Abstract

Multilevel inverters are a type of power electronic circuit that converts direct current (DC) to alternating current (AC) for use in high-voltage and high-power applications. Many recent studies on multilevel inverters have used field-programmable gate arrays (FPGAs) as a switching controller device to overcome the limitations of microcontrollers or DSPs, such as limited sampling rate, low execution speed, and a limited number of IO pins. However, the design techniques of most existing FPGA-based switching controllers require large amounts of memory (RAM) for storage of sampled data points as well as complex controller architectures to generate the output gating pulses. Therefore, in this paper, we propose two types of FPGA-based digital switching controllers, namely selective harmonic elimination (SHE) and sinusoidal pulse width modulation (SPWM), for a 21-level multilevel inverter. Both switching controllers were designed with minimal hardware complexity and logic utilisation. The designed SHE switching controller mainly consists of a four-bit finite state machine (FSM) and a 13-bit counter, while the SPWM switching controller employs a simple iterative CORDIC algorithm with a small amount of data storage requirement, a six-bit up-down counter, and a few adders. Initially, both digital switching controllers (SHE and SPWM) were designed using the hardware description language (HDL) in Verilog codes and functionally verified using the developed testbenches. The designed digital switching controllers were then synthesised and downloaded to the Intel FPGA (DE2-115) board for real-time verification purposes. For system-level verification, both switching controllers were tested on five cascaded H-Bridge circuits for a 21-level multilevel inverter model using the HDL co-simulation method in MATLAB Simulink. From the synthesised logic gates, it was found that the designed SHE and SPWM switching controllers require only 186 and 369 logic elements (LEs), respectively, which is less than 1% of the total LEs in an FPGA (Cyclone IV E) chip. The execution speed of the SHE switching controller implemented in the FPGA (Cyclone IV E) chip was found to be a maximum of 99.97% faster when compared with the microcontroller (PIC16F877A). The THD percentage of the 21-level SHE digital switching controller (3.91%) was found to be 37% less than that of the SPWM digital switching controller (6.17%). In conclusion, the proposed simplified design architectures of SHE and SPWM digital switching controllers have been proven to not only require minimal logic resources, achieve high processing speeds, and function correctly when tested on a real-time FPGA board, but also generate the desired 21-level stepped sine-wave output voltage (±360 VPP) at a frequency of 50 Hz with low THD percentages when tested on a 21-level cascaded H-Bridge multilevel inverter model.

Highlights

  • Over the last decade, multilevel inverters (MLIs) have garnered significant research attention in high-voltage and high-power applications, such as high-power motor drives, power conditioning, renewable energy conversion, and power distribution, due to their simple structure, modularity, and transformer-less circuit [1,2,3,4]

  • This section discusses the results of synthesised selective harmonic elimination (SHE) and sinusoidal pulse width modulation (SPWM) digital switching controllers using the Intel field-programmable gate arrays (FPGAs) (Cyclone IV E) chip, register transfer-level (RTL) simulation results in a digital-simulator timing waveform, real-time hardware-measurement results, and system-level verification using hardware description language (HDL) co-simulations in MATLAB Simulink

  • From the finite state machine (FSM) are grouped according to their dedicated H-bridge circuit

Read more

Summary

Introduction

Multilevel inverters (MLIs) have garnered significant research attention in high-voltage and high-power applications, such as high-power motor drives, power conditioning, renewable energy conversion, and power distribution, due to their simple structure, modularity, and transformer-less circuit [1,2,3,4]. To compensate for the low supply voltage, the semiconductor power switches are coupled to several low-DC sources, which are configured into multilevel structures to produce a high-power output. These power switches accomplish power conversion with the assistance of a digital switching controller by synthesising multiple DC voltage sources into a high-voltage stepped output waveform [3,6,7]. The modular structure of the H-bridge inverter enables cascading and stacking of inverters for high-power and high-voltage applications.

Objectives
Methods
Results
Conclusion
Full Text
Published version (Free)

Talk to us

Join us for a 30 min session where you can share your feedback and ask us any queries you have

Schedule a call