Failure Analysis and Failure Investigation of UZ/ACPT1 SS SIDUM Ejector Condenser

Desalination of brackish water by nanofiltration and reverse osmosis

Hybrid membrane system for desalination and wastewater treatment : Integrating forward osmosis and low pressure reverse osmosis

Safe drinking water for the coastal areas of Bangladesh has become a big challenge. Arsenic adulteration and salinity intrusion in surface water body has accelerated the scarcity of water in the coastal region. As situation ameliorating and also investment for water-borne diseases is decreasing, it becomes the major threat for a third-world country like Bangladesh. There are lots of alternatives for water supply but there are also a huge number of constraints. Most of the traditional dug wells (DW), ring wells (RW) and alternative pond sand filters (PSF) are now inoperative due to shortage of fresh surface water body and also adequate maintenance. Except a few, most of the shallow tube wells (STW) and deep tube wells (DTW) in coastal areas face arsenic (As) contamination. There could be a blended solution for these problems based on existing situation, constraint, hydrogeology and individual’s economy. Different kinds of filters, reverse osmosis (RO), solar desalination plants (low-cost and small scale) and fuel-powered desalination plants (high-cost and large scale), etc., would be a good solution for mitigation of these problems. Solar PSF and rain water harvesting (RWH) might be an effective solution for some areas, respectively where fresh water and rainfall is abundant. Keywords: Arsenic contamination, salinity intrusion, climate change, pond sand filter, rain water harvesting, desalination, natural disaster

In today’s present world, billions of people live without reliable access to clean drinking water, and as populations continue to grow, freshwater sources begin to disappear at an equally rapid pace. In an effort to combat these issues, desalination has been introduced as a solution to abstract water from untouched resources. However, while desalination can produce additional potable water, it is also heavily criticised for its flaws; namely cost, energy consumption, and environmental pollution. Thus, in order to promote desalination as a sustainable solution for both the present day and future, improvements need to be implemented to produce less costly, more energy efficient, and environmentally friendly desalination plants. This paper reviews all of the current desalination methods in today’s global market, evaluating which methods are most sustainable for the future of desalination. Options for renewable energies to replace fossil fuels are also studied, as well as various brine disposal methods which can produce more environmentally safe and sustainable desalination facilities. Among the literature reviewed, reverse osmosis was found to be the world’s most sustainable method of desalination due to its energy efficiency and production capacity, while solar photovoltaics were found to be the popular choice among renewable energies. Zero liquid discharge was also found to be the most environmentally friendly method of brine waste disposal, although research in the field was very limited. Each method was closely evaluated and compared among its competitors, offering a detailed perspective on the sustainable state of desalination.

The origin and continuation of mankind is based on water. Water is one of the most abundant resources on earth, covering three-fourths of the planet’s surface. Water is one of the earth’s most abundant resources, covering about three-quarters of the planet’s surface. The reason for this apparent contradiction is, of course, that - 97.5% of the earth’s water is salt water in the oceans and only 2.5% is fresh water in ground water, lakes and rivers and this supplies most human and animal needs. It would be feasible to address the water-shortage problem with seawater desalination; however, the separation of salts from seawater requires large amounts of energy which, when produced from fossil fuels, can cause harm to the environment. The discharge from desalination plants is almost entirely water, and .01 percent is salt. Desalination is a process that extracts minerals from saline water. Solar-powered desalination technologies can be used to treat non-traditional water sources to increase water supplies in rural, arid areas. Water is the basis of life, the origin of human endurance, and the prime material base to guarantee the economy significant development of a country. This solar desalination technique explains the diminutive and extensive-period feasibility of via solar energy as a system to influence desalination. Seawater and briny water were considered, as well as liquid waste. This protocol summarizes that solar desalination expenditure remains lower to exchange saline water into clean water. Water scarceness is a rising dilemma for large regions of the world. Access to safe, fresh and pure clean drinking water is one of the most important and prime troubles in different parts of the world. Among many of water cleansing technologies solar desalination/distillation/purification is one of the most sustainable and striking method engaged to congregate the supply of clean and pure drinkable water in remote areas at a very sound cost. Six types of dripper having discharge 3 - 8 lh-1 were installed one by one and measured discharge and volume of clean water indicated that at 6 lh-1 untreated water discharge have maximum evaporation and volume of clean water was 19.2 lh-1 at same temperature and radiations. Now strategy was developed that when increased the temperature the intake discharge of untreated water must be increased and salt drained water two times more than treated water.

Nowadays, water and electricity are closely interdependent essential sources in human life that affect socio-economic growth and prosperity. In other words, electricity is a fundamental source to supply a seawater desalination process, while fresh water is used for cooling this power plant. Therefore, mutual vulnerability of water treatment and power generation systems is growing because of increased potable water and electricity demands especially during extremely-hot summer days. Hence, this paper presents a novel framework for optimal short-term scheduling of water-power nexus aiming to minimize total seawater desalination and electricity procurement cost while satisfying all operational constraints of conventional thermal power plants, co-producers and desalination units. Moreover, advanced adiabatic compressed air energy storage (CAES) with no need to fossil fuels can participate in energy procurement process by optimal charging during off-peak periods and discharging at peak load hours. A mixed integer non-linear programming (MINLP) problem is solved under general algebraic mathematical modeling system to minimize total water treatment cost of water only units and co-producers, total fuel cost of thermal power plants and co-generators. Ramp up and down rates, water and power generation capacities and balance criteria have been considered as optimization constraints. It is found that without co-optimization of desalination and power production plants, load-generation mismatch occurs in both water and energy networks. By incorporating CAES in water-power grids, total fuel cost of thermal units and co-producers reduce from $1222.3 and $24933.2 to $1174.8 and $24636.8, respectively. In other words, application of CAES results in $343.9 cost saving in benchmark water-power hybrid grid.

This study was a descriptive study to assess the bacteriological quality of Port Sudan drinking water sources and its subsidiary network until it reaches the consumers; in the period October 2005 and April 2007. Ten samples as negative control, and ninety samples were collected from seven different sources and examined bacteriologically to detect the possible bacterial contamination according to the detection of indicator organisms (total coliform, faecal coliform and Escherichia Coli) and their count. Analysis was done by two methods including multiple tube method (also named most probable number (MPN)) and membrane filtration method (MF). Results obtained revealed the analysis of negative control showed no bacterial detection. The analysis of surface water (fresh water) indicated the presence of the indicator organisms (all three types) with the highest average concentrations 1800+org/100 ml by MPN and (1567 org/ 100 ml by MF. Tubes from wells at the water source were contaminated with total coliform only and with low average concentration of 10.6 org/100ml by MPN and 9.8 org/100ml by MF. Drinking water samples, after treatment also indicated presence of contamination due to the presence of three types of indicator organisms with figures 793 org /100ml by MPN and 542 org/100ml by MF (average). This may indicate that the chemical used in treatment or methods of application are questionable. Desalination water, on the other hand, showed minimal contamination at the site of desalination plant. However, the same water was found to be contaminated during distribution (tankers & jericans). Samples taken from the drinking water network (houses, reservoirs) were highly contaminated by the three groups of indicator organisms. Therefore, it was not suitable for human consumption. Also the study has shown the following grade, 24.4% of all tested samples were excellent, 5.6% of all tested samples were satisfactory, 12.2% of all tested samples were suspicious, 57.8% of all tested samples were unsatisfactory.

Corrosion experience data bank system for desalination and power plants (corex)

Water crises are predicted to be amongst the risks of highest concern for the next ten years, due to availability, accessibility, quality and management issues. Knowledge of the microbial communities indigenous to drinking water is essential for treatment and distribution process control, risk assessment and infrastructure design. Drinking water distribution systems (DWDSs) ideally should deliver to the consumer water of the same microbial quality as that leaving a treatment plant (“biologically stable” according to WHO). At the start of this Ph.D. program water microbiology comprised conventional culture dependent methods, and no studies were available on microbial communities from source to tap. A method combining 16S rRNA gene pyrosequencing with flow cytometry was developed to accurately detect, characterize, and enumerate the microorganisms found in a water sample. Studies were conducted in seven full-scale Dutch DWDSs which transport low-AOC water without disinfectant residuals, produced from fresh water applying conventional treatment. Full-scale studies were also conducted at the desalination plant and DWDS of KAUST, Saudi Arabia where drinking water is produced from seawater applying RO membrane treatment and then transported with chlorine residual. Furthermore, biological stability was evaluated in a wastewater reuse application in the Netherlands. When low-AOC water was distributed without disinfectant residuals, greater bacterial richness was detected in the networks, however, temporal and spatial variations in the bacterial community were insignificant and a substantial fraction of the microbiome was still shared between the treated and transported 10 water. This shared fraction was lower in the system transporting water with chlorine residual, where the eukaryotic community changed with residence time. The core microbiome was characterized and dominant members varied between the two systems. Biofilm and deposit-associated communities were found to drive tap water microbiology regardless of water source and treatment scheme. Network flushing was found to be a simple method to assess water microbiology. Biological stability was not associated with safety. The biological stability concept needs to be revised and quantified. Further research is needed to understand microbial functions and processes, how water communities affect the human microbiome, and what the “drinking” water microbiome is like in undeveloped countries.

Purpose: The invention relates to the oil industry, inorganic chemistry, in particular, to the methods of complex processing of formation water, using flare gas of oil and gas field as fuel for producing enriched concentrates of iodine, bromine, magnesium and valuable trace elements, as well as desalinated water (technical and drinking water). The technology includes pre-cleaning of formation water from mechanical impurities and oil using adsorbents, followed by evaporation of water under vacuum, condensing water vapor in the barometric condenser, using of condensed water vapor as the coolant, using of saline water as a coolant of hot water coming out of the barometric condenser to 15–20 °C. The novelty of the design?: The novelty of the design is to get a comprehensive treatment of formation water, using flare gas of oil and gas field as fuel for obtaining enriched concentrates of iodine, bromine, magnesium and valuable trace elements, as well as desalinated water (technical and drinking water)....

Due to the shortage of clean and fresh water, especially in the coastal regions there is an urgent need to look for alternative water sources to meet people needs and compensate the reduction in groundwater. Desalination is one of such alternative water sources that can solve water shortage problem in Libya and other countries where face the same conditions. Desalination is the main technology that has been developed globally over the past three decades to meet the increasing demand for fresh and clean water. The objective of this paper is to highlight the conventional and non conventional water resources in Libya. In this context, our paper intends to present an overview on seawater desalination technology in Libya and why it should be accommodated as a strategic and ultimate solution for water shortage.

Sea water desalination is a developing technology producing potable water with many applications worldwide particularly in arid areas. It is an energy intensive process and its integration with renewable energies can produce low-carbon fresh water. Among several water desalination technologies reverse osmosis is the dominant method, based on semi-permeable membranes, producing high quality clean water. The island of Crete, Greece has moderate water resources while their demand is increasing for several reasons. Unfortunatelly, its supply is adversely affected by climate crisis. One method to increase the supply of potable water in Crete is the desalination of seawater using reverse osmosis. The water desalination plants can be powered by solar and wind energy which are abundant in the island. The integration of seawater desalination with renewable energies results in the production of fresh water with low carbon impacts. A SWOT analysis of using solar and wind electricity to power the water desalination plants in Crete has been implemented. It is indicated that there are several strengths and many opportunities for developing seawater desalination plants powered by green electricity in the island. It is concluded that the use of solar-PV and wind electricity for powering seawater desalination plants in Crete reduces the carbon footpritnt of the produced drinkable water minimizing the impacts to climate change.

Hybrid systems in seawater desalination-practical design aspects, status and development perspectives

The occurrence of disinfection by-products (DBPs) of chlorine dioxide (ClO2) in drinking water, namely: chlorite, chlorate, and THMs as well as the concentration of ClO2 were investigated. Two hundred ninety four drinking water samples were collected during the time period from March to August 2014. The water samples were collected from seven desalination plants (DPs), four reservoirs and eight mosques distributed in South and North Qatar. The ClO2 level was ranged from 0.38 to less than 0.02 mg/L, with mean value of 0.17, 0.12, and 0.04 mg/L in the desalination plants (DPs), the reservoirs (R), and the mosques (M), respectively. The chlorite level was varied from 12.78 – 436.36 ppb with median values varied from 12.78 to 230.76, from 77.43 to 325.25, and from 84.73 to 436.36 ppb in the DPs, the reservoirs, and the mosques, respectively. While chlorate was varied from 10.66 ppb to 282.71 ppb with mean values varied from 35.58 to 282.72 ppb, from 11.02 to 200.69, and from 10.66 to 150.38 ppb in the DPs, R, and M respectively. However, the average value of THMs was 4.90 ppb, while maximum value reached 76.97. Lower disinfectant residual was observed in few samples, however this could be attributed to the normal decomposition reaction of ClO2 with organic and inorganic compounds, including biofilms, pipe materials, corrosion products, formation of slime or may due to the fact the water in distribution system experience water aging problem. Significant differences were observed in the concentration level of chlorite, chlorate and THMs between DPs, reservoirs and the mosques. However, the concentrations of all DBPs fell within the range of the regulatory limit set by GSO 149/2009, WHO and KAHRAMAA (KM). It is recommended to slightly increase the average ClO2 dosage at the DPs. Such slight increase would provide safer margin at the customer point of use in case of any microbial activities. Consideration must be given to the overall demand and should account for seasonal variations, temperature, and application points. As well as a monitoring approach is recommended for the drinking water safety assessment. Re-conducting the study to include other DPs of ClO2 is recommended.

The world demand for potable water is increasing steadily with growing population.Desalination using solar energy is suitable for potable water production from brackish and seawater.In this paper, we presents design, fabrication and testing of double slope solar still with external flatted and internal parabolic reflectors and also optimization of external flat reflector tilt angle for Egyptian climatic conditions.The external flat reflector tilted at (30°, 45°, 60° and 75°) on the horizontal plane.The depth of water inside basin still is 1cm.Experimental results were compared with conventional double slope solar still.Optimum tilt angle is found to be 60° with a maximum daily productivity of 9.89 lit/m 2 .