Abstract
The aim of this study was to investigate the influence of fineness and heat-treatment on the pozzolanic and engineering properties of volcanic ash. To this end, two different fineness levels of volcanic ash, ultra-fine (VAF) and fine (VA), without and after heat treatment at different temperatures (VA550, VA650, and VA750), were partially substituted for cement. In addition to the control (100% cement), five binary mortar mixes, each containing 20% of the different types of volcanic ash (VAF and VA; heat-treated and not), were prepared. First, X-ray fluorescence (XRF), X-ray powder diffraction (XRD), particle size analysis, and modified Chappelle tests were used to characterize the material. All mortar mixes were then tested for compressive strength development, water absorption, and apparent porosity. Finally, the microstructure of each of the mixes was evaluated by performing XRD, thermogravimetric analysis (TGA), and Fourier transform infrared spectroscopy (FTIR) analyses on paste samples at 91 days post-formation. The XRD and Chappelle reactivity results revealed increased pozzolanic reactivity with increasing volcanic ash fineness. In contrast, heat treatment adversely affected the pozzolanic reactivity of the volcanic ash due to the formation of crystalline phases at high temperatures. The mortars containing VAF20 (VAF, no heat, at 20%) showed slightly improved compressive strength (69.6 MPa) than the control (68.1 MPa) and all other binary mixes (66.7, 63.5, 64.2, and 63.9 MPa for VA20, VA20-550, VA20-650, and VA20-750, respectively) at 91 days. The mortar containing VAF20 demonstrated the lowest level of water absorption (9.3%) and apparent porosity (19.1%) of all mixes, including the control. The XRD results for the paste samples show that both VA and VAF showed the least intensity of portlandite phase, as compared to the control and other binary mixes. TGA results also show that binary mixes of VA and VAF have a reduced amount of portlandite, resulting in the densification of the mixes’ microstructures. With the addition of VAF, there is a significant shift in the FTIR band from 980 to 992 cm−1, which causes the formation of additional C–S–H gels that lead to the densification of the paste matrix. These results demonstrate that VAF exhibits high pozzolanic reactivity, making it suitable for use as a natural pozzolan that can partially substitute cement in the production of strong, durable, and environmentally friendly concrete.
Highlights
The aim of this study was to determine the influence of fineness and heat treatment of volcanic ash used as a partial replacement for cement to produce a high-performance sustainable mortar
The volcanic ash passed through sieve no. 450 (VA) was heated at three different temperatures (550, 650, and 750 ◦ C) in order to determine the effect of heat treatment on the mechanical and microstructural properties (Figure 2)
The results show that water absorption (WA) and apparent porosity (AP) values for mortars containing heated-treated VA were higher as compared to mortar containing untreated VA or Control Mortar (CM)
Summary
A significant amount of natural resources is consumed by buildings and infrastructure, creating an ongoing sustainability challenge. Concrete is the second most consumed material on the planet, after water. In 2006, it was estimated that about 25 billion tons of concrete are produced annually worldwide [1–5]. The production of cement peaked in 2016 at 4 billion tons, which indicates the huge amount of greenhouse gases being released into the atmosphere along with the enormous amount of water and aggregates that are utilized in making concrete. Global cement production accounts for around 7% of total carbon dioxide emissions. In order to produce 1000 kg of cement, 4–7 GJ of energy is required, which releases 800–1000 kg of carbon dioxide gas into the atmosphere. CO2 emissions contribute to climate change and global warming [6–11]. The demand for low-carbon concrete for climate change mitigation and adaptation increases daily
Sign-in/Register to view highlights & summary Sign-in/Register to access full text options 
Free) 
Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Schedule a call
