Transparent Electrodes Research Articles

Efficient and Highly Stable Lateral Perovskite Single‐Crystal Solar Cells through Crystal Engineering and Weak Ion Migration

AbstractThe lateral device structure for perovskite solar cells (PSCs) has garnered significant attention, primarily due to its elimination of the need for expensive transparent electrodes. However, the performance of lateral devices, which are more sensitive to crystal quality and charge carrier transport bottlenecks, has lagged far behind the predominant vertical PSCs. Herein, by modulating the crystal nucleation and growth processes of thin FA0.75MA0.25PbI3 (FA = formamidinium; and MA = methylammonium) single crystals, crystal quality and carrier transport are improved, resulting in a power conversion efficiency (PCE) of 12.64%, a record for lateral PSCs. Investigation of the device's stability reveals that iodide ion migration is suppressed due to a reduction in the iodide vacancy concentration combined with weak interface iodide ion migration. It is shown that the latter effect is a result of the perpendicular direction of the ion migration and the electric field in the lateral PSCs. Consequently, these lateral single‐crystal PSCs display remarkable operational stability, retaining 100% of their initial PCE after 1200 h of steady‐state output at the maximum power point voltage (Vmpp) under 1 sun illumination. This work highlights the advantages of lateral single‐crystal devices and their potential to address key ion migration issues of PSCs.

Facile Nanowelding Process for Silver Nanowire Electrodes Toward High‐Performance Large‐Area Flexible Organic Light‐Emitting Diodes

AbstractDespite considerable interest, uniform and robust flexible transparent conducting electrodes (FTCEs) that can be seamlessly integrated and used for highly efficient large‐area flexible oganic light‐emitting diodes (OLEDs) remain elusive. In this study, a large‐area fabrication of uniform transparent electrodes for high‐performance flexible OLEDs by exploiting the rapid nanowelding process of silver nanowires (AgNWs) onto polyethylene terephthalate substrate under Xe‐lamp irradiation and mechanical pressing treatment is reported. The performance of AgNWs FTCEs is significantly enhanced by applying the Xe‐lamp beam irradiation for 5 s and subsequent compression at 20 MPa for 15 s, achieving a low sheet resistance of 26.5 Ω sq−1, a high transmittance of 95.2% (at 550 nm), and very smooth surfaces with root‐mean‐square of 5.4 nm. Meanwhile, the nanowelded AgNWs FTCEs maintain excellent electrical conductivity (only a 2.96% increase in ΔR/R0) after 1000 bending cycles. The resulting AgNWs FTCEs‐based green phosphorescent OLED achieves an unprecedented external quantum efficiency (EQE) of 23.7% and a current efficiency as high as 81.5 cd A−1. Benefiting from the uniform properties for resulting AgNWs FTCEs, the fabricated flexible OLED with a large area of 25 × 25 mm2 still retains a high EQE of 22.2% and a current efficiency of 78.0 cd A−1.

Enhanced Performance of Complementary Electrochromic Device with Hierarchical‐Porous NiO x Decorated ITO Glasses as the Transparent Conductive Electrodes

To pursuit advancing electrochromic technology, the preparation of a novel hierarchical‐porous NiOx‐decorated ITO transparent conductive electrode was developed through the vapor‐assisted conversion and subsequent calcination processes. The modified transparent electrode exhibited advantages in the electrodeposition of conductive polymer films, which significantly enhanced electrochromic cycling stability. Moreover, the complementary electrochromic device based on NiOx‐decorated ITO transparent electrode was fabricated, demonstrating rapid response time (1.75 s for coloration and 0.87 s for bleaching), high optical contrast (53.4%), and remarkable cycling stability (90% optical contrast retention over 2000 cycles). This finding holds prominent potential for applications in related fields.

Achieving optimal balance: tuning electrical and optical characteristics of carbon electrodes for emerging photovoltaics.

Transparent and conductive electrodes (TCEs) are essential for various optoelectronic and photovoltaic applications, but they often require expensive and complex fabrication methods. In this paper, a unique low-cost, eco-friendly, and scalable method of fabricating TCEs using spray-coated carbon ink is investigated. Firstly the carbon particles used for this process underwent a size reduction from 20 microns to 0.96 microns via ball milling. Then ink was prepared by mixing graphite powder (for conductivity), ethyl cellulose (for viscosity), and toluene (for solubility) with different weight-per-volume ratios (w/v) of 5%, 10%, and 15%. The TCEs were fabricated by spray coating the ink onto glass substrates using an airbrush. The sheet resistance (Ω sq-1) and transparency (%) of the TCEs were measured by a digital multimeter (DMM) probe method and a UV-vis spectrophotometer, respectively. The sheet resistance of the TCEs decreased linearly from 60 to 20 Ω sq-1, while the transparency decreased exponentially from 37.18% to 18.88% as the ink concentration increased from 5% to 15% w/v. This paper also reports the reflectance and absorbance values for each ink concentration. The results demonstrate that spray-coated carbon ink TCEs achieve sheet resistance and transparency values of 20 Ω sq-1 and 18.88%, respectively, with low-cost and eco-friendly materials and methods, which are desirable for optoelectronic and photovoltaic applications. These TCEs can play an important role as electrodes in semi-transparent perovskite cells enhancing their stability and overall efficiency.

Synthesis of New Ruthenium Complexes and Their Exploratory Study as Polymer Hybrid Composites in Organic Electronics

Polymeric hybrid films, for their application in organic electronics, were produced from new ruthenium indanones in poly(methyl methacrylate) (PMMA) by the drop-casting procedure. Initially, the synthesis and structural characterization of the ruthenium complexes were performed, and subsequently, their properties as a potential semiconductor material were explored. Hence hybrid films in ruthenium complexes were deposited using PMMA as a polymeric matrix. The hybrid films were characterized by infrared spectrophotometry and atomic force microscopy. The obtained results confirmed that the presence of the ruthenium complexes enhanced the mechanical properties in addition to increasing the transmittance, favoring the determination of their optical parameters. Both hybrid films exhibited a maximum stress around 10.5 MPa and a Knoop hardness between 2.1 and 18.4. Regarding the optical parameters, the maximum transparency was obtained at wavelengths greater than 590 nm, the optical band gap was in the range of 1.73–2.24 eV, while the Tauc band gap was in the range of 1.68–2.17 eV, and the Urbach energy was between 0.29 and 0.50 eV. Consequently, the above comments are indicative of an adequate semiconductor behavior; hence, the target polymeric hybrid films must be welcomed as convenient candidates as active layers or transparent electrodes in organic electronics.

Bright Bifacial White-Light Illumination by Highly Deformable Electroluminescent Devices Based on Transparent Ionic-Hydrogel Electrodes and Quantum-Dot Color Conversion.

Deformable alternating-current electroluminescent (ACEL) devices are of increasing interest because of their potential to drive innovation in soft optoelectronics. Despite the research focus on efficient white ACEL devices, achieving deformable devices with high luminance remains difficult. In this study, this challenge is addressed by fabricating white ACEL devices using color-conversion materials, transparent and durable hydrogel electrodes, and high-k nanoparticles. The incorporation of quantum dots enables the highly efficient generation of red and green light through the color conversion of blue electroluminescence. Although the ionic-hydrogel electrode provides high toughness, excellent light transmittance, and superior conductivity, the luminance of the device is remarkably enhanced by the incorporation of a high-k dielectric, BaTiO3. The fabricated ACEL device uniformly emits very bright white light (489cdm-2) with a high color-rendering index (91) from both the top and bottom. The soft and tough characteristics of the device allow seamless operation in various deformed states, including bending, twisting, and stretching up to 400%, providing a promising platform for applications in a wide array of soft optoelectronics.

Evaporation-induced self-assembled ultrathin AgNW networks for highly conformable wearable electronics

The flexibility and stability of transparent electrodes play a crucial role in the growing popularity of flexible devices, especially in potential wearable electronics. To date, various solution-coating techniques have been developed for fabricating silver nanowire (AgNW) flexible bioelectronics. However, achieving the orderly distributed patterns of AgNW without undesirable aggregations still poses a grand challenge. Here, an approach to realize regular patterned ultrathin AgNW networks on a freestanding electrospun PVDF-TrFE frame by evaporation-induced self-assembly is proposed. The patterning mechanism of evaporating AgNW colloidal suspension is investigated from experimental and theoretical analysis. The influence of evaporation-induced flow inside colloidal freestanding membranes on forming regular square hole-shaped arrays, selective deposition of AgNW, and aligning them along the artificial pinning array are addressed. Owing to the orderly arrangement of AgNW networks, the resultant flexible electrode achieves ultrathin thickness (about 5 μm), high optical transmittance (87.8%), and low sheet resistance (8.4 Ω·sq−1) with a relatively low dosage of AgNW (9 μg·cm−2). The electrode exhibits excellent durability during cyclic bending (50,000 times) and stretching (50% strain). The resistance remains virtually unchanged during 200 days in everyday environments. Furthermore, the excellent conformability and breathability of the flexible transparent electrode attached to the human skin demonstrates its potential application as an e-skin sensor. Our findings reliably urge a simple approach to underscore better outcomes with effective patterns by self-assembly of AgNW for highly conformal wearable electronics.

Thermally Induced Phase Separation of the PEDOT:PSS Layer for Highly Efficient Laminated Polymer Light-Emitting Diodes.

Among various conductive polymers, the poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) film has been studied as a promising material for use as a transparent electrode and a hole-injecting layer in organic optoelectronic devices. Due to the increasing demand for the low-cost fabrication of organic light-emitting diodes (OLEDs), PEDOT:PSS has been employed as the top electrode by using the coating or lamination method. Herein, a facile method is reported for the fabrication of highly efficient polymer light-emitting diodes (PLEDs) based on a laminated transparent electrode (LTE) consisting of successive PEDOT:PSS and silver-nanowire (AgNW) layers. In particular, thermally induced phase separation (TIPS) of the PEDOT:PSS film is found to depend on the annealing temperature (Tanneal) during preparation of the LTE. At Tanneal close to the glass transition temperature of the PSS chains, a PSS-rich phase with a large number of PSS- molecules enhances the work function of the PEDOT:PSS on the glass-side surface relative to the air side. By using the optimized LTEs, bidirectional laminated PLEDs are obtained with a total external quantum efficiency of 2.9% and a turn-on voltage of 2.6 V, giving a comparable performance to that of the reference bottom-emitting PLED based on a costly evaporated metal electrode. In addition, an analysis of the angular characteristics, including the variation in the electroluminescence spectra and the change in luminance according to the emission angle, indicates that the laminated PLED with the LTE provides a more uniform angular distribution regardless of the direction of emission. Detailed optical and electrical analyses are also performed to evaluate the suitability of LTEs for the low-cost fabrication of efficient PLEDs.

Designing Rules for an Efficient Metallic Mid-Infrared Transparent Electrode Dedicated to Nanocrystal-Based Devices

Designing Rules for an Efficient Metallic Mid-Infrared Transparent Electrode Dedicated to Nanocrystal-Based Devices

Highly flexible and transparent amorphous Indium doped tin oxide on bio-compatible polymers for transparent wearable sensors

Highly transparent and flexible amorphous Sn-doped In2O3 (a-ITO) films deposited on flexible and bio-compatible cyclic olefin polymer (COP) substrate using a direct-current magnetron sputtering at room temperature were used as flexible and transparent electrodes for transparent wearable sensors. The figure of merits (FoM) value was calculated to determine the optimal sputtering process for the a-ITO electrodes by varying the direct current power, working pressure, oxygen flow rate, and a-ITO thickness. The optimized a-ITO/COP with a high FoM value of 8.9 exhibited a low sheet resistance of 36 Ohm/square, average transmittances of 89.5% in the visible wavelength region, and a small critical bending radius of 7 mm, which are acceptable transparent electrodes for fabrication of wearable and transparent wearable sensors. To demonstrate the feasibility of the a-ITO/COP substrate as a promising wearable sensor, we examined the performance of wearable temperature sensors, wearable heaters, and wearable glucose sensors. The successful operation of a-ITO/COP-based temperature sensors with high sensitivity, transparent heaters with a saturation temperature of 87.8 °C at 6 V, and glucose sensors with high sensitivity indicates that a-ITO/COP is a promising bio-compatible electrode for next-generation wearable bionic electronics.

Flexible Short-Wave Infrared Transparent Electrode Based on Broadband Induced Transmission Mechanism

Flexible Short-Wave Infrared Transparent Electrode Based on Broadband Induced Transmission Mechanism

Encapsulation of Flexible Transparent Electrodes Based on Indium Zinc Tin Oxide with Highly Transparent and Mechanically Robust Polymer Dielectrics

This study was aimed at comprehensively investigating the utility of PMMA and CYTOP as encapsulation layers for flexible transparent electrodes composed of indium zinc tin oxide (IZTO). Optical modeling and experimental techniques were combined to assess the viability of PMMA and CYTOP as encapsulation materials. Optical modeling suggested that PMMA and CYTOP are well-suited for IZTO encapsulation. Subsequent experiment confirmed that the transmittance values of IZTO-films remained unaffected when encapsulated with PMMA and CYTOP. To examine the influence of encapsulation on mechanical resilience, all film, including untreated IZTO and IZTO treated with PMMA/CYTOP, were subjected to 20,000 bending cycles. The mechanical stability and optical properties of the IZTO film were considerably enhanced when encapsulated with these insulating materials. The improvement in transmittance was attributable to the lower refractive index of PMMA and CYTOP. Furthermore, scanning electron microscopy images demonstrated that the remarkable flexibility of PMMA and CYTOP effectively prevented the formation of cracks on the IZTO film, underscoring their pivotal role in enhancing the mechanical robustness of IZTO. In summary, this research highlights the potential of PMMA and CYTOP as efficient encapsulation materials for IZTO-based flexible transparent electrodes, offering dual benefits in terms of optical performance and mechanical durability.

Flexible Force Sensor Based on a PVA/AgNWs Nanocomposite and Cellulose Acetate.

Nanocomposites are materials of special interest for the development of flexible electronic, optical, and mechanical devices in applications such as transparent conductive electrodes and flexible electronic sensors. These materials take advantage of the electrical, chemical, and mechanical properties of a polymeric matrix, especially in force sensors, as well as the properties of a conductive filler such as silver nanowires (AgNWs). In this work, the fabrication of a force sensor using AgNWs synthesized via the polyol chemical technique is presented. The nanowires were deposited via drop-casting in polyvinyl alcohol (PVA) to form the active (electrode) and resistive (nanocomposite) sensor films, with both films separated by a cellulose acetate substrate. The dimensions of the resulting sensor are 35 mm × 40 mm × 0.1 mm. The sensor shows an applied force ranging from 0 to 3.92 N, with a sensitivity of 0.039 N. The sensor stand-off resistance, exceeding 50 MΩ, indicates a good ability to detect changes in applied force without an external force. Additionally, studies revealed a response time of 10 ms, stabilization of 9 s, and a degree of hysteresis of 1.9%. The voltage response of the sensor under flexion at an angle of 85° was measured, demonstrating its functionality over a prolonged period. The fabricated sensor can be used in applications that require measuring pressure on irregular surfaces or systems with limited space, such as for estimating movement in robot joints.

Electroless silver plating combined with laser direct writing technology: For the fabrication of flexible silver mesh transparent electrodes

Ultra-thin metal meshes are emerging as potential candidates for ln2O3 (ITO) due to their mechanical properties, excellent flexibility and optoelectronic properties. However, the manufacturing of high-performance metal meshes is often accompanied by thin-layer metal deposition processes such as sputtering deposition and vacuum evaporation, as well as the combination of imprinting templates, which increases the complexity of the process and production costs. Herein, we have established a finite element theoretical calculation model for predicting the optoelectronic performance of metal meshes and propose a method based on electroless plating silver combined with laser direct writing to prepare high-quality Ag meshes. It provides a way to achieve rapid and economical production of Ag mesh transparent electrodes. The ultra-thin Ag mesh exhibits excellent transmittance (90.2 % at 550 nm), the transmittance is close to 95 % above the 600 nm wavelength band and the sheet resistance is 13.0 Ω/sq. Furthermore, The Ag mesh exhibits excellent mechanical flexibility, indicated by the fact that the resistance is almost unchanged after 5000 bending cycles.

High-performance composite transparent electrode composed of ultra-long silver nanowires and antimony-doped tin oxide nanoparticles

Composite transparent conductive electrodes (TCEs) consisting of silver nanowires (AgNWs) and conductive metal oxides are very promising for flexible optoelectronic devices due to their smooth surface morphology and high chemical stability. However, it is still challenging to ensure high optoelectronic performance and long-term stability in practical applications. Here, we solved these problems by coating antimony-doped tin oxide (ATO) nanoparticles dispersion on ultra-long AgNWs network using waterborne polyurethane (WPU) binder. Ultra-long nanowires occupy less wire-wire junctions and space than short nanowires, thus increasing the optoelectronic performance and flexibility of the composite TCE. WPU improves the adhesion and stability of ATO nanoparticles to the substrate and AgNWs network. The fabricated composite TCE showed a low sheet resistance of 11.9 Ω sq−1, good optical transmittance of 83% at 550 nm and a figure of merit (FOM) of 162 compared to PET/ITO electrode. It also showed excellent mechanical flexibility, adhesion to the substrate and solvent stability. Furthermore, the long-term conductivity was maintained under ambient conditions for 60 days.

An electrochemiluminescent magneto-immunosensor for ultrasensitive detection of hs-cTnI on a microfluidic chip

Sensitive detection and precise quantitation of trace-level crucial biomarkers in a complex sample matrix has become an important area of research. For example, the detection of high-sensitivity cardiac troponin I (hs-cTnI) is strongly recommended in clinical guidelines for early diagnosis of acute myocardial infarction. Based on the use of an electrode modified by single-walled carbon nanotubes (SWCNTs) and a Ru(bpy)32+-doped silica nanoparticle (Ru@SiO2)/tripropylamine (TPA) system, a novel type of electrochemiluminescent (ECL) magneto-immunosensor is developed for ultrasensitive detection of hs-cTnI. In this approach, a large amount of [Ru(bpy)3]2+ is loaded in SiO2 (silica nanoparticles) as luminophores with high luminescent efficiency and SWCNTs as electrode surface modification material with excellent electrooxidation ability for TPA. Subsequently, a hierarchical micropillar array of microstructures is fabricated with a magnet placed at each end to efficiently confine a single layer of immunomagnetic microbeads on the surface of the electrode and enable 7.5-fold signal enhancement. In particular, the use of transparent SWCNTs to modify a transparent ITO electrode provides a two-order-of-magnitude ECL signal amplification. A good linear calibration curve is developed for hs-cTnI concentrations over a wide range from 10 fg/ml to 10 ng/ml, with the limit of detection calculated as 8.720 fg/ml (S/N = 3). This ultrasensitive immunosensor exhibits superior detection performance with remarkable stability, reproducibility, and selectivity. Satisfactory recoveries are obtained in the detection of hs-cTnI in human serum, providing a potential analysis protocol for clinical applications.

Ecofriendly Cellulose Substrate‐Based Flexible Transparent Electrode for Flexible Organic Solar Cells with Efficiency Over 18%

Flexibility is a key advantage of organic solar cells (OSCs), and the power conversion efficiencies (PCEs) of flexible OSCs (FOSCs) are primarily constrained by flexible transparent electrodes (FTEs). While much attention has been devoted to the study of conductive layers on FTEs, the importance of flexible substrates in influencing the properties of FTEs and the performance of FOSCs is often overlooked. In this study, an FTE is developed using an eco‐friendly ethyl cellulose (EC) substrate and silver nanowires (AgNWs) as the conductive electrode. The FTE exhibits a high transmittance of up to 88% at 550 nm and a low sheet resistance of 17.65 Ω/□. Consequently, FOSCs based on the EC/PI FTEs achieve a remarkable PCE of 18.05%, comparable to that on the rigid ITO substrate. The flexible devices also demonstrate excellent bending and peeling durability even under extreme bending conditions.

Development of eutectic gallium-indium-based transparent conductive electrodes on flexible substrates for touch sensor integration

In this study, the adaptability of liquid metal (LM)-based transparent conductive electrodes (TCEs) to flexible substrates and their potential applications in various electronics fields were investigated. To achieve this, conventional microfabrication techniques were employed to pattern polydimethylsiloxane (PDMS) channels and introduce an Eutectic Gallium-Indium (EGaIn) LM with the aim of enhancing transmittance and reducing sheet resistance. Microfluidic channel structures with varying pitch lengths and widths were fabricated in the types of grid patterns, labeled Pattern A (2000 μm pitch, 40 μm width), Pattern B (2000 μm pitch, 80 μm width), Pattern C (200 μm pitch, 40 μm width), and Pattern D (200 μm pitch, 80 μm width. The corresponding average transmittance values for the EGaIn LM-based TCE were 90 %, 71.8 %, 61.8 %, and 43.2 % for Patterns A, B, C, and D, respectively. To illustrate the potential in touch sensor applications, resistance changes in Patterns A, B, C, and D were assessed under applied forces ranging from 0 N to 150 N, revealing resistance changes of 0.0265 Ω, 0.03617 Ω, 0.03977 Ω, and 0.11629 Ω, respectively.

Sustainable, low-cost, high-contrast electrochromic displays via host–guest interactions

Electrochromic (EC) displays with electronically regulating the transmittance of solar radiation offer the opportunity to increase the energy efficiency of the building and electronic products and improve the comfort and lifestyle of people. Despite the unique merit and vast application potential of EC technologies, long-awaited EC windows and related visual content displays have not been fully commercialized due to unsatisfactory production cost, durability, color, and complex fabrication processes. Here we develop a unique EC strategy and system based on the natural host and guest interactions to address the above issues. A completely reusable and sustainable EC device has been fabricated with potential advantages of extremely low cost, ideal user-/environment friendly property, and excellent optical modulation, which is benefited from the extracted biomass EC materials and reusable transparent electrodes involved in the system. The as-prepared EC window and nonemissive transparent display also show comprehensively excellent properties: high transmittance change (>85%), broad spectra modulation covering Ultraviolet (UV), Visible (Vis) to Infrared (IR) ranges, high durability (no attenuation under UV radiation for more than 1.5 mo), low open voltage (0.9 V), excellent reusability (>1,200 cycles) of the device's key components and reversibility (>4,000 cycles) with a large transmittance change, and pleasant multicolor. It is anticipated that unconventional exploration and design principles of dynamic host-guest interactions can provide unique insight into different energy-saving and sustainable optoelectronic applications.

Laser shock-enabled optical–thermal–mechanical coupled welding method for silver nanowires

Silver nanowires (AgNWs) are recognized as highly promising materials for flexible and transparent electrode applications. However, existing material-processing methods fail to achieve uniform and reliable AgNWs junctions. In this study, we propose a new method using the laser shock effect combined with the laser heating effect, for creating AgNW junctions within thin films. We explored the welding mechanism of AgNWs through optic-thermal welding, laser shock-enabled mechanical welding, and laser-shock-enabled optical-thermal-mechanical (LS-OTM) experiments, as well as numerical simulations, and the results demonstrate that the innovative mechanism of the LS-OTM process lies in its utilization of laser shock to adjust the gap between the nanowire junctions, which in turn achieves a fine control of the thermal effect of the heating laser localised surface plasmon resonance, and the atomic diffusion in the solid state at intermediate temperature under the action of the impact force is the mechanism of the formation of high-quality junctions. We prepared flexible transparent conductive films and studied their transmittance, conductivity, and thermal properties, the results show that the flexible transparent conductive films prepared by LS-OTM welding method have excellent transmittance, conductivity, and thermal properties, this verifies the feasibility and effectiveness of this processing strategy. The LS-OTM method is a viable solution for manufacturing transparent, conductive films from AgNWs for emerging applications such as flexible heated films, flexible displays, and wearable medical devices.