Abstract
Introduction. The earth cutter resource depends on the characteristics of the materials they are made from. In particular, the important parameters that directly affect the tillage tool parts efficiency and durability are the values and ratios of the coefficients of relative wear resistance of the two-layer parts materials, as a rule of the hardened deposited layer and the base material (steel). It is established that the characteristics of the relative wear resistance of the materials for earth cutter parts vary depending on the treated soil properties. The objectives of the study are to consider the influence of soil conditions on the values of the relative wear resistance coefficients of two-layer earth cutter part materials and to carry out a comparative assessment of their resource and use efficiency. Materials and Methods. The authors gave a generalized dependence of the wear proportionality to the existing specific pressures values. The characteristics of soil abrasion were given. The scientific substantiation of the changes in the characteristics of the materials wear resistance at various values of specific pressures was given. Results. The results of the operational resource tests and the studies of two-layer and monometallic earth cutters are presented. The influences of the values of the operating specific pressures on the coefficients of the relative wear resistance of the materials for the tillage machine parts are determined. Discussion and Conclusion. The authors have found out that the coefficients of relative wear resistance of materials are not constant, but vary depending on the current surface specific pressures. The correlation of the specific pressure values with the parameters of the tillage operation, in particular with the furrow slice hardness was established. It has been found that while increasing the cultivated soil hardness, the coefficients of various materials relative wear resistance get closer to each other. The difference varies from 1.80 to1.85 times.
Highlights
The earth cutter resource depends on the characteristics of the materials they are made from
It is established that the characteristics of the relative wear resistance of the materials for earth cutter parts vary depending on the treated soil properties
The objectives of the study are to consider the influence of soil conditions on the values of the relative wear resistance coefficients of two-layer earth cutter part materials and to carry out a comparative assessment of their resource and use efficiency
Summary
Установлено, что характеристики относительной износостойкости материалов почворежущих деталей меняются в зависимости от свойств обрабатываемой почвы. Целью исследования стало изучение влияния почвенных условий на значения коэффициентов относительной износостойкости материалов двухслойных почворежущих деталей и сравнительная оценка их ресурса и эффективности применения. Научно обосновано изменение характеристик износостойкости материалов при различных значениях удельных давлений. Представлены результаты эксплуатационных ресурсных испытаний и исследований двухслойных и монометаллических почворежущих рабочих органов в различных почвенных условиях. Определено влияние значений действующих удельных давлений на коэффициенты относительной износостойкости материалов деталей почвообрабатывающих машин. Что коэффициенты относительной износостойкости материалов представляют собой не постоянную величину, а меняются в зависимости от действующих поверхностных удельных давлений. При увеличении твердости обрабатываемой почвы коэффициенты относительной износостойкости различных материалов сближаются. Контент доступен по лицензии Creative Commons Attribution 4.0 License.
Sign-in/Register to view highlights & summary Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
Schedule a callDisclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.
