Abstract
The conducted studies revealed the influence of the methods of cupellation and the XFA on the accuracy of determining the millesimal fineness in the system of the assay control. The effect of the alloy composition of jewelry alloys on determining millesimal fineness was established. In particular, it was experimentally proved that nickel in combination with zinc as an integrated alloying component substantially changes the cupellation process of gold alloys. This leads to deviation of the millesimal fineness of a gold alloy, determined by cupellation compared with the X-ray fluorescent analysis (XFA) towards a decrease ranging from 0.10 to 0.15 %. The research of gold alloys with the content of nickel with the help of the XFA revealed microalloying by modifiers and actively acting deoxidizing agents (indium, palladium, platinum, etc.). It was established that modifiers are used both separately and in complex, but they do not make a significant impact on determining the millesimal fineness. A number of systemic and random errors in techniques, which affect the results of determining and are related to the technique of performing preparatory operations, as well as analyses operation, were detected. Based on the obtained results, the permanent temperature mode was developed and the procedure of the process of cupellation of gold alloys with the content of nickel was improved with a view to further improvement and metrological certification of the procedure. It was proved that the use of the XFA method for control of millesimal fineness and the content of the component composition of modern gold-based pieces of jewelry and museum values (antiques) is possible not only as the method of screening. The method can replace the touchstone (with obvious advantages), and be an alternative to cupellation. Application of the XFA for current control of millesimal fineness and the content of an alloy of jewelry pieces is advisable to increase up to 30 % (against 2 % in accordance with the current legislation). Its use will make it possible to increase the number of analyzed samples without worsening the trading presentation of the jewelry pieces of a customer
Highlights
The quality and value of a precious alloy is primarily determined by millesimal fineness of gold, regulated by the legislative base as the state standard and certifying the content of weight units of the main precious metal in one thousand weight units of the alloy
Analysis of the component composition of alloys based on white gold of 585 millesimal fineness, obtained by the method of X-ray fluorescence analysis (XFA), makes it possible to state that gold, silver, zinc, nickel, palladium are basic in them; impurities include indium, iron, and cadmium
It is proved that the use of the XFA method for the control of millesimal fineness and content of the component alloy of modern jewelry and museum valuables based of gold is possible as the method of screening
Summary
The quality and value of a precious alloy is primarily determined by millesimal fineness of gold, regulated by the legislative base as the state standard and certifying the content of weight units of the main precious metal in one thousand weight units of the alloy. Introduction of a new composition of alloying components and impurities causes a change in the systems of condition, mechanisms of formation of a solid solution, product manufacturing technology, structure, and properties It complicates a complex process of analysis for existence in it of the main component – gold. Despite a number of advantages related to the use of the XFA (X-ray fluorescence analysis) in determining the millesimal fineness of an alloy, its results are difficult to analyze [1] This applies to the cases when there is a coating or there are two different types of alloys (yellow and white gold; gold and silver), or the product after casting was subject to additional heat treatment (recrystallization annealing) of not high quality. The studies of determining the impact factors on determining the millesimal fineness of gold of a precious alloy by the method of cupellation and XFA, establishing the correlation between them and further improvement of the technique of assay analysis should be considered relevant
Sign-in/Register to view highlights & summary Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Schedule a callMore From: Eastern-European Journal of Enterprise Technologies
Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.
