Abstract

NOx storage-reduction (NSR) is a potential approach for the effective removal of NOx under the lean conditions in lean-burn engines. Herein, manganese-doped mixed oxides (Mn/MgAlOx) with high performance for low temperature NOx storage and release were derived from hydrotalcites precursors prepared by a facile coprecipitation method. The catalysts were characterized by X-ray diffraction (XRD), SEM, N2 adsorption-desorption, H2-TPR, FT-IR, and X-ray photoelectron spectroscopy (XPS) techniques. The Mn-doped MgAlOx catalysts exhibited high NOx storage capacity (NSC) at low temperature range (150–300 °C), which was related to their increased surface area, improved reducibility and higher surface Mn3+ content. The largest NSC measured, 426 μmol/g, was observed for NOx adsorption at 200 °C on Mn15 catalyst (the sample containing 15 wt% of Mn). The in situ DRIFTS spectra of NOx adsorption proved that the Mn-doped hydrotalcite catalysts are preferred for low temperature NOx storage and release due to their ability to store NOx mainly in the form of thermally labile nitrites. NSR cycling tests revealed the NOx removal rate of Mn15 sample can reach above 70% within the wide temperature range of 150–250 °C. Besides, the influence of CO2, soot, H2O and SO2 on NOx storage performance of Mn15 catalyst was also studied. In all, owning to their excellent NOx storage capacity, NSR cycling performance, and resistance to CO2, soot, SO2 and H2O, the Mn-doped MgAlOx NSR catalysts have broad application prospects in NOx control at low temperatures.

Highlights

  • The Lean-burn engines are gradually being promoted and applied due to their high fuel economy and low pollution emissions

  • In consideration of excellent NO oxidation activity of Mn-based oxides and potential NOx storage performance of hydrotalcites catalysts, a series of Mn-doped MgAlOx catalysts derived from hydrotalcites were prepared as alternative NOx storage and reduction (NSR) catalysts and their low-temperature performance have been studied in the present work

  • The chemical composition of the synthesized precursors, the lattice parameters, as well as mean dopant may incorporate into the Mg/Al hydrotalcite structure

Read more

Summary

Introduction

The Lean-burn engines (diesel and lean-burn gasoline engines) are gradually being promoted and applied due to their high fuel economy and low pollution emissions. Guo et al [28] systematically studied the NOx storage and release in the alternative lean-burn/rich-burn atmospheres over Mn2 O3 , Mn3 O4 and MnO2 catalysts at low temperatures (≤ 200 ◦ C) and found that Mn2 O3 showed high NO oxidizability and MnO2 had the biggest NOx storage capacity They suggested that the Mn3+ ions and surface-active oxygen species are the key to high NO oxidation activity. Similar to Pt/BaO/Al2 O3 NSR catalysts, Mg/Al hydrotalcite derived oxides have inferior performance in NOx storage and release at low temperatures. In consideration of excellent NO oxidation activity of Mn-based oxides and potential NOx storage performance of hydrotalcites catalysts, a series of Mn-doped MgAlOx catalysts derived from hydrotalcites were prepared as alternative NSR catalysts and their low-temperature performance have been studied in the present work. It is difficult to differentiate them from the XRD results

After calcination at 600
N2 Adsorption-Desorption Characterization
All the hydrotalcites-derived mixed oxides showed typeof
All the samples showed relatively large surface areasoxides of 100–140
XPS and H2-TPR Characterization
As shown in
NOx Adsorption and Desorption Behavior
As from can beFigure seen from
NOx Lean-Rich Cycling Performance
Asabove shown in
10. Average
Preparation of Catalysts
Catalysts Characterization
NOx Storage and Desorption Measurements
In Situ DRIFTS Experiments
Conclusions

Talk to us

Join us for a 30 min session where you can share your feedback and ask us any queries you have

Schedule a call

Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.