Pure Films Research Articles

Synergetic Improvement of Flexoelectric Coefficient in liquid Crystal Embedded Flexible PVDF Polymer Composite for Energy Harvesting Applications.

Flexoelectricity is the universal electric polarization of dielectrics upon exertion of a non-uniform strain gradient. With the advancement of nano-technology and miniaturization of electronic devices, flexoelectricity holds the promise to address the power requirements for such device operation. The direct flexoelectric effect in liquid crystal (LC) embedded Poly(vinylidene fluoride) (PVDF) polymer films is examined for the first time by the application of external strain on the films. Physical characterizations such as DSC, dielectric spectroscopy, XRD and FESEM are carried out to study the composite films' intrinsic and extrinsic properties like dielectric, crystallinity and morphologies. The value of the flexoelectric coefficient (μ12) increases with the concentration of LC incorporation. At 3wt%, μ12 attains a maximum value of 68 nC/m, which is more than a three-fold increase compared to that of the pure PVDF film. The role of Maxwell Wagner Sillars (MWS) polarization in determining flexoelectric polarization in polymer composites is also discussed. Moreover, the influence of the microstructure and domain size formation in determining the flexoelectric response are discussed in detail to infer the behaviour of the flexoelectric coefficients of the films. Potential device applications based on this phenomenon have been proposed for future research in sensing and actuation. This article is protected by copyright. All rights reserved.

Signal oscillations in helium scattering by bismuth atoms in the low energy range

Low Energy Ion Scattering (LEIS) analysis of bismuth selenide (Bi2Se3), a strong 3D topological insulator, revealed oscillations of the detected signal in dependence on primary ion beam energy. Bismuth is a part of the group of elements where oscillatory behaviour was already noticed, such as gallium, indium, or lead. Generally, it is ascribed to quasi-resonant charge exchange processes between primary ion and target atom. Moreover, clear differences exist between data for target atoms in elemental form and for atoms in compound form. A study of Bi signal yields in different material forms was performed for primary He+ projectiles within the energy range from 0.50 to 6.00 keV. A foil of pure Bi, Bi2Se3, Bi2O3 and thin Bi films deposited on several substrates (SiO2, CuOx) by Molecular Beam Epitaxy were analysed. The energy shift in the position of oscillations was observed when the oxygen atoms were present at the surface and bonded to Bi atoms. A description of the Bi ion yield variation is provided to facilitate the quantification process in LEIS.

Advancing soy protein isolate-ulvan film physicochemical properties and antioxidant activities through strategic high-pressure homogenization technique

Soy protein-based films often exhibit poor properties, including limited mechanical strength, stability, and bioactivity, which hinder their extensive application in the food industry, particularly in edible packaging. To enhance the properties of soy protein-based films, we employed high-pressure homogenization (HPH) to modify the soybean protein isolate (SPI) molecules and sought to cross-link SPI with ulvan polysaccharide, which possesses distinctive bioactivities. The results confirmed that soluble ulvan polysaccharides were incorporated into the cross-linking system through hydrogen bonding. Results indicated that HPH treatment enhanced SPI's solubility and surface hydrophobicity (H0), promoting hydrogen bonding and hydrophobic interactions between SPI and ulvan, as evidenced by ζ-potential and turbidity measurements. Structural and microstructural analyses of both individual SPI and composite films, using FT-IR, XRD, CD and SEM, demonstrated a high compatibility between HPH-treated SPI and ulvan. The incorporation of ulvan reduced the films' tensile strength (TS), but higher pressure significantly improved it (p < 0.05). Post-HPH modification, the films exhibited increased contact angle and swelling capacity (p < 0.05), indicating enhanced hydrophobicity. Higher pressure treatments resulted in more opaque and yellowish films, thereby diminishing ultraviolet light transmission. Thermal stability analyses, via TGA-DSC, showed that U-HSPI films had improved thermal stability compared to pure SPI films. Moreover, ulvan inclusion boosted the antioxidant capacity of SPI films, especially after HPH treatment. Overall, this study confirms that HPH modification substantially influences the properties and activities of SPI-based films, and the complex films based on SPI and ulvan with improved physicochemical and antioxidant properties exhibit a great potential in the food packaging field.

Modified Composite Biodegradable Mulch for Crop Growth and Sustainable Agriculture.

Using biodegradable films as a substitute for conventional polyolefin films has emerged as a crucial technology to combat agricultural white pollution. To address the shortcomings in the tensile strength, water vapor barrier properties, and degradation period of PBAT-based biodegradable films, this investigation aimed to create a composite film that could improve the diverse properties of PBAT films. To achieve this, a PBAT/PLA-PPC-PTLA ternary blend system was introduced in the study. The system effectively fused PBAT with PLA and PPC, as evidenced by electron microscopy tests showing no apparent defects on the surface and cross-section of the blended film. The developed ternary blend system resulted in a 58.62% improvement in tensile strength, a 70.33% enhancement in water vapor barrier properties, and a 30-day extension of the functional period compared to pure PBAT biodegradable films. Field experiments on corn crops demonstrated that the modified biodegradable film is more suitable for agricultural production, as it improved thermal insulation and moisture retention, leading to a 5.45% increase in corn yield, approaching the yield of traditional polyolefin films.

Synthesis of novel Stachytarpheta jamaicensis flower liked hexagonal boron nitride nanoribbons (SJF-BNNBs) to efficiently improve the thermal/mechanical/electrical properties of flexible polyimide films

Heat dissipation has become a bottleneck restricting large-scale integration and flexible electronic technologies. This study reports a novel fabrication strategy to prepare flexible stachytarpheta jamaicensis flower-like hexagonal boron nitride nanoribbons (SJF-BNNBs) and their composite films with polyimide (PI). The effect of synthesis conditions on the morphology of SJF-BNNBs was investigated, and the growth mechanism was proposed. The in-plane and through plane thermal conductivities of the 4 wt% SJF-BNNBs/PI composite film reach 5.98 W m−1 K−1 and 0.79 W m−1 K−1, which are 3047 % and 316 % higher than those of the pure PI film, respectively. The in-plane and through plane thermal conduction enhancement efficiencies reach 761.8 % and 78.9 %, respectively. The tensile strength of the composite film is 61.7 % higher than that of pure PI, and maintains excellent electrical insulating and thermal stability properties. Infrared imaging tests verified the excellent heat dissipation performance of the composite film as a thermal interface material and a flexible copper clad laminate substrate, where the operating temperature of device could be reduced by 17.3 °C. To the best of our knowledge, SJF-BNNBs outperform the most efficient thermally conductive electrically insulating filler and are to break the overcome of polymer composites in heat dissipation applications.

Effect of Keratin Waste on Poly(ε-Caprolactone) Films: Structural Characterization, Thermal Properties, and Keratinocytes Viability and Proliferation Studies

Keratin extracted (KE) from chicken feathers was used for the production of composite films comprising poly(ε-caprolactone) (PCL) and keratin (PCL/KE films). The process involved the extraction of keratin from chicken feathers using a 0.1 M NaOH solution, followed by characterization via sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE). The PCL was synthesized through the ring-opening polymerization (ROP) of ε-caprolactone (ԑ-CL) with Sn(Oct)2 as a catalyst. Films were prepared via solvent casting, including pure PCL films and those enriched with different weight percentages of KE (10%, 15%, 25%, and 30%). The films were characterized by differential scanning calorimetry (DSC), thermogravimetric analysis (TG), and scanning electron microscopy (SEM). SEM analysis revealed a more uniform incorporation of KE within the PCL matrix in the case of the 15% keratin-enriched film (PCL/KE15) as compared to other keratin percentages. The thermal analysis showed a positive influence of keratin on the thermal stability of the films. Keratinocytes viability and proliferation tests on the PCL/KE15 film demonstrated compatibility with cells. Collectively, these results hold relevance for potential biomedical applications of PCL/KE films.

Pickering nanoemulsion loaded with eugenol contributed to the improvement of konjac glucomannan film performance

Konjac glucomannan (KGM) is becoming a very potential food packaging material due to its good film-forming properties and stability. However, KGM film has several shortcomings such as low mechanical strength, strong water absorption, and poor self-antibacterial performance, which limits its application. Therefore, in order to enhance the mechanical and functional properties of KGM film, this study prepared Pickering nanoemulsion loaded with eugenol and added it to the KGM matrix to explore the improvement effect of Pickering nanoemulsion on KGM film properties. Compared to pure KGM film and eugenol directly added film, the mechanical strength of Pickering-KGM film was significantly improved due to the establishment of ample hydrogen bonding interactions between the β-cyclodextrin inclusion complex system and KGM. Pickering-KGM film had significant antioxidant capacity than pure KGM film and eugenol directly added KGM film (eugenol-KGM film) (~3.21 times better than KGM film, ~0.51 times better than eugenol-KGM film). In terms of antibacterial activity, Pickering-KGM film had good inhibitory effect on Escherichia coli, Staphylococcus aureus, and Candida albicans, and raspberry preservation experiment showed that the shelf life of the Pickering-KGM film could be extended to about 6 days. To sum up, this study developed a novel means to improve the film performance and provide a new insight for the development and application of food packaging film.

Transparent Cellulose/Multi-Walled Carbon Nanotube Hybrids with Improved Ultraviolet-Shielding Properties Prepared from Cotton Textile Waste.

Plastics offer many advantages and are widely used in various fields. Nevertheless, most plastics derived from petroleum are slow to degrade due to their stable polymer structure, posing serious threats to organisms and ecosystems. Thus, developing environmentally friendly and biodegradable plastics is imperative. In this study, biodegradable cellulose/multi-walled carbon nanotube (MCNT) hybrid gels and films with improved ultraviolet-shielding properties were successfully prepared using cotton textile waste as a resource. It was proven that MCNTs can be dispersed evenly in cellulose without any chemical or physical pretreatment. It was found that the contents of MCNTs had obvious effects on the structures and properties of hybrid films. Particularly, the averaged transmittance of cellulose/MCNT composite films in the range of 320-400 nm (T320-400) and 290-320 nm (T290-320) can be as low as 19.91% and 16.09%, when the content of MCNTs was 4.0%, much lower than those of pure cellulose films (T320-400: 84.12% and T290-320: 80.03%). Meanwhile, the water contact angles of the cellulose/MCNT films were increased by increasing the content of MCNTs. Most importantly, the mechanical performance of cellulose/MCNT films could be controlled by the additives of glycerol and MCNTs. The tensile strength of the cellulose/MCNT films was able to reach as high as 20.58 MPa, while the elongation at break was about 31.35%. To summarize, transparent cellulose/MCNT composites with enhanced ultraviolet-shielding properties can be manufactured successfully from low-cost cotton textile waste, which is beneficial not only in terms of environmental protection, but also the utilization of natural resources.

Electrodeposition of Phase–Pure n–Type Cu2O: Role of Electrode Reactions and Local pH

Cuprous oxide (Cu2O) thin films, antithetically exhibiting n-type conductivity, were electro–deposited on Fluorine-doped Tin Oxide (FTO) coated glass substrates. Linear sweep voltammetry, chronoamperometry, and chronopotentiometry studies coupled with structural characterization of the deposit identify the occurrence of multiple reduction reactions, including “corrosion” of Cu2O to Cu. Interestingly, an underpotential conversion (negative of +0.039 V vs Ag/AgCl) of the Cu2O film to Cu islands is observed during potentiostatic deposition. The same process is also shown as a potential spike in chronopotentiometry curves, during galvanostatic deposition, at current densities that are cathodic of −0.2 mAcm−1. The reason for the formation of Cu is attributed to the decrease in local pH in the vicinity of the working electrode, whence thermodynamic conditions favor the formation of Cu. The proroguation of Cu formation is achieved by continuously stirring the solution, thereby stabilizing the pH at the electrode. Deferment of film corrosion to increasingly longer times is observed with increasing stirring rates. Mott-Schottky analysis of phase-pure films reveals the formation of degenerately doped n-type Cu2O films (n ∼1020 cm−3). The phase pure Cu2O films could be used as an electron transport layer in several photo-conversion devices and ultimately pave the way for an oxide homojunction device.

Enhancement of ferroelectricity in chemical-solution-deposited ZrO2 thin films through fine phase transition control

Recent studies have highlighted the ferroelectric potential of ZrO2 thin films, which offer advantages over HfO2-based ferroelectric materials, such as lower thermal budget and greater natural abundance. In this research, pure ZrO2 ferroelectric thin films were fabricated on Si substrates using chemical solution deposition with all-inorganic precursors. We explored the impacts of film thickness and HfO2 seed layers on phase transition and ferroelectric properties. Notably, an 11 nm thick ZrO2 film exhibited ferroelectric behavior with a remanent polarization of 12.6 μC/cm2. Due to the combined effects of tensile stress and surface energy, the increase in thickness to 30 nm led to a phase transition from the orthorhombic phase to the monoclinic phase and a resultant decrease in remanent polarization. Additionally, the introduction of an HfO2 seed layer facilitated the crystallization of the ferroelectric o-phase, enhancing the remanent polarization to 16.5 μC/cm2 in our ∼8 nm thick ZrO2 thin film with a ∼2 nm thick HfO2 seed layer. These findings provide valuable insights into optimizing ferroelectric properties in ZrO2 thin films through phase transition control.

Fabrication and Investigation of PMMA-Doped 1, 3, 5-Triphenylbenzene (TPB) Thin Film’s Structural, Optical, and Electrical Properties for Optoelectronic Devices

In this experimental work, triphenylbenzene/polymethylmethacrylate (TPB/PMMA) based thin films were deposited using a spin coating to examine their structural, optical, and electrical properties. The deposited thin film has a crystalline nature with an average crystalline size of 27.12 nm, and a dislocation density of 7.1×10-4 nm-2. The absorption spectra of TPB, PMMA, and TPB-PMMA films lie in the range of 200 nm to 500 nm with an optical bandgap of 3.85 eV, for TPB-PMMA. The PL spectra of pure TPB thin film give a constant emission at 360 nm, which is independent of the excitation wavelength in the range of 310 nm–340 nm. The excitation-dependent behaviors for both pure TPB and TPB-PMMA were observed in terms of intensity that first increases and gives maximum intensity for the excitation wavelengths of 328 nm and 315 nm, respectively. From CIE coordinates, it was observed that the TPB-PMMA thin film gives a constant deep blue emission. The effect of TPB-PMMA percentage was examined with the help of IV studies, and at 20% TPB: PMMA, the presence of more TPB molecules was observed resulting in a smaller distance between molecules and a larger number of available paths for current flow. Further, with a rise in temperature from 303K to 353K, the thermal stability of the TPB-PMMA thin film was excellent, and it kept the ohmic behavior. The examined optical bandgap of TPB-PMMA thin film falls within the range that is appropriate for OLEDs with emission in the blue region. In addition, the excellent structural and electrical properties of TPB-PMMA make it a suitable candidate for optoelectronic devices.

Robust Superhydrophobic Films Based on an Eco-Friendly Poly(l-lactic acid)/Cellulose Composite with Controllable Water Adhesion.

Poly(l-lactic acid) (PLLA) featuring desirable biodegradability and biocompatibility has been recognized as one of the promising eco-friendly biomaterials. However, low crystallization and poor mechanical and chemical performances dramatically hamper its practical application. In this work, we report that functionalized cellulose/PLLA composite superhydrophobic stereocomplex films with controllable water adhesion and protein adsorption can be fabricated by a facile approach for the first time. First, cellulose is surface-modified by means of two silanization modification methods. Then, superhydrophobic cellulose/PLLA composite films are prepared through a solvent-evaporation-induced phase separation method. The two cellulose/PLLA composite films exhibit extreme water repellency but tunable water adhesion from sticky to slippery. The protein adsorption capacity of the cellulose/PLLA composite films can also be regulated. In addition, the stereocomplexation of the composite film provides excellent mechanical properties with an elongation at break of 22.36%, which is 237.8% higher than that of a pure PLLA film, which is more suitable for biomaterials. Furthermore, good biodegradability of the PLLA composite films in nature enables the bio-based composites as alternative materials to replace conventional petroleum-based polymers. The superhydrophobic films have also been demonstrated for many applications, including slippery surfaces, liquid transportation without loss, and antifouling.

Green-process preparation and characterizations of optically transparent, thermally stable and mechanically superior regenerated silk-hyaluronate composite films

High-performance regenerated silk-hyaluronate composite films prepared by an environment-friendly process were highly desirable for medical dressing base material. In this study, sericin was removed from silk by steam treatment without using any chemical reagent, and a low concentration solution of Na2CO3 was used as a green process to dissolve silk fibers. Then the obtained silk fibroin was physically blended with sodium hyaluronate to generate optically transparent, thermally stable and mechanically superior regenerated silk-hyaluronate films. The results of structural characterizations and property tests showed that the insoluble silk short fibers prepared by the dissolution of Na2CO3 were dominated by a β-sheet crystalline structure while the soluble silk fibroins by an amorphous structure. Moreover, both insoluble silk short fibers and soluble silk fibroins could form uniform composite films with a low coefficient of thermal expansion after being blended with sodium hyaluronate, which were named as insoluble silk film (ISH) and soluble silk film (SSH), respectively. The tensile strength of ISH could reach 138.8 MPa and SSH reached 153.9 MPa, which were 65.7 % and 30.5 % higher than that of the commercial control insoluble fibroin film (83.8 MPa) and commercial control soluble fibroin film (117.9 MPa), and 173.2 % and 203.0 % higher than that of pure hyaluronate film (50.8 MPa), respectively. Also, ISH and SSH had a modulus higher than 3 GPa. In this study, the low-concentration Na2CO3 method provides a simple and green technique for the preparation of high performance silk-hyaluronate composite materials.

Polyarylene ether nitrile dielectric composites with good formability and processability

High dielectric constant polymer matrix composites are widely used in the domain of dielectric energy storage and electric field regulation depending on their high energy density, easy processing and light weight. Nevertheless, high dielectric constants are often achieved by adding fillers to the polymer, which increase the viscosity of the resin and make processing difficult. In this work, a novel filler GO coated with silicone powder (GO-silicone) was designed and prepared. The silicone powder on the surface of GO acts as a lubricant and improves the dispersion of GO in the polyarylene ether nitrile (PEN) resin, thus enhancing the dielectric properties of the PEN-based composite. The dielectric constant of the PEN/GO-silicone composite film with 4wt% filler loading reaches 15.9 at 1kHz, which is 4.3 times greater than that of the pure PEN film and 1.1 times greater than that of PEN composite simply filled with GO and silicone powder. Besides, the incorporation of GO-silicone declines the viscosity, which is very favorable for the processing and shaping of high dielectric composites. This work provides a novel technical route for the large-scale production of high dielectric composites.

Study on transverse high-velocity impact resistance of carbon nanotube films and their based composites

This paper investigates the resistance of Carbon nanotube (CNT) films and their based composites to transverse high-speed impact and explores the effect of resin content on the impact properties. The study utilizes light gas gun experiments and employs numerical simulation to determine the critical penetration velocities for pure CNT films and those films impregnated with 20%, 50%, and 80% epoxy resin solutions. The results demonstrate that including epoxy resin can enhance CNT films' impact-resisting ability, with a noticeable improvement as the resin content increases The observed strengthening mechanism in CNT resin composite films subjected to high-speed impacts primarily is energy absorption. Based on the above results, CNT films were added to the interlayer of composite laminates. It was found that CNTs could help materials resist impact and ensure the integrity of the laminate structure.

Mechanical and barrier properties of chitosan-based composite film as food packaging: A review

Chitosan can serve as a natural alternative to petroleum-based components in food packaging; however, the mechanical and barrier properties of pure chitosan film possess certain limitations. This paper presents a comprehensive review on the mechanical and barrier properties of composite films formed by combining chitosan-based films with plasticizers, polysaccharides, proteins, and lipids. These composite films often exhibit superior mechanical strength and enhanced barrier performance compared to pure chitosan film, thereby expanding the potential applications of chitosan in food packaging. Chitosan represents an ideal raw material for developing innovative biofilms that can cater to diverse packaging requirements for various food products while offering promising prospects for broad application.

New Surface Modification of Hydrophilic Polyvinyl Alcohol via Predrying and Electrospinning of Hydrophobic Polycaprolactone Nanofibers.

Despite the excellent oxygen barrier and biodegradability of polyvinyl alcohol (PVA), its poor physical properties owing to its inherent hydrophilicity limit its application. In this paper, we report a novel surface modification technique for PVA films, involving the control of the predrying conditions (i.e., amount of residual solvent) of the coated PVA film and adjusting the electrospinning process of hydrophobic polycaprolactone (PCL) nanofibers onto the PVA films. The residual solvent of the coated PVA film was varied by changing the predrying time. A shorter predrying time increased the residual solvent content significantly (p < 0.05) and the flexibility of the coated PVA film. Moreover, scanning electron microscopy depicted the improved physical binding of hydrophobic PCL nanofibers to the hydrophilic PVA surface with increased penetration depth to the PVA film with shorter drying times. The PVA/PCL composite films with different predrying times and electrospun PCL nanofibers exhibited an apparent increase in the contact angle from 8.3° to 95.1°. The tensile strength of the pure PVA film increased significantly (p < 0.05) from 7.5 MPa to 77.4 MPa and its oxygen permeability decreased from 5.5 to 1.9 cc/m2·day. Therefore, our newly developed technique is cost-effective for modifying the surface and physical properties of hydrophilic polymers, broadening their industrial applications.

Ultrasonic-Assisted Electrodeposition of Mn-Doped NiCo2O4 for Enhanced Photodegradation of Methyl Red, Hydrogen Production, and Supercapacitor Applications

This paper presents a novel ultrasonic-assisted electrodeposition process of Mn-doped NiCo2O4 onto a commercial nickel foam in a neutral electroplating bath (pH = 7.0) under an ultrasonic power of 1.2 V and 100 W. Different sample properties were studied based on their crystallinity through X-ray diffraction (XRD), morphology was studied through scanning electron microscopy (SEM), and photodegradation was studied through ultraviolet–visible (UV–Vis) spectrophotometry. Based on the XRD results, the dominant crystallite phase obtained was shown to be a pure single NiCo2O4 phase. The optical properties of the photocatalytic film showed a range of energy band gaps between 1.72 and 1.73 eV from the absorption spectrum. The surface hydroxyl groups on the catalytic surface of the Mn-doped NiCo2O4 thin films showed significant improvements in removing methyl red via photodegradation, achieving 88% degradation in 60 min, which was approximately 1.6 times higher than that of pure NiCo2O4 thin films. The maximum hydrogen rate of the composite films under 100 mW/cm2 illumination was 38 μmol/cm2 with a +3.5 V external potential. The electrochemical performance test also showed a high capacity retention rate (96% after 5000 charge–discharge cycles), high capacity (260 Fg−1), and low intrinsic resistance (0.8 Ω). This work concludes that the Mn-doped NiCo2O4 hybrid with oxygen-poor conditions (oxygen vacancies) is a promising composite electrode candidate for methyl red removal, hydrogen evolution, and high-performance hybrid supercapacitor applications.

The Success of Fabrication of Pure SmFe2 Phase Film with Outstanding Perpendicular Magnetic Anisotropy.

This study used DC magnetron sputtering technology to fabricate Sm-Fe films and systematically investigated the phase transition behavior of Sm-Fe films with different Fe ratios. It was found that at higher Fe content, the films consisted of Sm2Fe17 or SmFe7 phases; as Fe content decreased, the films were mainly composed of SmFe3 or SmFe2 phases; at higher Sm content, the films primarily consisted of Sm phase. Sm is prone to volatilization at high temperatures, so Ta was used as a capping layer to effectively suppress Sm volatilization, successfully synthesizing pure SmFe2 phase films at a nearly 1:2 ratio. The magnetic properties and magnetostrictive behavior of the SmFe2 films were investigated, revealing that pure-phase SmFe2 films exhibit good perpendicular magnetic anisotropy and magnetostriction properties. The larger stress along the perpendicular-to-film direction, resulting from the absence of substrate-induced constraints, contributes to the excellent perpendicular magnetic anisotropy of the films. This study successfully synthesized pure-phase SmFe2 films and discovered a new method for fabricating perpendicularly anisotropic films. The research findings are of great significance for the efficient synthesis of desired films with high phase formation temperatures containing volatile elements.

Theoretical Study of the Phonon and Electrical Conductivity Properties of Pure and Sr-Doped LaMnO3 Thin Films.

The film thickness, temperature, substrate and doping dependence of the phonon energy ω and damping γ, as well as the electrical conductivity, of pure and Sr-doped LaMnO3 thin films near the phase transition temperature TN are investigated using a microscopic model and the Green's function technique. Due to the strong spin-phonon interaction, there appears a kink at TN in the temperature dependence of ω(T) and γ(T). The softening and hardening of the ω = 495 cm-1 (A1g) and ω = 614 cm-1 (B2g) modes is explained by the different sign of the anharmonic spin-phonon interaction constant R. The damping increases with T for both cases because it is proportional to R2. ω decreases whereas γ increases with an increasing Sr concentration. This is due to the strain caused by the difference between the ionic radii of the La and Sr ions. The film thickness dependence is also considered. ω and γ increase strongly with the decreasing film thickness. The electrical conductivity is enhanced after the doping of the LMO thin films with Sr, which could be used for energy storage applications. The observed results are in good qualitative agreement with the experimental data.