Abstract

Simple SummaryOver the past thirty years, the thermal modification of wood has become a universally recognised and commercialised wood modification process. Thermal modifications may affect wood properties, either positively (dimensional stability and decay resistance) or negatively (mechanical properties). The combination of the impregnation of specific reagents with thermal modification may help to overcome the negative effects on wood properties. In this study, we evaluate the effect of a combination of two zwitterionic buffers, bicine and tricine, and thermal modification of two wood species (beech and spruce) against subterranean termites and their symbiotic fauna. Bicine and tricine treatments alone had a clear influence on wood mass loss and termite survival. The flagellate protist symbiotic community was affected by the treatments and responded differently to them, as a highly adaptable community. However, the combination of bicine with the thermal modification showed a negative effect on termites and their symbionts on both wood species. The combination of these different factors should be further investigated, as these results seem to be promising with regard to the enhancement of the termite resistance of wood.The majority of thermal modification processes are at temperatures greater than 180 °C, resulting in a product with some properties enhanced and some diminished (e.g., mechanical properties). However, the durability of thermally modified wood to termite attack is recognised as low. Recent attempts at combining thermal modification with chemical modification, either prior to or directly after the thermal process, are promising. Buffers, although not influencing the reaction systems, may interact on exposure to certain conditions, potentially acting as promoters of biological changes. In this study, two zwitterionic buffers, bicine and tricine, chosen for their potential to form Maillard-type products with fragmented hemicelluloses/volatiles, were assessed with and without thermal modification for two wood species (spruce and beech), with subsequent evaluation of their effect against subterranean termites (Reticulitermes grassei Clément) and their symbiotic protists. The effect of the wood treatments on termites and their symbionts was visible after four weeks, especially for spruce treated with tricine and bicine and heat treatment (bicine HT), and for beech treated with bicine and bicine and heat treatment (bicine HT). The chemical behaviour of these substances should be further investigated when in contact with wood and also after heat treatment. This is the first study evaluating the effect of potential Maillard reactions with zwitterionic buffers on subterranean termite symbiotic fauna.

Highlights

  • The subterranean termites are known as major pests of applied wood and their control has always been challenging, and even more so in an environmentally friendly way

  • No significant difference was identified in termite survival (F = 1.83; dF = 5; p = 0.181), despite the lower values of termite survival for termites fed with bicine and bicine and heat treatment beech (Table 1)

  • The results for wood mass loss (F = 14.40; dF = 5; p < 0.001) and termite attack grade (Table 2) corroborate the differences observed in termite survival rate, and two groups are visible: 1) untreated beech and heat-treated beech (HT), and 2) bicine and bicine and heat treatment, including tricine, which had significantly lower mass loss compared to group 1

Read more

Summary

Introduction

The subterranean termites are known as major pests of applied wood and their control has always been challenging, and even more so in an environmentally friendly way. Heat-treated wood may exhibit different degrees of resistance to termites, according to the wood product and heat treatment technique, among other factors (e.g., [2,3,4]), but is generally recognised as low [5]. The majority of thermal treatments of wood involve temperatures greater than 180 ◦C, resulting in a product with some properties enhanced (e.g., dimensional stability, durability, aesthetical colour) and some diminished (e.g., mechanical properties). The loss of mechanical strength has been a limitation to the use of conventional thermally modified wood in certain products. The mechanical strength reduction is linked in varying degrees to the release of acidic volatile species, the acid-catalysed depolymerisation of the hemicelluloses present, and the plasticisation and redistribution of the lignin components present

Methods
Results
Discussion
Conclusion
Full Text
Published version (Free)

Talk to us

Join us for a 30 min session where you can share your feedback and ask us any queries you have

Schedule a call