Abstract
Tectonic melange zones within ancient accretionary complexes include various styles of strain accommodation along subduction interfaces from shallow to deep. The ductile-brittle transition at shallower portions of the subduction plate boundary was identified in three tectonic melange zones (Mugi melange, Yokonami melange, and Miyama formation) in the Cretaceous Shimanto Belt, an on-land accretionary complex in southwest Japan. The transition is defined by a change in deformation features from extension veins only in sandstone blocks with ductile matrix deformation (possibly by diffusion-precipitation creep) to shear veins (brittle failure) from shallow to deep. Although melange fabrics represent distributed simple to sub-simple shear deformation, localized shear veins are commonly accompanied by slickenlines and a mirror surface. Pressure-temperature (P-T) conditions for extension veins in sandstone blocks and for shear veins are distinct on the basis of fluid inclusion analysis. For extension veins, P-T conditions are approximately 125 to 220°C and 80 to 210 MPa. For shear veins, P-T conditions are approximately 185 to 270°C and 110 to 300 MPa. The P-T conditions for shear veins are, on average, higher than those for extension veins. The temperature conditions overlap in the range of approximately 175 to 210°C, which suggests that the change from more ductile to brittle processes occurs over a range of depths. The width of the shallow ductile-brittle transition zone can be explained by a heterogeneous lithification state for sandstone and mudstone or high fluid pressure caused by clay dehydration, which is controlled by the temperature conditions.
Highlights
Tectonic mélange zones within ancient accretionary complexes include various styles of strain accommodation along subduction interfaces from shallow to deep
Pseudotachylyte and fluidized shear zones, which indicate dynamic weakening of the fault during displacement, were found in on-land accretionary complexes; this suggests that the geologic features of the seismogenic slips along subduction interfaces are visible in on-land accretionary complexes (e.g., Ikesawa et al, 2003; Kitamura et al, 2005; Ujiie et al, 2007; Meneghini et al, 2010; Hashimoto et al, 2012; Saito et al, 2013)
Extension veins related to mélange fabrics and shear veins cutting the mélange fabrics have been well documented, with detailed pressure-temperature conditions from the Mugi mélange, Miyama formation, and Yokonami mélange in the Cretaceous Shimanto Belt (e.g., Hashimoto et al, 2002, 2003; Matsumura et al, 2003; Hashimoto et al, 2012); these data can be a key in understanding the relation between ductile deformation for mélange and brittle failure in lithified shale matrices
Summary
Tectonic mélange zones within ancient accretionary complexes include various styles of strain accommodation along subduction interfaces from shallow to deep. Extension veins related to mélange fabrics and shear veins cutting the mélange fabrics have been well documented, with detailed pressure-temperature conditions from the Mugi mélange, Miyama formation, and Yokonami mélange in the Cretaceous Shimanto Belt (e.g., Hashimoto et al, 2002, 2003; Matsumura et al, 2003; Hashimoto et al, 2012) (see locations in Figure 1); these data can be a key in understanding the relation between ductile deformation for mélange and brittle failure (shear veins) in lithified shale matrices.
Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.