Abstract
Recently, HfxZr1−xO2 (HZO) thin films have been widely investigated to achieve low power device applications such as ferroelectric random access memory (FeRAM) and ferroelectric field effect transistor (FeFET), due to its stable ferroelectricity even in extremely thin region (~10 nm) and CMOS applicability [1]. Moreover, matured atomic layer deposition (ALD) techniques of HfO2 and ZrO2 enable the fabrication of three-dimensional structure required for future memory devices. TiN top- and bottom-electrodes (TE- and BE-TiN) are typically used as stressor layers to fabricate metal-ferroelectric-metal (MFM) capacitors with HZO films because TiN electrodes provide the mechanical stress required for the formation of the unstable ferroelectric orthorhombic phase [2]. However, this method is suitable only for MFM capacitors, cannot be applied to FET structures. On the other hand, in our previous research, the HZO film fabricated using a polycrystalline ZrO2 nucleation layer, inserted between the HZO film and the BE-TiN, results in the large remanent polarization (2P r = P r + − P r −) [3]. Therefore, the HZO film with top- and bottom-ZrO2 nucleation layers is expected to improve the ferroelectricity. In this study, we fabricated two types of MFM capacitors with HZO films crystallized using top- and bottom-TiN stressor layers and ZrO2 nucleation layers, and discuss the ferroelectricity and the leakage current (J) properties of two types of MFM capacitors. The TiN/ZrO2/HZO/ZrO2/TiN capacitors with top- and bottom-ZrO2 nucleation layers (D-ZrO2) were fabricated as follows: A 2-nm-thick bottom-ZrO2 layer was deposited on the BE-TiN by ALD at 300°C using (C5H5)Zr[N(CH3)2]3 precursor and H2O gas. Next, a 10-nm-thick HZO film was deposited on the bottom-ZrO2 layer by ALD at 300°C using (Hf/Zr)[N(C2H5)CH3]4 (Hf/Zr = 1/1) cocktail precursor and H2O gas. A 2-nm-thick top-ZrO2 layer was then deposited on the HZO film using the same ALD conditions. After that, post-deposition-annealing (PDA) was carried out at 600°C for 1 min in a N2 atmosphere. Finally, TE-TiN was fabricated on the top-ZrO2 layer by DC sputtering. Two types of TiN/HZO/TiN capacitors with 10-nm-thick HZO films were also prepared as references. One is the capacitor annealed before TE-TiN deposition (w/o), the other is the capacitor annealed after TE-TiN deposition under the same annealing process (D-TiN). The Hf:Zr ratio in the HZO film was estimated to be 0.43:0.57 by energy dispersive x-ray spectroscopy analysis. Fig. 1 shows the polarization-electric field (P-E) hysteresis curves of w/o, D-TiN, and D-ZrO2. All of the capacitors exhibited hysteresis loops in the range from −3.0 to 3.0 MV/cm. The 2P r value was increased in the following order: w/o (12 µC/cm2) < D-TiN (24 µC/cm2) < D-ZrO2 (29 µC/cm2). The ratio of ferroelectric orthorhombic phase was increased in the following order: w/o < D-TiN < D-ZrO2, from x-ray diffraction patterns (not shown). Therefore, we determined that the top- and bottom-ZrO2 nucleation layers play an important role for the ferroelectric orthorhombic phase formation of HZO films. Fig. 2 shows the relationship between the J value at 1.0 V and the 2P r value of w/o, D-TiN, and D-ZrO2. For D-TiN case, the 2P r value was approximately 2.0 times larger than that of w/o probably due to the mechanical stress from TE-TiN. However, the J value of D-TiN was increased in the low voltage region compared to w/o. On the other hand, for D-ZrO2 case, the 2P r value was about 2.4 times larger than that of w/o. Moreover, the J value of D-ZrO2 was lower by one order of magnitude than that of D-TiN due to the larger thickness of D-ZrO2 than that of D-TiN. Based on these experimental results, the HZO films exhibited significantly superior ferroelectricity using double ZrO2 nucleation layers compared to that fabricated using double TiN stressor layers. This work was supported partly by Grant-in-Aid for JSPS Research Fellow and CREST, JST. [1] J. Müller et al., Appl. Phys. Lett. 99, 112901 (2011). [2] S. J. Kim et al., Appl. Phys. Lett. 111, 242901 (2017). [3] T. Onaya et al., Appl. Phys. Express 10, 081501 (2017). Figure 1
Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.