Abstract
Objectives: To measure and compare the bond strength between three different types of ceramics and resin cement, as well as the degree of conversion of resin cement after using different light-curing units and curing modes. Methods: Three types of ceramics—Leucite-reinforced (Empress CAD), Lithium disilicate (Emax CAD), and Zirconia (Emax ZirCAD)—of varying thicknesses (1.5 mm and 2.0 mm) were bonded to a light-cure resin cement (Variolink Esthetic LC). Light-curing was carried out using a monowave LCU (3M Elipar DeepCure-S LED Curing Light with irradiance of 1470 mW/cm2) and with polywave LCU (Ivoclar Bluephase PowerCure) using High, Turbo, and 3 s curing modes, respectively (1200, 2100, 3000 mW/cm2). A chevron-notch bond strength test (total n = 288) was conducted to calculate the fracture energy and interfacial bond strength (J/m2). The degree of cure (%DC) of the residual resin cement on debonded surfaces was measured using Fourier Transform Infrared Spectroscopy (FTIR). Collected data were statistically analysed under SPSS ver. 27 by conducting an ANOVA and Bonferroni post hoc test. The mode of failure was established using a scanning electron microscope (SEM). Results: A significant difference in interfacial bond strength was found between the three types of ceramic material groups (p < 0.01). Cement cured through Empress that was 2 mm thick showed the highest bond strength (1.36 ± 0.46 J/m2), while the lowest was observed (0.26 ± 0.07 J/m2) in 2 mm Emax CAD using the 3 s mode. The use of different LCUs and curing modes had a significant influence on the %DC of resin cement seen in all groups, except 2 mm Emax ZirCAD. The dominant mode of failure for Empress, EmaxCAD, and EmaxZirCAD were cohesive, adhesive, and mixed, respectively. Conclusions: The type of ceramic and its thickness can significantly affect bond strength, and the results showed that polywave LCU is more effective than monowave LCU when curing through ceramics.
Highlights
Publisher’s Note: MDPI stays neutralThe change from traditional full-gold crowns and porcelain-fused-to-metal (PFM) to all-ceramic restorations over the past few decades is considered to be one of the fastest paradigm shifts in restorative dentistry [1,2]
The type of ceramic and its thickness can significantly affect bond strength, and the results showed that polywave light-curing unit (LCU) is more effective than monowave LCU when curing through ceramics
The Empress 2.0 mm and EmaxCAD 1.5 mm groups demonstrated significant differences in bond strength when cured under different light-curing units and curing modes
Summary
Publisher’s Note: MDPI stays neutralThe change from traditional full-gold crowns and porcelain-fused-to-metal (PFM) to all-ceramic restorations over the past few decades is considered to be one of the fastest paradigm shifts in restorative dentistry [1,2]. The prevalence of all-ceramic restorations is recorded at 80.2% [3], 69% [4] and 57.7% [5] in the United States of America (USA), United Kingdom (UK) and New Zealand (NZ), respectively. These surveys showed that more than half of the population in these countries prefer all-ceramic restorations, highlighting the increasing popularity of ceramics as a restorative material. The rapid advances and success of Computer-Aided Design and Computer-Aided Manufacturing (CAD/CAM) technology coupled with the high public desire for tooth-coloured restorations, justify the continuous demand and manufacture of all-ceramic restorations [7]. A stable bond with regard to jurisdictional claims in published maps and institutional affiliations
Sign-in/Register to view highlights & summary Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Schedule a callDisclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.
