Abstract
The paper reports a new transversal study of dielectric coating effects on high voltage (HV) electrodes in SF <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">6</sub> and eco-friendly gases like CO <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sub> , dry air and N <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sub> for real-size gas insulated switchgear (GIS). From a practical viewpoint, the breakdown electric field (BDE) data of the following test conditions are collected; 1) large effective electrode area over about 5 × 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">4</sup> mm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> , 2) actual GIS cylindrical configuration of utilization factor of around 0.6, 3) high gas pressures up to 1.9 MPa for actual GIS. The BDEs of dielectric coated electrodes relative to those of bare electrodes (normalized BDEs) are systematically evaluated as a function of dielectric coating thickness and gas pressure. As a result, the normalized BDEs in percentage terms are 105-150% (average value of around 110%), which does not depend on the gases. Remarkable performances of the normalized BDEs of 120-150%, which correspond to nearly 90% of the theoretical BDEs of the gases, are observed in SF <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">6</sub> and CO <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sub> for "thick casting epoxy coating", "thin coating of comparable dielectric performance to casting epoxy" and "hard anodic-oxide coating & PTFE-immersion" that have fewer defects inside. The normalized BDEs in N <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sub> , however, show poorer dielectric performances than the other gases especially in the high pressure region above 1.0 MPa. The dielectric coating effects are more pronounced as increasing the thickness for all the gases. The pressure dependences of the dielectric coating effects are not clearly recognized for all the gases and all the coating conditions except for the "thick casting epoxy coating". The coating effect in N <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sub> decreases slightly as raising gas pressure. The application examples and application limits of the dielectric coatings to GIS are also presented. These new cross-sectional studies of dielectric coated electrodes are an effective approach to get new findings to realize a future eco-friendly compact GIS.
Sign-in/Register to access full text options 
Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Schedule a callMore From: IEEE Transactions on Dielectrics and Electrical Insulation
Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.
