is used for twin-I girders with post connected prestressed precast concrete deck. The long-term behaviour of a continuous twin-I girder bridge is investigated to find the creep effect on the compressive stresses induced by the prestressed tendons. Parametric study is developed to find the creep effect on the prestressing the concrete deck and the force transfer between steel girders and concrete deck

Case of a Twin-I Girder Composite with Precast Deck
Igirder
Finite
Material Models
(Method
= 1 (Method which is denoted follows:
Method
Prestressed Concrete Deck Condition
Parametric Studies
Girder
Stress at the flange of thechange steel girders the hogging region after
Girder Depth
Deck Thickness
Prestressing Stress
Additional
Findings
Conclusions
Full Text
Paper version not known

Talk to us

Join us for a 30 min session where you can share your feedback and ask us any queries you have

Schedule a call

Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.