Abstract
The paper presents the main results of developing and researching a new principle for controlling the step-down transformer on-load tap changer (OLTC), which coordinates the OLTC operation with the electrical parameters of the electric-arc steelmaker, compensators installed in the high-power and ultrahigh-power EAF power supplies, and the mains. The proposed principle consists in pre-determining the operating voltage ranges on the mains-transformer primary side for all OLTC tap positions taking into account the existing of both the electric-arc steelmaking facility and the mains. The static VAR compensator (SVC) control system is improved by adding a block for finding the mains-transformer OLTC tap position number so as to use new position-switching algorithms. The problem of optimizing the OLTC tap-position switching in mains-transformers supplying power to electric-arc steelmaking facilities under significant mains-voltage deviations is analyzed on the basis of evidence from three Russian steelworks companies. We herein discuss the particularities selecting the mains-transformer OLTC positions in two SVC control modes, one consisting in keeping zero consumption of reactive power from the mains, and the other one consisting in maintaining a coordinate voltage in the common EAF and SVC connection point. The effect of the proposed solutions is found from the results obtained by means of mathematical modeling of electric-arc steelmaking facilities in MATLAB Simulink. We discuss the options for further improvement of principles for coordinating the operation of automatic transformer-voltage regulators (AVR) with the parameters of steelmakers, compensators, and mains.
Highlights
Введение На металлургических предприятиях электросталеплавильные комплексы, имеющие в своем составе мощные и сверхмощные дуговые печи, получают питание от отдельного распределительного устройства, которое, в свою очередь, связано с питающей сетью через понизительный трансформатор
Уровень напряжения во внешней районной сети может изменяться в больших пределах как в течение одних суток, так и за более продолжительный период времени
Ser. Power Engineering, 2018, vol 18, no
Summary
Все изменения напряжения в питающей сети трансформируются на низкую сторону сетевого трансформатора, что приводит к отклонению. Без проведения дополнительных исследований действие автоматики АРНТ является сложнопрогнозируемым, например, в периоды понижения и повышения уровня напряжения в сети 35 кВ, наблюдаемого при работе ДСП под током и в ее технологические паузы, при условии, что первичное и вторичное напряжения сетевого трансформатора в этот момент равны пороговым значениям рабочих диапазонов двух соседних ступеней РПН или в случае управления СТК по напряжению, когда вторичное напряжение трансформатора зависит не только от его значения на первичной стороне. С целью улучшения электрических характеристик дуговых печей за счет рационального управления устройством РПН сетевого трансформатора проведено усовершенствование системы управления СТК путем добавления в нее блока определения номера ступени РПН, который реализует согласованную работу АРНТ с режимами электросталеплавильного комплекса и питающей сети. В периоды технологической паузы ДСП допустимая величина положительного отклонения напряжения при выборе положения РПН ограничивается значением максимально допустимого
Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
More From: Bulletin of the South Ural State University series "Power Engineering"
Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.