Abstract

BackgroundTo evaluate the feasibility and clinical outcomes of vaginoplasties using a neovaginal polylactic acid prosthesis made with 3-dimensional (3D) printing technology as an intraneovaginal mould.MethodsThis was an interventionist, prospective, and multicentre clinical pilot investigation of a sanitary product (PACIENA prosthesis®) aiming to recruit and operate on 8 patients over 6 months with a follow-up period of 6 months. Only six patients with Rokitansky syndrome and one patient with Morris syndrome (7 patients in total) were operated on in two university hospitals: “La Fe”, Valencia (H1) and “Arrixaca”, Murcia (H2). Interventions: Extensive surgical dissection of a defined space between the urethra and bladder in the front and of the rectum in the back as well as insertion of the PACIENA prosthesis® covered with Interceed® were performed. After 12 days, the prosthesis was changed to the silicone-covered version for daily application.ResultsIn the 6 patients with Rokitansky syndrome (86%), the primary endpoint (satisfactory vaginal outcome in terms of appearance, function, and sensation without relevant additional morbidity) was achieved, although only 2 patients (28%) were sexually active at the end of 6 months of follow-up. The patient with Morris syndrome withdrew from the study after 1 month. Patients without bacterial colonization showed positive Schiller tests at 1 month, and subsequent biopsies showed adequate keratinization and epidermization. Epithelization and iodopositivity were delayed in the patients who developed inflammatory granulomas.ConclusionsGood anatomical and functional results can be achieved with the PACIENA prosthesis® for vaginoplasties without skin grafts. However, adequate patient selection and education, good surgical techniques and haemostasis, postoperative support, and prevention of bacterial colonization are important.Trial registrationThis clinical study was approved by the Ethical Clinical Investigation Committee of San Juan University Hospital on September 27, 2016, to be conducted in the participating centres; it was authorized by the Spanish Agency of Medicines and Health Products (AEMPS) on April 24, 2017 (exp. no. 585/16/EC), to be carried out in that hospitals.

Highlights

  • To evaluate the feasibility and clinical outcomes of vaginoplasties using a neovaginal polylactic acid prosthesis made with 3-dimensional (3D) printing technology as an intraneovaginal mould

  • Study objective This study aimed to evaluate the feasibility and clinical outcomes of vaginoplasty using a Poly-Lactic Acid (PLA) prosthesis (PACIENA prosthesis®) as an intraneovaginal mould in patients with vaginal agenesis undergoing surgery following McIndoe’s technique without skin grafts

  • Our study shows that neovaginal formation and epidermization with the performance of vaginoplasty following McIndoe’s technique without the use of skin grafts and with the use of a PLA prosthesis, covered with Interceed®, as an intraneovaginal mould can be achieved with good anatomic and functional results, especially if other adverse effects can be alleviated

Read more

Summary

Introduction

To evaluate the feasibility and clinical outcomes of vaginoplasties using a neovaginal polylactic acid prosthesis made with 3-dimensional (3D) printing technology as an intraneovaginal mould. Good results have been achieved by covering the prosthesis with Interceed® [8], and other authors [9, 10] have obtained good results without using skin grafts, with evidence of squamous epithelization of the neovaginal vault. Acién et al [11,12,13] suggested that by using a prosthesis made of poly-lactic acid (PLA, a biodegradable polymer derived from lactic acid often used as a scaffold in tissue engineering and regenerative medicine [14, 15] and whose contribution to epithelization has been studied by different authors [16, 17]) and designed and manufactured with 3-dimensional (3D) printing technology as a vaginal mould, skin grafting could be avoided, and vaginoplasty would be simpler, with good anatomical and functional results. We do not know of any other neovaginal prostheses for humans with the design, printing and characteristics of our PLA prosthesis

Objectives
Methods
Results
Discussion
Conclusion
Full Text
Published version (Free)

Talk to us

Join us for a 30 min session where you can share your feedback and ask us any queries you have

Schedule a call